C7942CA-02 HAMAMATSU | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Features

/K6C Non-destructive inspection /K6C Digital X-ray photography

Applications

/K6C C7942CA-02: 2400 × 2400 pixels C7943CA-02: 1248 × 1248 pixels /K6C Digital output (12-bit) /K6C High-speed imaging: C7942CA-02: 2 frames/s (single operation) 9 frames/s (4 × 4 binning) C7943CA-02: 7 frames/s (single operation) 30 frames/s (4 × 4 binning) /K6C Low noise and wide dynamic range /K6C Compact package /K6C Easy use IMAGE SENSOR Flat panel sensor Acquire digital X-ray image in real time and 170 & 176 mm diagonal size C7942CA-02, C7943CA-02 AMP ARRAY No. 1 VERTICAL SHIFT REGISTER TIMING PULSE GENERATOR OSCILLATOR ExtTrgGrb PIXEL NUMBER Vsync Hsync Pclk A/D IntExt BINNING (bin0, bin1) EXTERNAL POWER SUPPL Y A.vdd, D.vdd, V (±7.5) (not attached) AMP ARRAY No. 8 PHOTODIODE ARRAY Note: Signals are read out in order of pixel number. BUFFER AMP BUFFER AMP PROCESSING AMP PROCESSING AMP 57600005759999 24002339 480047992401 SCINTILLATOR (120 × 120 mm) BIAS GENERATOR ExtTrgLemo FIFO A/D FIFO VIDEO OUTPUT (12 BIT DIGITAL) KACCC0216EB I Block diagram (C7942CA-02) C7942CA-02 is a lightweight and compact flat panel sensor consisting of a sensor board and a control board. The sensor board also has 8 charge-sensitive amplifier arrays each having 300 ch amplifiers with a horizontal shift register. Analog video signals are amplified as the charge on each video line by 2400 ch charge amplifiers with CDS (Correlated Double Sampling) circuits added, and are output each of 8 amplifier arrays. The control board converts the analog video signal into a 12-bit digital signal and outputs it to an external frame grabber through the 12-bit parallel port.

Flat panel sensor C7942CA-02, C7943CA-02 I General ratings Parameter C7942CA-02 C7943CA-02 Unit Pixel size 50 × 50 100 × 100 µm Photodiode area 120 × 120 124.8 × 124.8 mm Number of pixels 2400 × 2400 1248 × 1248 pixels Number of active pixels 2240 × 2344 1216 × 1220 pixels Readout Charge amplifier array - Video output (Data1 - 12) RS-422 (differential) 12 bit - Output data rate 15.15 MHz Synchronous signal (Vsync, Hsync, Pclk) RS-422 (differential) - bin0/1, ExtTrgGrb, ExtTrgLemo, IntExt TTL - Scintillator CsI - I Absolute maximum ratings (Ta=25 °C) Parameter Symbol Value Unit Supply voltage for digital circuitry (+5 V) D.vdd +6.0 V Supply voltage for analog circuitry (+5 V) A.vdd +6.0 V Supply voltage for analog circuitry (±7.5 V) V(±7.5) ±12 V Input voltage (bin0/1, ExtTrgGrb, ExtTrgLemo, IntExt) Vin 0 to 6.0 V Operating temperature * 1 Topr 0 to +35 °C Storage temperature * 1 Tstg 0 to +50 °C *1: No condensation Frame rate (single operation) Sf (int) 1.9 2 - 6.65 7 - frames/s Frame rate (2 × 2 binning) - 4 - - 15 - frames/s Frame rate (4 × 4 binning) - 9 - - 30 - frames/s Frame rate external (single operation ) Sf (ext) - Sf (int) to 0.1 - - Sf (int) to 0.1 - frames/s Noise (rms) * 2 N (rms) - 1100 - - 2300 - electrons Saturation charge Csat - 2.2 - - 10 - M electrons Sensitivity * 3 S 20 25 - 22.4 28 - LSB/mR Resolution * 4 Reso 6 8 - 4 5 - line pairs/mm Dynamic range - 2000 - - 4300 - - Defect line * 5 - - - 20 - - 10 lines Output offset * 6 - - 65 200 - 65 200 LSB *2: Internal trigger mode, single operation *3: at 80 kVp without filter *4: Spatial frequency at CTF=5 % *5: A defect line is a horizontal or vertical line containing 4 or more pixels that produce less than 1/8 of the average output from surrounding pixels and are formed continuously from the opposite side of an amplifier array or a vertical shift register. Without a couple of adjacent defect line. *6: Average of all effective pixels in single operation at Sf (int) Note: X-ray energy range is 20 k to 100 kVp. I Resolution KACCB0135EA 0123456789 1 0 SPATIAL FREQUENCY (line pairs/mm) CTF (%) 100 C7942CA-02C7943CA-02

Flat panel sensor C7942CA-02, C7943CA-02 I Timing chart T o acquire images through an image grabber board, write parameters in the software program or parameter file by referring to the following timing chart and description. KACCC0362EA

1 FRAME

All pulses are counted in the “High” period of Hsync+ All pulses are counted at the riging edge of Pclk+. The effective video output is only included in the “Phe” period. LAST ROW Vsync+ (GRABBER) Vsync+ (GRABBER) Hsync+ (GRABBER) Hsync+ (GRABBER) Pclk+ (GRABBER) Pulse C7942CA-02 C7943CA-02Parameter 1 × 1 2 × 2 4 × 4 1 × 1 2 × 2 4 × 4 Effective line 2344 1172 586 1220 610 305He Dummy line 56 28 14 28 14 7 Effective pixel 2240 1120 560 1216 608 304Phe Dummy pixel 160 80 40 32 16 8 Phd 526 1726 2326 334 958 1270 Pg 21 21 21 27 27 27 Note: “He” is the Hsync count. Phe, Phd and Pg are the Pclk count. KACCC0369EA RECOMMENDATION: 50 % OF FRAME TIME From Tmin to Tmax Tvd ExtTrgLemo ExtTrgGrb (TTL) Vsync+ (RS-422) Hsync+, Pclk+ and Data 1-12 are the same as internal trigger mode.

  • Tmin is defined as 1/Sf (int).
  • Tmax is defined as the reciprocal of the minimum value of Sf (ext).
  • Tvd=390 µs (C7942CA-02) 210 µs (C7943CA-02) I External trigger mode T o acquire images in external trigger mode, input an external trigger pulse as shown below. When the time Tvd has passed after the rising edge of the external trigger pulse, synchronous signals and video signals are output.

Flat panel sensor C7942CA-02, C7943CA-02 I System requirements T o operate C7942CA-02 and C7943CA-02 Flat Panel Sensors at full performance, the following system and peripherals are required.

  • PC: IBM compatible PC running on Windows XP
  • Digital frame grabber card: Monochrome 16 bits or more, pixel clock 16 MHz or more, RS-422 interface synchronous signal (See the frame grabber manual.) The National Instruments IMAQ PCI-1424 (NI parts No. 777662-01) frame grabber with optional memory 64 MB (NI parts No. 920130-64) has been verified to successfully acquire 12-bit digital images from both C7942CA-02 and C7943CA-02. The IMAQ PCI-1422 (NI parts No. 777959-01) also acquires satisfactory images from C7943CA-02. Y ou can utilize the demonstration software that comes with the frame grabber as a simple viewer, to acquire and save an image. T o do so, refer to the frame grabber user’s guide for how to use the camera information file for the demonstration software. Please use of a series power supply. (Avoid using a switching power supply.) A power cable (terminated with an FGG.2B.307.CLAD92Z plug at one end and open at the other end; 2 m; see Table 2.), an external trigger cable (terminated with an FFA.OS.302.CLAC37 plug at one end and open at the other end; 5 m; see table 3.) and an earth cable (AWG 18; 4 m) comes supplied with C7942CA-02 and C7943CA-02. An optional frame grabber cable for interface with the 36-pin receptacle (see Table 1) on C7942CA-02 and C7943CA-02 is also available for synchronous signal input, video output and external control. The voltages described above are specified at the flat panel sensor side. The impedance of the power cable attached with the flat panel sensor is low enough but it causes 0.1 V approx. drop. Therefore the voltage at the power source side should be set 0.1 V higher than the voltage specified above. Install a noise filter on the AC power input line to prevent surges on the AC line. To supply the synchronous signal through ExtTrgGrb, apply high level of TTL to ExtTrgLemo and IntExt, or leave them without connection. On the contrary, to use ExtTrgLemo, set high level to ExtTrgGrb and IntExt, or leave them without connection. The earth terminal must be connected to a stable earth point to eliminate noise from surroundings. Table 1: Pin assignment of 36-pin receptacle Pin No. Signal Pin No. Signal

1 Data12+ (MSB) 19 Data12- (MSB)

2 Data11+ 20 Data11-

3 Data10+ 21 Data10-

4 Data9+ 22 Data9-

5 Data8+ 23 Data8-

6 Data7+ 24 Data7-

7 Data6+ 25 Data6-

8 Data5+ 26 Data5-

9 Data4+ 27 Data4-

10 Data3+ 28 Data3-

11 Data2+ 29 Data2-

12 Data1+ (LSB) 30 Data1- (LSB)

13 bin0 (TTL) 31 GND 14 bin1 (TTL) 32 GND

15 ExtTrgGrb (TTL) 33 IntExt (TTL)

16 Vsync+ 34 Vsync-

17 Hsync+ 35 Hsync-

18 Pclk+ 36 Pclk-

Unless otherwise noted, signal level is RS-422. 36-pin receptacle: TX20A-36R-D2GF1-A1L made by JAE (Japan Aviation Electronics Industry, limited) Mating plug: TX20A-36PH1-D2P1-D1E made by JAE (Japan Aviation Electronics Industry, limited) Table 2: Power pin assignment and cable color Pin No. Color Signal 1 Brown +7.5 V

2 Red Analog GND

3 Orange -7.5 V

4 Yellow Analog GND

5 Green Analog +5 V

6 Blue Digital GND

7 Purple Digital +5 V

Table 3: External trigger pin assignment and cable color Pin No. Color Signal

1 Red ExtTrgLemo (TTL)

2 Black Signal GND

2-pin receptacle: ECP .0S.302.CLL made by LEMO S. A

Flat panel sensor C7942CA-02, C7943CA-02 I Connection Install the frame grabber board into the PC by the manufacturer’s instructions. When a general-purpose frame grabber board is used, binning or trigger operation for bin0, bin1, IntExt and ExtT rgGrb can be controlled with its digital I/O control. KACCC0217ED VIDEO OUTPUT (12 BIT DIGITAL) Vsync, Hsync, Pclk BINNING (bin0, bin1) IntExt ExtTrgGrb X-RAY SOURCE FRAME GRABBER MONITOR PC/AT (REAR VIEW) OS + ACQUISITION SOFTWARE VOLTAGE SOURCE [A. vdd, D. vdd, V (±7.5)] ExtTrgLemo C7942CA-02, C7943CA-02 CMOS FLAT PANEL SENSOR C794 *CA-02 Top cover is made of aluminum 1.0 mm thick. weight: 2.4 kg 198 d ACTIVE AREA a (0, 0) e ACTIVE AREA b SCINTILLATOR TO TOP COVER 8.3 * a C7942CA-02 112 C7943CA-02 121.6 b 117.2 122 c 33.5 31.1 d 22.9 20.5 e (2239, 2343) (1215, 1219) 150 * 27 * 28 4 46574337

15 DIGITAL OUT

  • ±0.5 mm (4 ×) M3 DEPTH 4 33 *127 * 165 * 17 * 200 c CMOS FLAT PANEL SENSOR C794 *CA-02 CMOS FLAT PANEL SENSOR C794*CA-02 EXT.TRG .POWER I Dimensional outline (unit: mm, tolerance: ±1 mm unless otherwise noted) KACCA0135ED

Flat panel sensor C7942CA-02, C7943CA-02 I Notice

  • Do not subject the Flat Panel Sensors to strong vibration or shock. (Strong shock such as drop impacts may cause permanent damage to these sensors.)
  • Users must take responsibility for implementing X-ray shielding safety measures to avoid the risk of X-ray exposure.
  • Data listed in this datasheet is defined at the time of shipment. Characteristics may vary somewhat due to exposure to X-rays so take proper coutermeasures such as making periodic image correction.
  • This product is warranted for a period of 12 months after the date of the shipment. The warranty is limited to make a replacement or repair of any defective product due to defects in workmanship or materials used in manufacture. The warranty does not cover loss or damage caused by natural disaster, misuse (including modifications and any use not complying with the environment, application, usage and storage conditions described in this datasheet), or total radiation dose over 1 million Roentgen (less than 100 kVp) even within the warranty period.
  • As described above, flat panel sensors have limited resistance to radiation. This must be taken into account when using a flat panel sensor under continuous irradiation (in-line non-destructive inspection, etc.) When using flat panel sensors in non-destructive inspection equipment, please contact us and provide information such as irradiation conditions. I Optional frame grabber cables Frame grabber Cable type No. Cable length Cable end Cable end A8406-31 5 m A8406-36 7 m A8406-37 10 mGeneral-purpose A8406-38 12 m open A8406-32 5 m A8406-33 7 m A8406-34 10 mIMAQ PCI-1424 *7 A8406-35 12 m TX20A-36PH1-D2P1-D1E *8 PCS-XE100MA+ *9 *7: Made by NI (National Instruments Corporation) *8: Made by JAE (Japan Aviation Electronics Industry, Limited) *9: Made by Honda Tsushin Kogyo Co. Ltd. Note: The detailed information for these optional cable is shown in the datasheet of A8406 series. HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184, www.hamamatsu.com Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741 Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2007 Hamamatsu Photonics K.K. Cat. No. KACC1098E09 May 2007 DN C7942CA-02, C7943CA-02 conforms to European EMC directives: EN61326 Class A.