© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017
Document overview
- PDF pages: 15
Technical content
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 One world. One KEMET Overview KEMET’s 900 series encapsulated radial leaded ceramic disc capacitors are specifically designed for interference- suppression AC line filtering applications. Having internationally recognized safety certifications, these capacitors are well-suited for applications that require keeping potentially disruptive or damaging line transients and EMI out of susceptible equipment. They are also an ideal solution when needing to suppress line disturbances at the source. Safety Certified Capacitors are classified as either X and/ or Y capacitors. Class X capacitors are primarily used in line-to line (across-the-line) applications. In this application there is no danger of electric shock to humans should the capacitor fail, but could result in a risk of fire. The class Y capacitor is primarily used in line-to-ground (line by-pass) applications. In this application, failure of the capacitor could lead to danger of electric shock. With a working voltage of 400 VAC in line-to-line (Class X)and
400 VAC in line-to-ground (Class Y) applications, these safety
capacitors meet the impulse test criteria outlined in IEC Standard 60384. Meeting subclass X1 and Y1 requirements, these devices are certified to withstand impulses up to 4 KV (X1) and 8 KV (Y1) respectively. These encapsulated devices also meet the flame test requirements outlined in UL Standard 94V–0. Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade)
Ordering Information
C9 3 1 U 101 J V S D A A 7317 Ceramic Series Body Diameter Lead Spacing1 Spec. Capacitance Code (pF) Capacitance Tolerance Rated Voltage Dielectric/ Temp. Char. Design Lead Config. 2 Failure Rate Packaging (C-Spec) C9 = Ceramic 900 Series 0 = 7.0 mm 1 = 8.0 mm 2 = 9.0 mm 3 = 10.0 mm 4 = 11.0 mm 5 = 12.0 mm 6 = 13.0 mm 7 = 14.0 mm 1 = 10.0 mm U = Safety Two significant digits and number of zeroes J = ±5% K = ±10% M = ±20% V = X1
400 VAC
/Y1 400 VAC S = SL Y = Y5P W = Y5U V = Y5V D = Disc A = Straight B = Vertical Kink C = Outside Kink A = N/A See "Packaging C-Spec Ordering Options Table" below 1 "Vertical Kink" and "Outside Kink" lead configurations cannot be combined with the bulk/20 mm lead length option (WL20). 20 mm lead length is only available on capacitors ordered with straight leads (lead configuration ordering code "A"). For nonstandard lead length inquiries, please contact KEMET. 2 Bulk packaging lead length availability is dependent upon "Lead Configuration." See "Dimensions" section of this document to verify availability of a specific lead length option. For nonstandard lead length inquiries, please contact KEMET.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Packaging C-Spec Ordering Options Table Packaging Type Lead Length (mm)2,3 Packaging Ordering Code (C-Spec) Ammo Pack 20.0 +1.5/−1.0 (straight leads) 18.0 +2.0/−0 (preformed leads1) 7317 Bulk Bag 3.0±1.0 WL30 3.5±1.0 WL35 4.0±1.0 WL40 4.5±1.0 WL45 5.0±1.0 WL50 20.0 minimum4 WL20 1 Preformed (crimped) lead configurations include vertical kink, outside kink and inside kink. See "Lead Configurations" and "Ordering Information" sections of this document for further details. 2 "Vertical Kink", "Outside Kink" and "Inside Kink" lead configurations cannot be combined with the bulk/20 mm lead length option (WL20). 20 mm lead length is only available on capacitors with straight leads (lead configuration ordering code "A"). For nonstandard lead length inquiries, please contact KEMET. 3 For nonstandard lead length inquiries, please contact KEMET. 4 Lead length of 20.0 mm minimum only available for straight leads. Benefits
- S afety Standard Recognized (IEC 60384-14) R eliable operation up to 125°C C lass X1/Y1 0 mm lead spacing L ead (Pb)-free and RoHS Compliant H alogen free C apacitance offerings ranging from 10 pF up to 10 nF A vailable capacitance tolerances of ±5%, ±10% and ±20%
- H igh reliability P reformed (crimped) or straight lead configurations N on-polar device, minimizing installation concerns 00% pure matte tin-plated lead finish allowing for excellent solderability E ncapsulation meets flammability standard UL 94V–0
Applications
Typical applications include: L ine-to-line (Class X) filtering L ine-to-ground (Class Y) filtering A ntenna coupling P rimary and secondary coupling (switching power supplies) L ine disturbances suppression (motors and motor controls, relays, switching power supplies, and inverters)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Lead Configurations Straight Vertical Kink Outside Kink D T LL S F 3.0 Maximum D T LL S F
4.0 Maximum
3.0 Maximum D T LL S F
5.0 Maximum
3.0 Maximum Dimensions – Millimeters Lead Configuration Lead Configuration Ordering Code1 S Lead Spacing Tolerance D T e ØF Lead Spacing2 Body Diameter2 Body Thickness Lead Meniscus Lead Diameter Straight A 10.0 ±1.0 See Table 1 - "Product Ordering Codes and Ratings" 3.0 maximum 0.55±0.1Vertical Kink (Preformed) B 10.0 ±1.0 Outside Kink (Preformed) C 10.0 ±1.0 1 Lead Configuration is identified in the 13th character of the ordering code. See "Lead Configuration" and "Ordering Information" sections of this document for further details. 2 Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this document for further details.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Approval Standard and Certification No. Safety Standard Standard No. Subclass Working Voltage Certificate No. VDE (ENEC) IEC 60384–14 X1 400 VAC 40036417 Y1 400 VAC UL CAN/CSA UL 60384–14 and E60384–14 X1 400 VAC E356389 Y1 400 VAC These devices are VDE/ENEC and UL recognized for antenna coupling and AC line-to-line (Class X) and line-to-ground (Class Y) applications per IEC60384–14 and UL 60384–14. Environmental Compliance These devices are Halogen free and RoHS Compliant. They meet all requirements set forth by both EU and China RoHS directives. General Specifications/Performance Characteristics Dielectric/Temperature Characteristic SL Y5P Y5U Y5V Operating Temperature Range: −40°C to +125°C Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC): −1,000 ~ +350 ppm/ Dielectric Withstanding Voltage 4,000 VAC (60±5 seconds at 25ºC) Quality Factor (Q) 30 pF and above: ≥ 1,000 Below 30 pF: ≥ 400 +(20xC)* See “Dissipation Factor” Dissipation Factor (tanδ) at +25ºC 1 See “Quality Factor” 2.50% 2.50% 5.0% Insulation Resistance (IR) Limit at +25°C 10,000 MΩ Minimum (500 VDC applied for 60±5 seconds at 25°C) * C = Nominal capacitance
1 Capacitance and Dissipation Factor (DF) measured under the following conditions:
S L: 1 MHz ±100 kHz and 1.0 ±0.2 Vrms X 5P, Y5U and Y5V: 1 kHz ±50 Hz and 1.0 ±0.2 Vrms N ote: When measuring capacitance, it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as Automatic Level Control (ALC). The ALC feature should be switched to "ON."
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Table 1 – Product Ordering Codes and Ratings (1) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this document, page 2, for further details.) A = S traight B = V ertical Kink C = O utside Kink (2) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this document, page 2, for available options. Dielectric/ Temp. Char. KEMET Part Number Capacitance Capacitance Tolerance Dimensions (mm) Lead Spacing Body Diameter (Maximum) Body Thickness (Maximum) Lead Diameter Bulk Packaging Ammo Packaging SL C901U150JVSD(1)A(2) 15 pF ±5% 7.0 5.0 0.55 ±0.1 10 mm C901U180JVSD(1)A(2) 18 pF C901U200JVSD(1)A(2) 20 pF C901U220JVSD(1)A(2) 22 pF C901U240JVSD(1)A(2) 24 pF C901U270JVSD(1)A(2) 27 pF C901U300JVSD(1)A(2) 30 pF C901U330JVSD(1)A(2) 33 pF C901U360JVSD(1)A(2) 36 pF C901U390JVSD(1)A(2) 39 pF C911U470JVSD(1)A(2) 47 pF 8.0 C911U500JVSD(1)A(2) 50 pF C911U510JVSD(1)A(2) 51 pF C911U560JVSD(1)A(2) 56 pF C911U620JVSD(1)A(2) 62 pF C921U680JVSD(1)A(2) 68 pF 9.0C921U750JVSD(1)A(2) 75 pF C921U820JVSD(1)A(2) 82 pF C931U101JVSD(1)A(2) 100 pF 10.0 Y5P C901U101KVYD(1)A(2) 100 pF ±10% 7.0 5.0 0.55 ±0.1 10 mm C901U151KVYD(1)A(2) 150 pF C901U221KVYD(1)A(2) 220 pF C901U331KVYD(1)A(2) 330 pF C911U471KVYD(1)A(2) 470 pF 8.0 C921U561KVYD(1)A(2) 560 pF 9.0C921U681KVYD(1)A(2) 680 pF C941U102KVYD(1)A(2) 1,000 pF 11.0 Y5U C911U102MVWD(1)A(2) 1,000 pF ±20% 8.0 5.0 0.55 ±0.1 10 mm C921U152MVWD(1)A(2) 1,500 pF 9.0 C931U222MVWD(1)A(2) 2,200 pF 10.0 C951U332MVWD(1)A(2) 3,300 pF 12.0 C961U392MVWD(1)A(2) 3,900 pF 13.0 C971U472MVWD(1)A(2) 4,700 pF 14.0 Y5V C901U102MVVD(1)A(2) 1,000 pF ±20% 7.0 5.5 0.55 ±0.1 10 mm C911U152MVVD(1)A(2) 1,500 pF 8.0 C921U222MVVD(1)A(2) 2,200 pF 9.0 C941U332MVVD(1)A(2) 3,300 pF 11.0 C951U472MVVD(1)A(2) 4,700 pF 12.0 KEMET Part Number Capacitance Capacitance Tolerance Body Diameter (Maximum) Body Thickness (Maximum) Lead Diameter Lead Spacing
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions Item Specification Test Method Operating Temperature Range -40ºC to +125ºC Dielectric Strength Between lead wires No failures The capacitor shall not be damaged when 4,000 VAC(rms) is applied between the lead wires for 60 seconds. Body Insulation No failures The terminals (leads) of the capacitor shall be connected together. A metal foil is tightly wrapped around the body of the capacitor at a distance of about 3 to 4 mm from each terminal. The capacitor is then inserted into a container filled with metal balls approximately 1 mm in diameter. 4,000 VAC(rms) is applied for 60 seconds between the capacitor lead wires and metal balls. Metal Foil Metal Balls about 3 to 4 mm Insulation Resistance (IR) 10,000 MΩ minimum The insulation resistance shall be measured with 500±50 VDC applied after 60±5 seconds of charging. Capacitance Within specified tolerance Y5P, Y5U and Y5V: Capacitance is measured at 1 kHz ±20% and 5 Vrms or less. (20±2°C) SL: Capacitance is measured at 1 MHz ±20% and 1.0±0.2 Vrms (25°C)Dissipation Factor (DF) or Q Temperature Characteristics Specification Y5P, Y5U DF ≤ 2.5% Y5V DF ≤ 5.0% SL ≥ 30 pF: Q ≥ 1,000 < 30 pF: Q ≥ 400 +(20 x C) C = Nominal capacitance Temperature Characteristics Temperature Characteristics Capacitance Change Y5P Within ±10% Y5U Within +22%/−56% Y5V Within ~+30%/−80% SL −1,000 ~+350 ppmºC (+20ºC ~+85ºC) A capacitance measurement is made at each step specified: Step Temperature 1 +20±2ºC 2 −25±2ºC 3 +20±2ºC 4 +85±2ºC 5 +20±2ºC Pre-treatment: Capacitor is stored at 85±2ºC for 1 hour and then placed at room condition 1 for 24±2 hours before measurement. Terminal Strength Tensile Lead wire or capacitor body shall not break. With the termination in its normal position, the specimen is held by its body in such a manner that the axis of the termination is vertical; a tensile force of 10 N is applied to the termination in the direction of its axis and acting in a direction away from the body of the specimen. Bending Lead wire or capacitor body shall not break. With the termination in its normal position, the specimen is held by its body in such a manner that the axis of the termination is vertical; a mass force of 5 N is then suspended from the end of the termination. The body of the specimen is then inclined within a period of 2 to 3 seconds, through an angle of approximately 90° in the vertical plane and then resumed to its initial position over the same period of time; this operation constitutes one bend. One bend immediately followed by a second bend in the opposite direction. 1 “Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions cont'd Item Specification Test Method Solderability Lead wire should have a uniform coating of solder in the axial direction and over 3/4 of its circumference. The lead wire of the capacitor is dipped into molten solder for 5±0.5 seconds. The depth of immersion is up to 1.5 mm (+5/−0 mm) from the root of lead wires. Solder Temperature: Lead free solder (Sn-3Ag – 0.5Cu) 245°C ±5°C. Soldering Effect (Non-Preheat) Appearance No visual defect As shown in the figure below, the lead wires are immersed in molten solder up to 1.5 mm (+5/−0 mm) from the end of the epoxy meniscus (root of lead wire). Duration/Solder Temperature: 3.5±0.5 seconds/350°C ±10°C or 10±1 seconds/260°C ±5°C Molten Solder 1.5 to 2.0 mm CapacitorThermal Screen Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and then placed at room condition 1 for 24±2 hours before initial measurements. Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1. IR 1,000 MΩ Dielectric Strength Per item 1 Capacitance Y5P, Y5U and Y5V: Within ±10% SL: Within ±2.5% or ±0.25 pF, whichever is larger. Soldering Effect (Preheat) Appearance No visual defect Capacitor is stored at 120°C +0/−5°C for 60 +0/−5 seconds. Then, as shown in the figure below, the lead wires are immersed in molten solder up to 1.5 mm (+5/−0mm) from the end of the epoxy meniscus (root of lead wire). Duration/Solder Temperature: 7.5+0/−1 seconds/260°C ±5°C Molten Solder 1.5 to 2.0 mm CapacitorThermal Screen Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and then placed at room condition 1 for 24±2 hours before initial measurements. Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1. IR 1,000 MΩ Dielectric Strength Per item 1 Capacitance Y5P, Y5U and Y5V: Within ±10% SL: Within ±2.5% or ±0.25 pF, whichever is larger. Biased Humidity Appearance No visual defect Steady State Humidity: Load Humidity: Capacitance Temperature Characteristics Capacitance Change Y5P Within ±10% Y5U Within ±20% Y5V Within ±30% SL Within ±2.5% or ±0.25 pF, whichever is larger. 90 to 95% humidity at 40°C ±2°C for 500±12 hours. Post Treatment: Capacitor is stored for 1 to 2 hours at room condition 1. 90 to 95% humidity at 40°C ±2°C for 500±12 hours with full rated voltage applied. Post Treatment: Capacitor is stored for 1 to 2 hours at room condition 1. DF Y5P and Y5U: 5.0% maximum Y5V: 7.5% maximum Q SL: Less than 30 pF: Q ≥ 100+10×C/3 More than 30 pF: Q ≥ 200 C = Nominal capacitance IR Y5P, Y5V and Y5U: 3,000 M Ω minimum SL: 1,000 MΩ minimum Dielectric Strength No failures 1 “Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions cont'd Item Specification Test Method High Temperature Life Appearance No visual defect Impulse Voltage: Each individual capacitor is subjected to three 8 kv impulses prior to life testing. PP U PR U Vp 0.9Vp 0.5Vp Voltage tr td Time td (uS) tr (uS) 1.2 1.5 Cx (uF) 0.01 0.1 Capacitors are placed in a circulating air oven for a period of 1,000 hours. The air in the oven is maintained at a temperature of 125°C ±2°C throughout the test. The capacitors are subjected to AC 680 Vrms. Each hour the voltage is increased to AC 1,000 Vrms for 0.1 seconds. Capacitance Change Y5P, Y5V and Y5U: Within ±20% SL: Within ±3 or ±0.3 pF, whichever is larger. IR 3,000 MΩ minimum SL: 1,000 MΩ minimum Dielectric Strength No failures Flame Test The capacitor flame extinguishes as follows: Cycle Time 1 ~ 4 30 seconds maximum 5 60 seconds maximum The capacitor is exposed to a flame for 15 seconds and then removed for 15 seconds. This test is repeated for 5 cycles. Capacitor Flame 38 127 20º Gas Burner (Unit:mm) Active Flammability The cheesecloth should not ignite. The capacitors are individually wrapped in at least one, but not more than two, complete layers of cheesecloth. They are then subjected to 20 discharges. The interval between successive discharges is 5 seconds. The VAC is maintained for 2 minutes after the last discharge. Tr VacS2 L3 L4 C2 C3 CX Ct Vt L1F R Oscilloscope C1, 2 1 μF ±10% C3 0.033 μF ±5% 10 kV L1-4 1.5 Mh ±20% 16A Rod core choke Cx Test capacitor R 100 ±2% VAC VR ±5% Ct 3 μF ±5% 10 kV VR Rated Voltage F Fuse, Rated 10A Vt Voltage applied to Ct Vx 5kV time 1 “Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions cont'd Item Specification Test Method Passive Flammability The burning time should not exceed 30 seconds. The tissue paper should not ignite. The capacitor under test is held into a flame and in a position which best promotes burning. Each specimen is exposed to the flame one time. 200 ±5mm About 8mm45º Test Specimen About 10mm Thick Board Tissue Time of exposure to flame: Length of flame: Gas burner length: Inside diameter: Outside diameter: Gas butane gas purity: 30 seconds 12±1 mm 35 mm minimum 0.5±0.1 mm 0.9 mm maximum 95% minimum Temperature Cycle Appearance No visual defect The capacitor is subjected to 5 temperature cycles. Temperature Cycle Step Temperature (°C) Dwell Time (minutes) Transition Time (minutes) 1 −40 +0/−3 30
2 Room temperature 3
3 125 +3/−0 30
4 Room temperature 3
Pre-treatment: Capacitor shall be stored at 85±2 for 1 hour then placed at room condition 1 for 24±2 hours. Post-treatment : Capacitor is stored for 1 to 2 hours at room condition1. Capacitance Temperature Characteristics Capacitance Change SL Within ±5% Y5P Within ±10% Y5U, Y5V Within ±20% DF/Q SL ≥30 pF: Q ≥ 350 <30 pF: Q ≥ 275 +5/2C C = Nominal capacitance Y5P DF ≤ 5% Y5U, Y5V DF ≤ 7.5% IR 3,000 MΩ minimum SL: 1,000 MΩ minimum Dielectric Strength No failures 1 “Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Soldering and Mounting Information Soldering: When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could reflow the solder joint between the lead and ceramic element and/or may result in thermal shocks that can crack the ceramic element. When soldering these capacitors with a soldering iron, it should be performed under the following conditions: T emperature of iron-tip: 400ºC maximum S oldering iron wattage: 50 W maximum S oldering time: 3.5 seconds maximum Cleaning (ultrasonic cleaning): To perform ultrasonic cleaning, observe the following conditions: R inse bath capacity: Output of 20 watts per liter or less R insing time: 5 minute maximum D o not vibrate the PCB/PWB directly E xcessive ultrasonic cleaning may lead to fatigue destruction of the lead wires Construction Detailed Cross Section Epoxy Encapsulation (0.4 mm Minimum cThickness, Pigment = Blue/UL 94 V-0) Lead Attach Solder (Sn96.5/Ag3/Cu0.5) Electrode (Ag – Glass Frit) Core Metal Barrier Layer Finish Layer Steel Cu 100% Sn (3-7 µm) Lead Wire Dielectric Material (BaTiO3) Lead Attach Solder (Sn96.5/Ag3/Cu0.5) Electrode (Ag – Glass Frit) Dielectric Material (BaTiO3)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Marking These capacitors shall be stamped or laser marked with KEMET's trademark, type designation, capacitor class, rated voltage, rated capacitance and capacitance tolerance codes. In addition, all devices are marked with the recognized approval mark and a date/lot code for traceability. Marking will be supplied either on one side or both sides of the encapsulated capacitor body. All marking shall be legible to allow for clear identification of the component. Marking appears in legible contrast. Illustrated below is an example of the marking format and content. (Two sided marking is limited to capacitors with body diameters ≤ 8.0 mm.) Single Sided UL approval mark VDE & ENEC approval marks IEC 60384-14 3rd (2005) Rated Capacitance (3 Numeric Characters) Capacitance Tolerance Code (1 Character) Capacitor Class and Rated Voltage KEMET ID Type Designation (2 Characters) Date/Lot Code (See Table Below) Double Sided Capacitor Class and Rated Voltage Front Back KEMET ID Type Designation (2 Characters) VDE & ENEC approval marks IEC 60384-14 3rd (2005) UL approval mark Date/Lot Code (See Table Below) Rated Capacitance (3 Numeric Characters) Capacitance Tolerance Code (1 Character) Date/Lot Code Explanation
6 C 6 1234
Last digit of year, e.g., 6 = 2016 Manufacturing Location Code Manufacturing Month: 1-9 = Jan - Sept A = October N = November D = December Last 4 digits of lot no.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Packaging Quantities Capacitor Body Diameter (mm) Body Diameter Code1 Bulk Bag (Loose) Ammo Pack (Carrier Tape) Component pitch on carrier tape 2 25.4 mm 7.0 0 500 pieces/bag 1,000 pieces/box 8.0 1 9.0 2 10.0 3 11.0 4 13.0 6 500 pieces/box14.0 7 15.0 8 1 The "Body Diameter Code" is located in the third character position of the ordering code. This code identifies the maximum diameter of the capacitor body in millimeters. For more information regarding the ordering code, see "Ordering Information" section of this document. 2 For details regarding component pitch on carrier tape, see "Ammo Pack Taping Format" and "Ammo Pack Taping Specifications" sections of this document.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Figure 1 - Ammo Pack Taping Format (10 mm Lead Spacing) L P2 P F e D H0 W1 W ØD0 Ød ℓ Table 3 – Ammo Pack Taping Specifications Lead Spacing 10 mm Lead Style Straight Preformed1 Item Symbol Dimensions (mm) Lead Spacing F 10.0±1.0 Component Pitch P 25.4±2 Sprocket Hole Pitch P0 12.7±0.3 Sprocket Hole Center to Component Center P2 12.7±1.5 Sprocket Hole Center to Lead Center P1 7.7±1.5 Body Diameter D See "Product Ordering Codes and Ratings" section of this document. Component Alignment (side/side ) ∆S 0±2.0 Carrier Tape Width W 18.0+1.0/−0.5 Sprocket Hole Position W1 9.0 ±0.5 Height to Seating Plane 2 (preformed leads 1) H 0 N/A 18.0 +2.0/−0 Height to Seating Plane 2 (straight leads) H 20.0+1.5/−1.0 N/A Lead Protrusion ℓ 2.0 maximum Diameter of Sprocket Hole D 0 4.0±0.2 Lead Diameter φd 0.55±0.1 Carrier Tape Thickness t1 0.6±0.3 Total Thickness (Carrier Tape, Hold-Down Tape and Lead) t2 1.5 maximum Component Alignment (front/back ) ∆h1 2.0 maximum ∆h2 2.0 maximum Cut Out Length L 11.0 maximum Hold-Down Tape Width W0 11.0 minimum Hold-Down Tape Position W2 1.5±1.5 Coating Extension on Leads (meniscus) e 3.0 maximum for straight lead; not to exceed the bend for preformed 1 lead configurations. Body Thickness T See "Product Ordering Codes and Ratings" section of this document. 1 Preformed (crimped) lead configurations include vertical kink and outside kink. See "Lead Configurations" and "Ordering Information" sections of this document for further details. 2 Also referred to as "lead length" in this document. T maximum Marking Side ∆h1 ∆h2 t2 t1
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) Application Notes: Storage and Operating Conditions: The insulating coating of these devices does not form an air and moisture-tight seal. Avoid exposure to moisture and do not use or store these devices in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt, or the like are present. Before cleaning, bonding or molding these devices, it is important to verify that your process does not affect product quality and performance. KEMET recommends testing and evaluating the performance of a cleaned, bonded or molded product prior to implementing and/or qualifying any of these processes. Store the capacitors where the temperature and relative humidity do not exceed 40 degrees Centigrade and 70% respectively. For optimum solderability, capacitor stock should be used promptly, preferably within 6 months of receipt. Working Voltage: Application voltage (Vp-p or Vo-p) must not exceed the voltage rating of the capacitor. Irregular voltages can be generated for a transient period of time when voltage is initially applied and/or removed from a circuit. It is important to choose a capacitor with a voltage rating greater than or equal to these irregular voltages. Operating Temperature and Self-Generating Heat: The surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. Be sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or similar current, it may self-generate heat due to dielectric loss. Temperature rise due to self-generated heating should not exceed 20°C (while operated at an atmosphere temperature of 25°C). Handling - Vibration and Impact: Do not expose these devices or their leads to excessive shock or vibration during use. FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT , WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR PARTIAL DISPERSION WHEN THE PRODUCT IS USED.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C 1068_X1_400 VAC_Y1_400 VAC • 1/13/2017 Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, 900 Series, Encapsulated, AH Type, X1 400 VAC/Y1 400 VAC (Industrial Grade) KEMET Electronic Corporation Sales Offi ces For a complete list of our global sales offi ces, please visit www.kemet.com/sales. Disclaimer All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation.