C767U103MZYDAA7301

KJY KEMET | Alldatasheet

Document overview

• PDF pages: 16

Technical content

1© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Built Into Tomorrow Overview KEMET’s C700 encapsulated radial leaded ceramic disc capacitors are specifically designed for interference- suppression AC line filtering applications. Having internationally recognized safety certifications, these capacitors are well-suited for applications that require keeping potentially disruptive or damaging line transients and EMI out of susceptible equipment. They are also an ideal solution when needing to suppress line disturbances at the source. Safety Certified Capacitors are classified as either X and/or Y capacitors. Class X capacitors are primarily used in line- to-line (across-the-line) applications. In this application, there is no danger of electric shock to humans should the capacitor fail, but could result in a risk of fire. The class Y capacitor is primarily used in line-to-ground (line by-pass) applications. In this application, failure of the capacitor could lead to danger of electric shock. With a working voltage of 440/400 VAC in line-to-line (Class X) and 300/250 VAC in line-to-ground (Class Y) applications, these safety capacitors meet the impulse test criteria outlined in IEC Standard 60384. Meeting subclass X1 and Y2 requirements, these devices are certified to withstand impulses up to 4 KV (X1) and 5 KV (Y2) respectively. These encapsulated devices also meet the flame test requirements outlined in UL Standard 94 V-0. Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Benefits

• Safety standard recognized (IEC 60384-14)
• Re liable operation up to 125°C
• Cl ass X1 440/400 VAC/Y2 300/250 VAC
• 5. 0 mm, 7.5 mm, 10 mm, and 12.5mm lead spacing
• Le ad(Pb)-free and RoHS Compliant
• Ha logen-free
• Ca pacitance offerings ranging from 100 pF up to 10 nF
• Av ailable capacitance tolerances of ±5%, ±10%, and ±20%
• Hi gh-reliability
• Pr eformed (crimped) or straight lead configurations
• No n-polar device, minimizing installation concerns
• En capsulation meets flammability standard UL 94 V-0

Applications

Typical applications include: Li ne-to-line (Class X) filtering

• Li ne-to-ground (Class Y) filtering
• An tenna coupling
• Pr imary and secondary coupling (switching power supplies)
• Li ne disturbances suppression (motors and motor controls, relays, switching power supplies and invertors)

2© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade)

Ordering Information

C7 8 1 U 103 M Y V D A A 7301 Ceramic Series Body Diameter Lead Spacing1,2,3 Spec. Capacitance Code (pF) Capacitance Tolerance Rated Voltage Dielectric/ Temp. Char. Design Lead Configuration 1,3 Failure Rate Packaging (C-Spec) C7 = Ceramic 700 0 = 7.0 mm 1 = 8.0 mm 2 = 9.0 mm 3 = 10.0 mm 4 = 11.0 mm 5 = 12.0mm 6 = 13.0 mm 7 = 14.0 mm 8 = 15.0 mm 9 = 16.0 mm 5 = 5.0 mm 7 = 7.5 mm 1 = 10.0 mm 2 = 12.5 mm U = Safety Two significant digits and Number of zeroes K = ±10% M = ±20% Y = X1 400 VAC/ Y2 250 VAC Z = X1 440 VAC/ Y2 300 VAC S = SL Y = Y5P W = Y5U V = Y5V D = Disc A = Straight B = Vertical Kink C = Outside Kink D = Inside Kink A = N/A See "Packaging C-Spec Ordering Options Table" below 1 Due to a high risk of arcing, "Inside Kink" lead configuration cannot be combined with the 5 mm lead spacing option. The "Inside Kink" option is only available on capacitors with lead spacing of 7.5 mm or greater. A potential for arcing may exist when combining the "Inside Kink" lead configuration with a 7.5 mm lead spacing option, especially in high humidity environments and/or when exposure to voltages and transients may impact creepage and clearance requirements. 2 Capacitor body diameter will limit available lead spacing and packaging options. See "Dimensions" and "Product Ordering Codes and Ratings" sections of this document to determine availability. 3 Bulk packaging lead length availability is dependent upon "Lead Configuration" and "Lead Spacing." See "Dimensions" section of this document to verify availability of a specific lead length option. For nonstandard lead length inquiries, please contact KEMET. Packaging C-Spec Ordering Options Table Packaging Type Lead Length (mm)2,3 Packaging Ordering Code (C-Spec) Reel See Note 2 7301 Ammo Pack 7317 Bulk Bag 3.5 ±1.0 WL35 5.0 ±1.0 WL50 25.0 mm Minimum WL25 1 For nonstandard lead length inquiries, please contact KEMET. 2 Lead length for ammo and reel pack packaging is defined by the H and H0 dimensions in Table 3.

3© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Lead Configurations Straight Vertical Kink Outside Kink Inside Kink1 e L F Ød D Maximum T Maximum L F 4.0 Maximum Ød D Maximum T Maximum L FF 5.0 Maximum Ød D Maximum T Maximum L F 5.0 Maximum Ød D Maximum T Maximum 1 Due to a high risk of arcing, the "Inside Kink" lead configuration option cannot be combined with 5 mm lead spacing ("S" dimension above). The "Inside Kink" option is only available on devices with lead spacing of 7.5 mm, 10 mm, or 12.5 mm. Dimensions – Millimeters Lead Configuration Lead Configuration Ordering Code1 F Lead Spacing Tolerance D T e Ød Lead Spacing2 Body Diameter2 Body Thickness Lead Meniscus Lead Diameter Straight A 5.0 ±1.0 See Table 1 - "Product Ordering Codes and Ratings" 3.0 maximum 0.60 ±0.1 7.5 10.0 12.5 Vertical Kink (Preformed) B 5.0 7.5 10.0 12.5 Outside Kink (Preformed) C 5.0 7.5 10.0 12.5 Inside Kink (Preformed) D 7.5 10.0 12.5 1 Lead Configuration is identified in the 13th character of the ordering code. See "Lead Configuration" and "Ordering Information" sections of this document for further details. 2 Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this document for further details.

4© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Approval Standard and Certification No. Safety Standard Standard No. Subclass Working Voltage Certificate No. TUV IEC 60384-14 X1 400 VAC R50466992 Y2 250 VAC TUV IEC 60384-14 X1 440 VAC R50466992 Y2 300 VAC UL CAN/CSA UL 60384-14 and E60384-14 X1 400 VAC E356389 Y2 250 VAC UL CAN/CSA UL 60384-14 and E60384-14 X1 440 VAC E356389 Y2 300 VAC These devices are TUV and UL recognized for antenna coupling and AC line-to-line (Class X) and line-to-ground (Class Y) applications per IEC60384-14 and UL 60384-14. Environmental Compliance These devices are Halogen-free and RoHS Compliant. They meet all requirements set forth by both EU and China RoHS directives.

5© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Table 1A – X1 400 Y2 250 Product Ordering Codes and Ratings (1) To properly complete ordering code, insert the one-digit numeric code to reflect required lead spacing: (Note that select capacitance values and packaging options may limit lead spacing availability. See table above to verify availability.) 5 = 5. 0 mm 7 = 7. 5mm 1 = 10 .0 mm 2 = 12 .5 mm (2) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this document, page 2, for further details.) A = St raight B = Ve rtical Kink C = Ou tside Kink D = In side Kink (3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this document, page 2, for available options. Dielectric/ Temp. Char. KE MET Part Number Ca pacitance Capacitance Tolerance Dimensions (mm) Lead SpacingBody Diameter (Maximum) Bo dy Thickness (Maximum) Lead Diameter Y5P C71(1)U101KYYD(2)A(3) 100 pF ±10% 8.0 5.0 0.60 ± 0.1 "5 mm 7.5 mm 10.0 mm 12.5 mm" C71(1)U151KYYD(2)A(3) 150 pF C71(1)U181KYYD(2)A(3) 180 pF C71(1)U221KYYD(2)A(3) 220 pF C71(1)U331KYYD(2)A(3) 330 pF C71(1)U471KYYD(2)A(3) 470 pF C72(1)U561KYYD(2)A(3) 560 pF 9.0C72(1)U681KYYD(2)A(3) 680 pF C73(1)U102KYYD(2)A(3) 1000 pF 10.0 Y5U C71(1)U102MYWD(2)A(3) 1000 pF ±20% 8.0 C72(1)U152MYWD(2)A(3) 1500 pF 9.0 C73(1)U222MYWD(2)A(3) 2200 pF 10.0 C74(1)U252MYWD(2)A(3) 2500 pF 11.0 C75(1)U332MYWD(2)A(3) 3300 pF 12.0 C76(1)U392MYWD(2)A(3) 3900 pF 13.0 C77(1)U472MYWD(2)A(3) 4700 pF 14.0 Y5V C71(1)U102MYVD(2)A(3) 1000 pF ±20% 8.0C71(1)U152MYVD(2)A(3) 1500 pF C72(1)U222MYVD(2)A(3) 2200 pF 9.0 C73(1)U252MYVD(2)A(3) 2500 pF 10.0C73(1)U332MYVD(2)A(3) 3300 pF C74(1)U392MYVD(2)A(3) 3900 pF 11.0 C75(1)U472MYVD(2)A(3) 4700 pF 12.0 C76(1)U502MYVD(2)A(3) 5000 pF 13.5 C77(1)U562MYVD(2)A(3) 5600 pF 14.0 C78(1)U682MYVD(2)A(3) 6800 pF 15.0 C79(1)U103MYVD(2)A(3) 10000 pF 16.0 7.5 mm 10.0 mm 12.5 mm Dielectric/ Temp. Char. KEMET Part Number Capacitance Capacitance Tolerance Body Diameter (Maximum) Body Thickness (Maximum) Lead Diameter Lead Spacing

6© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Table 1B – X1 440 Y2 300 Product Ordering Codes and Ratings (1) To properly complete ordering code, insert the one-digit numeric code to reflect required lead spacing: (Note that select capacitance values and packaging options may limit lead spacing availability. See table above to verify availability.) 5 = 5. 0 mm 7 = 7. 5mm 1 = 10 .0 mm 2 = 12 .5 mm (2) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section of this document, page 2, for further details.) A = St raight B = Ve rtical Kink C = Ou tside Kink D = In side Kink (3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this document, page 2, for available options. Dielectric/ Temp. Char. KE MET Part Number Ca pacitance Capacitance Tolerance Dimensions (mm) Lead SpacingBody Diameter (Maximum) Bo dy Thickness (Maximum) Lead Diameter Y5P C71(1)U101KZYD(2)A(3) 100 pF ±10% 8.0 5.0 0.60 ± 0.1 5 mm 7.5 mm 10.0 mm 12.5 mm C71(1)U151KZYD(2)A(3) 150 pF C71(1)U181KZYD(2)A(3) 180 pF C71(1)U221KZYD(2)A(3) 220 pF C71(1)U331KZYD(2)A(3) 330 pF C71(1)U471KZYD(2)A(3) 470 pF C72(1)U561KZYD(2)A(3) 560 pF 9.0C72(1)U681KZYD(2)A(3) 680 pF C73(1)U102KZYD(2)A(3) 1000 pF 10.0 Y5U C71(1)U102MZWD(2)A(3) 1000 pF ±20% 8.0 C72(1)U152MZWD(2)A(3) 1500 pF 9.0 C73(1)U222MZWD(2)A(3) 2200 pF 10.0 C74(1)U252MZWD(2)A(3) 2500 pF 11.0 C75(1)U332MZWD(2)A(3) 3300 pF 12.0 C76(1)U392MZWD(2)A(3) 3900 pF 13.0 C77(1)U472MZWD(2)A(3) 4700 pF 14.0 Y5V C71(1)U102MZVD(2)A(3) 1000 pF ±20% 8.0C71(1)U152MZVD(2)A(3) 1500 pF C72(1)U222MZVD(2)A(3) 2200 pF 9.0 C73(1)U252MZVD(2)A(3) 2500 pF 10.0C73(1)U332MZVD(2)A(3) 3300 pF C74(1)U392MZVD(2)A(3) 3900 pF 11.0 C75(1)U472MZVD(2)A(3) 4700 pF 12.0 C76(1)U502MZVD(2)A(3) 5000 pF 13.5 C77(1)U562MZVD(2)A(3) 5600 pF 14.0 C78(1)U682MZVD(2)A(3) 6800 pF 15.0 C79(1)U103MZVD(2)A(3) 10000 pF 16.0 7.5 mm 10.0 mm Dielectric/ Temp. Char. KEMET Part Number Capacitance Capacitance Tolerance Body Diameter (Maximum) Body Thickness (Maximum) Lead Diameter Lead Spacing

7© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions 1 “Room Condition” is defined as follows: Temperature: 20 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa. Item Specification Test Method Operating Temperature Range −55°C to +125°C Dielectric Strength Between lead wires No failures The capacitor shall not be damaged when 2,600 VAC (rms) is applied between the lead wires for 60 seconds. Body Insulation No failures The terminals (leads) of the capacitor shall be connected together. A metal foil is tightly wrapped around the body of the capacitor at a distance of about 3 to 4 mm from each terminal. The capacitor is then inserted into a container filled with metal balls approximately 1 mm in diameter. 2,600 VAC (rms) is applied for 60 seconds between the capacitor lead wires and metal balls. (charge/discharge current ≤ 50 mA). Metal Foil Metal Balls about 3 to 4 mmInsulation Resistance (IR) 10,000 MΩ minimum The insulation resistance shall be measured with 500 ±50 VDC applied after 60 ±5 seconds of charging. Capacitance Within specified tolerance Characteristic Frequency Voltage SL 1 MHz ±20%

5.0 Vrms Maximum

Y5P /Y5U/Y5V 1 MHz ±20% The measurement at reference temperature 25°C Dissipation Factor (DF) or Q Temperature Characteristics Specification Y5P DF ≤ 2.5% Y5U/Y5V DF ≤ 5.0% SL Q ≥ 300 Temperature Characteristics Temperature Characteristics Capacitance Change Y5P Within ±10% Y5U Within +22%/−56% Y5V Within +22%/−82% SL +350~1,000% A capacitance measurement is made at each step specified: Step Temperature 1 +25 ±2°C

2 Minimum operating temperature

3 +25 ±2°C

4 Maximum operating temperature

5 +25 ±2°C Pretreatment: Capacitor is stored at 85 ±2°C for 1 hour and then placed at room condition1 for 24 ±2 hours before measurement. Terminal Strength Tensile Lead wire or capacitor body shall not break. With the termination in its normal position, the specimen is held by its body in such a manner that the axis of the termination is vertical. A tensile force of 10 N is applied to the termination in the direction of its axis and acting in a direction away from the body of the specimen. Bending Lead wire or capacitor body shall not break. With the termination in its normal position, the specimen is held by its body in such a manner that the axis of the termination is vertical; a mass force of 5 N is then suspended from the end of the termination. The body of the specimen is then inclined within a period of 2 to 3 seconds, through an angle of approximately 90° in the vertical plane and then resumed to its initial position over the same period of time; this operation constitutes one bend. One bend immediately followed by a second bend in the opposite direction.

8© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions cont. Item Specification Test Method Soldering Effect (Non-Preheat) Appearance No visual defect As shown in the figure below, the lead wires are immersed in molten solder up to 1.5 mm (+5/−0 mm) from the end of the epoxy meniscus (root of lead wire). Duration/Solder Temperature: 3.5 ±0.5 seconds/350°C ±10°C or 10 ±1 seconds/260°C ±5°C Molten Solder 1.5 to 2.0 mm CapacitorThermal Screen Pretreatment: Capacitor is stored at 85°C ±2°C for 1 hour and then placed at room condition 1 for 24 ±2 hours before initial measurements. Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1. IR 1,000 MΩ Minimum Dielectric Strength Per item 1 Capacitance Within ±10% Y5P, Y5U and Y5V: within ±10% SL: within ±2.5% or ±0.25 pF, whichever is larger Biased Humidity Appearance No visual defect Steady State Humidity: Load Humidity: Capacitance Temperature Characteristics Capacitance Change Y5P Within ±10% Y5U Within ±15% Y5V Within ±30% SL Within ±5% 90 to 95% humidity at 40°C ±2°C for 500 ±12 hours. Post-treatment: Capacitor is stored for 1 to 2 hours at room condition 1. 90 to 95% humidity at 40°C ±2°C for 500 ±12 hours with full rated voltage applied. Post-treatment: Capacitor is stored for 1 to 2 hours at room condition 1. DF Y5V and Y5U: 7.5% maximum Y5P: 5% maximum Q Q ≥ 135 IR 3,000 MΩ minimum Dielectric Strength No failures High Temperature Life Appearance No visual defect Impulse Voltage: Each individual capacitor is subjected to three 5 kv impulses prior to life testing. PP U PR U Vp 0.9Vp 0.5Vp Voltage tr td Time td (uS) tr (uS) 1.2 1.5 Cx (uF) 0.01 0.1 Capacitors are placed in a circulating air oven for a period of 1,000 hours. The air in the oven is maintained at a temperature of 125°C ±2 throughout the test. The capacitors are subjected to 170% of Rated Voltage. Each hour the voltage is increased to AC 1,000 V rms for 0.1 seconds. Capacitance Change Y5P, Y5U within ±20% Y5V within ±30% IR 3,000 MΩ minimum SL: 1,000 MΩ minimum Dielectric Strength No failures 1 “Room Condition” is defined as follows: Temperature: 20 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

9© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Table 2 – Performance & Reliability: Test Methods and Conditions cont. Item Specification Test Method Flame Test The capacitor flame extinguishes as follows: Cycle Time 1 ~ 4 30 seconds maximum 5 60 seconds maximum The capacitor is exposed to a flame for 15 seconds and then removed for 15 seconds. This test is repeated for 5 cycles. Capacitor Flame 38 127 20º Gas Burner (Unit:mm) Active Flammability The cheesecloth should not ignite. The capacitors are individually wrapped in at least one, but not more than two, complete layers of cheesecloth. They are then subjected to 20 discharges. The interval between successive discharges is 5 seconds. The VAC is maintained for 2 minutes after the last discharge. Tr VacS2 L3 L4 C2 C3 CX Ct Vt L1F R Oscilloscope C1, 2 1 μF ±10% C3 0.033 μF ±5% 10 kV L1-10 1.5 mH ±20% 16 A Rod core choke Cx Test capacitor R 100 ±2% Ω VAC VR ±5% Ct 3 μF ±5% 10 kV VR Rated Working Voltage F Fuse, Rated 10A Vt Voltage applied to C t Vx 5kV time Passive Flammability The burning time should not exceed 30 seconds. The tissue paper should not ignite. The capacitor under test is held into a flame and in a position which best promotes burning. Each specimen is exposed to the flame once. 200 ±5mm About 8mm45º Test Specimen About 10mm Thick Board Tissue Time of Exposure to Flame: 30 seconds Length of Flame: 12 ±1 mm Gas Burner Length: 35 mm minimum Inside Diameter: 0.5 ±0.1 mm Outside Diameter: 0.9 mm maximum Gas Butane Gas Purity: 95% minimum 1 “Room Condition” is defined as follows: Temperature: 20 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

10© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Soldering and Mounting Information Soldering: When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could reflow the solder joint between the lead and ceramic element and/or may result in thermal shocks that can crack the ceramic element. When soldering these capacitors with a soldering iron, it should be performed under the following conditions: Te mperature of iron-tip: 400°C maximum

• So ldering iron wattage: 50 W maximum
• So ldering time: 3.5 seconds maximum Cleaning (ultrasonic cleaning): To perform ultrasonic cleaning, observe the following conditions: Ri nse bath capacity: output of 20 watts per liter or less
• Ri nsing time: 5 minute maximum
• Do n ot vibrate the PCB/PWB directly
• Ex cessive ultrasonic cleaning may lead to fatigue destruction of the lead wires Construction Detailed Cross SectionEpoxy Encapsulation (0.2 mm Minimum Thickness, Pigment = Blue/UL 94 V-0) Lead Attach Solder (Sn97/Ag3 Sn99.3/Cu0.7) Lead Attach Solder (Sn97/Ag3 Sn99.3/Cu0.7) Electrode (Ag/Cu) Core Metal Barrier Layer Finish Layer Steel Cu 100% Sn (3-7 µm) Lead wire Electrode (Ag/Cu) Dielectric material (BaTiO3) Dielectric material (BaTiO3)

11© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Marking These capacitors shall be laser marked with KEMET's trademark, type designation, capacitor class, rated voltage, rated capacitance, and capacitance tolerance codes. In addition, all devices are marked with the recognized approval mark and a date/lot code for traceability. Marking will be supplied on one side of the encapsulated capacitor body. All marking shall be legible to allow for clear identification of the component. Marking appears in legible contrast. Illustrated below is an example of the marking format and content. UL approval markApproval Mark Rated Capacitance (3 Numeric Characters) Capacitance Tolerance Code (1 Character) Capacitor Class and Rated Voltage KEMET Trademark Type Designation (3 Characters) Date/Lot Code (See Table Below) Date/Lot Code e.g., 9D (December 2019, Taiwan)

9 D -

Last digit of year, e.g., 3 = 2013 Manufacturing Month: 1-9 = Jan - Sept O = October N = November D = December Manufacturing Location Code (blank): Taiwan C: Dongguan

12© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Packaging Quantities Capacitor Body Diameter (mm) Body Diameter Code1 Bulk Bag (Loose) Lead Length (WL25) Cut Lead Length (WL35, WL50, WL10) 7.0 0 200 pieces/bag 500 pieces/bag 8.0 1 9.0 2 10.0 3 11.0 4 12.0 5 13.0 6 14.0 7 15.0 8 16.0 9 1 The "Body Diameter Code" is located in the third character position of the ordering code. This code identifies the maximum diameter of the capacitor body in millimeters. For more information regarding the ordering code, see "Ordering Information" section of this document. Lead Spacing Body Diameter (mm) Pitch (Carrier Tape) Body Diameter Code Reel (7301) Ammo Pack (7317) 5 ≤ 12.0 12.7 0 - 5 2,000 pieces/reel 1,000 pieces/box 12.0 < D ≤ 16.0 25.4 6 - 9 1,000 pieces/reel 750 pieces/box 7.5 ≤ 12.0 12.7 0 - 5 2,000 pieces/reel 1,000 pieces/box 12.0 < D ≤ 15.0 25.4 6 - 8 1,000 pieces/reel 750 pieces/box ≥ 16.0 9 750 pieces/reel 750 pieces/box 10 ≤ 10 25.4 0 - 3 1,000 pieces/reel 1,000 pieces/box ≥ 11 4 - 9 750 pieces/reel 750 pieces/box 12.5 ≤ 9 25.4 0 - 2 1,000 pieces/reel 500 pieces/box ≥ 10 3 - 9 500 pieces/reel 500 pieces/box

13© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Figure 1 - Ammo/Reel Pack Taping Format 5 mm and 7.5 mm Lead Spacing: L P2 P F e D W ØD0 Ød ℓ 5 mm, 7.5 mm, 10 mm and 12.5 mm Lead Spacing: L P2 P F e D W ØD0 Ød ℓ Table 3 – Ammo/Reel Pack Taping Specifications 1 Preformed (crimped) lead configurations include vertical kink, outside kink, and inside kink. See "Lead Configurations" and "Ordering Information" sections of this document for further details. 2 Also referred to as "lead length" in this document. For All Lead Spacing: T maximum Marking Side ∆h1 ∆h2 t2 t1 H0H Lead Spacing 5 mm 7.5 mm 10 mm 12.5 mm Lead Style Straight Preformed 1 Straight Preformed 1 Straight Preformed 1 Straight Preformed 1 Item Symbol Dimensions (mm) Sprocket Hole Center to Sprocket Hole Center to Body Diameter D See "Product Ordering Codes and Ratings" section of this document. Component Alignment (side/side) ∆S 0 ±2.0 Carrier Tape Width W 18.0 +1.0/−0.5 Sprocket Hole Position W1 9.0 ±0.5

14© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Table 3 – Ammo Pack Taping Specifications cont. 1 Prefromed (crimped) lead configurations include vertical kink and outside kink. See "Lead Configurations" and "Ordering Information" sections of this document for further details. 2 Also referred to as "lead length" in this document. Application Notes: Storage and Operating Conditions: The Insulating coating of these devices does not form an air and moisture tight seal. Avoid exposure to moisture and do not use or store these devices in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are present. Before cleaning, bonding or molding these devices, it is important to verify that your process does not affect product quality and performance. KEMET recommends testing and evaluating the performance of a cleaned, bonded or molded product prior to implementing and/or qualifying any of these processes. Store the capacitors where the temperature and relative humidity do not exceed 40 degrees centigrade and 70% respectively. For optimum solderability, capacitor stock should be used promptly, preferably within 6 months of receipt. Working Voltage: Application voltage (Vp-p or Vo-p) must not exceed the voltage rating of the capacitor. Irregular voltages can be generated for a transient period of time when voltage is initially applied and/or removed from a circuit. It is important to choose a capacitor with a voltage rating greater than or equal to these irregular voltages. Lead Spacing 5 mm 7.5 mm 10 mm 12.5 mm Lead Style Straight Preformed 1 Straight Preformed 1 Straight Preformed 1 Straight Preformed 1 Item Symbol Dimensions (mm) Height to Seating Plane 2 Height to SeatingPlane 2 Lead Protrusion ℓ 2.0 maximum Diameter of Sprocket Hole D0 4.0 ±0.2 Lead Diameter φd 0.6 ±0.1 Carrier Tape Thickness t1 0.6 ±0.3 Total Thickness (Carrier Tape, Hold- Down Tape and Lead) t2 1.5 maximum Component Alignment (front/back ) ∆h1 2.0 maximum ∆h2 Cut Out Length L 11.0 maximum Hold-Down Tape Width W0 10.0 minimum Hold-Down Tape Position W2 3.0 maximum Coating Extension on Leads (meniscus) e 3.0 maximum for straight lead; not to exceed the bend for preformed1 lead configurations. Body Thickness T 8.0 maximum

15© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) Application Notes (cont.): Operating Temperature and Self-Generating Heat: The surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. Be sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or similar current, it may self-generate heat due to dielectric loss. Temperature rise due to self-generated heating should not exceed 20°C (while operated at an atmosphere temperature of 25°C). Handling - Vibration and Impact: Do not expose these devices or their leads to excessive shock or vibration during use. FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT , WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR PARTIAL DISPERSION WHEN THE PRODUCT IS USED.

16© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard C1 103_KJY • 1/24/2023 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com Radial Leaded Ceramic Disc Capacitors Safety Standard Recognized, C700, Encapsulated, KJY Type, X1 440/400 VAC/Y2 300/250 VAC (Industrial Grade) KEMET Electronics Corporation Sales Offi ces For a complete list of our global sales offi ces, please visit www.kemet.com/sales. Disclaimer All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation.