7600092 CLARKE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 4

Technical content

ORIGINAL INSTRUCTIONS GC03/26

4 TONNE AUTO-RISE AXLE STAND

MODEL NO: CAX4Q PART NO: 7600092

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SAFETY WARNINGS

  • Read these instructions carefully before use.
  • Although sold separately these stands should be used as a matched pair.
  • DO NOT exceed the axle stand’s maximum load (4000 kg each / 8000 kg per pair), The vehicle weight will be stated in the owners manual.
  • Use only as specified in this manual.
  • NEVER let children play in or around a vehicle that is on axle stands.
  • ALWAYS make sure that before you work below the vehicle, a responsible person is aware in case of injury or accident.
  • DO NOT use more than one pair of axle stands.
  • Replace the warning label if it becomes unreadable available from the Clarke service dept.
  • Use only on a hard, flat surface, for example concrete.
  • Make sure that you chock all the wheels that remain on the ground.
  • Make sure that the supported vehicle cannot move.
  • Set each axle stand below an appropriate point on the vehicle - See your vehicle owners manual for advice.
  • Take care when using the axle stands on a three- wheeled vehicle or trailer.
  • Use stands as a matched pair to support one end of a vehicle only.
  • For your safety, DO NOT attempt to modify these axle stands. WARNING: NEVER WORK UNDER A VEHICLE SUPPORTED ONLY BY A JACK. WARNING: AFTER LIFTING THE VEHICLE, SUPPORT IMMEDIATELY WITH PROPERLY RATED AXLE STANDS

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com USING THE AXLE STANDS 1. Refer to the vehicle handbook for the correct jacking procedure and location of the support points. 2. Raise the vehicle using a suitable lifting jack. 3. Remove the R-clip from the safety pin, then lift up the handle to make the ratchet bar raise up automatically to reach the contact point under the vehicle. 4. Slowly lower the vehicle onto the stand making sure the ratchet mechanism is fully engaged. 5. Insert the safety pin and lock it with the R-clip. 6. After work, raise the vehicle clear of the axle stand and remove the stand. 7. Ensure that all tools, equipment and personnel are clear before carefully lowering the vehicle to the ground. 8. Remove the R-clip from the safety pin, lift up the handle and then press the saddle down to the minimum height. Insert the safety pin and lock it with the R-clip. WARNING: BEFORE USE, MAKE SURE THAT THERE IS NO DAMAGE TO ANY PART OF THE AXLE STAND. IF THERE IS, DO NOT USE. WARNING: IT MUST BE ENSURED THAT THE VEHICLE/LOAD IS CAREFULLY LOCATED ONTO THE CENTRE OF THE AXLE STAND SADDLE. FAILURE TO DO THIS CAN RESULT IN DAMAGE TO THE AXLE STAND, LOSS OF SUPPORT TO THE LOAD, SERIOUS PERSONAL INJURY OR LOSS OF LIFE. WARNING: DO NOT EXCEED THE RATED LOAD OF 8000 KG PER PAIR OR 4000 KG PER STAND. WARNING: USE ONLY ON A HARD, FLAT SURFACE, E.G. CONCRETE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SPECIFICATIONS GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights Model CAX4Q Maximum Height 505 mm Minimum Height 340 mm Maximum Load 4 Tonnes Product Weight 5.2 kg Number of Height Positions 12