DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Amplifi ers for infrared detector C4159/C5185 series C3757-02 Low noise amplifi ers for infrared detector (InSb, InAs, InAsSb, InGaAs, MCT, PbS, PbSe) www.hamamatsu.com 1 Absolute maximum ratings (Ta=25 °C) Parameter Value Unit Supply voltage 18.0 max. V Operating temperature 0 to +40 °C Storage temperature -20 to +70 °C Note: Absolute maximum ratings are the values that must not be exceeded at any time. If even one of the absolute maximum ratings is exceeded even for a moment, the product quality may be impaired. Always be sure to use the product within the absolute maximum ratings. Required power supply specifi cations

  • C4159 series: ±15 V ± 0.5
  • C5185 series: ±15 V ± 0.5
  • Current-carrying capacity: 1.5 times or more of amplifi er's maximum current consumption
  • Ripple noise: 5 mVp-p or less
  • Analog power supply only Recommended DC power supply: E3620A, E3630A (Agilent Technologies) Ringing Vri tr 5 V Output waveform when tr=40 μs and photosensitive area is ϕ0.6 mm Ringing Vri ≤ 1.5 V Oscillating cycle ≤ 3 cycles Incident light 10% 90% Ringing specifi cations KIRDC0090EA Instruction manual Power cable (one end with 4-pin connector for connection to amplifi er and the other end unterminated, 2 m) A4372-02 Accessories

Amplifi ers for infrared detector C4159/C5185 series, C3757-02 Amplifi ers for photovoltaic detectors (Typ.) Parameter C4159-01 C4159-04 C4159-05 C4159-06 C4159-07 Unit Applicable detector*1 *2 *3 Dewar type InSb (P5968-060, P5968-100) Dewar type InAsSb (P11120-901) Dewar type InSb (P5968-200) Dewar type InAs (P7163) TE-cooled type InAs (P10090-11/-21) Non-cooled type InAs (P10090-01) TE-cooled type InAsSb (P11120-201, P12691-201) Dewar type MCT (P9697-01/-02) Conversion impedance 108, 107, 106 (3 ranges switchable) 2 × 107, 2 × 106, 2 × 105 (3 ranges switchable) 108, 107, 106 (3 ranges switchable) 106, 105, 104 (3 ranges switchable) 106, 105, 104 (3 ranges switchable) V/A Frequency response (amp only, -3 dB) DC to 100 kHz*4 DC to 45 kHz DC to 15 kHz DC to 100 kHz DC to 100 kHz - Output impedance 50 50 50 50 50 Ω Maximum output voltage (1 kΩ load) +10 +10 +10 +10 +10 V Output offset voltage ±5 ±5 ±10 ±5 ±5 mV Equivalent input noise current* 5 (f=1 kHz) 0.15 (108, 107 range) 0.65 (106 range) 0.55 0.15 (108, 107 range) 0.65 (106 range) 61 0 pA/Hz1/2 Reverse voltage Limited to 0 V operation - External power supply*6 ±15 V Current consumption +30, -10 max. +30, -22 max. mA *1: These amplifi ers cannot operate multiple detectors. *2: Consult us before purchasing if you want to use with a detector other than listed here. *3: Consult us before purchasing if you want to use with a multi-element detector. *4: When connected to a detector, frequency response becomes 60 kHz or less depending on the detector active area. ( ϕ0.6 mm: 60 kHz or less, ϕ1 mm: 25 kHz or less) Ringing occurs in the output if the rise time tr (0 to 90%) of incident light is approximately 100 μs or less. The ringing becomes larger as the rise time becomes shorter. No ringing occurs when detecting sine-wave light. (For information on the ringing specifi cations, see page 2.) *5: Input resistance: 1 MΩ (C4159-01/-04/-05), 500 Ω (C4159-06/-07) *6: Recommended DC power supply (analog power supply): ±15 V Current capacity: More than 1.5 times the maximum current consumption Ripple noise: 5 mVp-p or less Note: Output noise voltage = Equivalent input noise current × Conversion impedance For information about accessories except for the amplifi ers, refer to our datasheet “Infrared detector accessories”.

Amplifi ers for infrared detector C4159/C5185 series, C3757-02 Amplifi ers for photoconductive detectors (Typ.)*10 Parameter C5185-02 C5185-03 C5185-04 C3757-02 Unit Applicable detector*7 *8 *11 Dewar type MCT, InSb (P6606 series) MCT (P3981/P2750 series) MCT (P3257-101/-30)*12 PbS, PbSe - Input impedance 5 5 5 10000 kΩ Voltage gain 66 (× 2000) 66 (× 2000) 66 (× 2000) 40 (× 100) dB Frequency response (amp only, -3 dB) 5 Hz to 250 kHz 5 Hz to 250 kHz 5 Hz to 250 kHz 0.2 Hz to 10 kHz - Detector bias current 5 mA, 10 mA, 15 mA (3 ranges switchable) 0.1 mA, 0.5 mA, 1 mA (3 ranges switchable) 20 mA, 25 mA, 30 mA (3 ranges switchable) Internal bias - Output impedance 50 50 50 50 Ω Maximum output voltage (1 kΩ load) ±10 ±10 ±10 ±10 V Equivalent input noise voltage (f=1 kHz) 2.6* 13 1.8*13 10*13 40 nV/Hz1/2 External power supply*9 ±15 ±15 ±15 ±15 V Current consumption +100, -30 max. +100, -30 max. +100, -30 max. +15, -15 max. mA Note: Output noise voltage = Equivalent input noise voltage × Voltage gain *7: These amplifi ers cannot operate multiple detectors. *8: Consult us before purchasing if you want to use with a detector other than listed here. *9: Recommended DC power supply (analog power supply): ±15 V Current capacity: More than 1.5 times the maximum current consumption Ripple noise: 5 mVp-p or less *10: Before purchasing, make sure the bias current to the detector matches the detector bias current specifi ed in the above table. *11: Consult us before purchasing if you want to use with a multi-element detector. *12: Preamp for P3257-25 available upon request *13: At detector bias current max. Amplifi er for InGaAs PIN photodiodes (Typ.) Parameter C4159-03 Unit Applicable detector*7 *8 InGaAs - Conversion impedance 107, 106, 105 (3 ranges switchable) V/A Frequency response (amp only, -3 dB) DC to 15 kHz - Output impedance 50 Ω Maximum output voltage (1 kΩ load) +10 V Output offset voltage ±5 mV Equivalent input noise current (f=1 kHz) 2.5 pA/Hz Reverse voltage Can be applied from external unit - External power supply*9 ±15 V Current consumption ±15 max. mA

Amplifi ers for infrared detector C4159/C5185 series, C3757-02 4-pin connector 60 IN POWER OUT HIGH MID LOW 24.5 39.5 11.5 Bias adjusting screw BNC connector BNC 21.2 PREAMPLIFIER BNC connector 4-pin connector 38.5 13.5 PREAMPLIFIER OUT IN POWER 12.5 Solder leads to these terminals. Note: Socket for lead attachment is not provided. PIN connections GND Detector Detector 12.5 35 37 60 IN POWER OUT HIGH MID LOW 24.5 26.2 39.5 11.5 Gain adjusting screw BNC connector PREAMPLIFIER 4-pin connector Offset voltage adjusting screw Note: Socket for lead attachment is not provided. Solder leads to these terminals. PIN connections GND Cathode Anode C5185-02/-03/-04 C3757-02 KIRDA0049EC KIRDA0048EB Dimensional outlines (unit: mm, tolerance unless otherwise noted: ±1) KIRDA0046EC

Cat. No. KIRD1011E15 Apr. 2015 DN Amplifi ers for infrared detector C4159/C5185 series, C3757-02 www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39) 02-93581733, Fax: (39) 02-93581741 China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866 Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always contact us for the delivery specification sheet to check the latest specifications. The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use. Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. Information described in this material is current as of April, 2015. A4372-02 KIRDA0196EB 2000 ± 100 2770 ± 1010 ± 3 Solder processing Connector: HR10-7P-4P (made by Hirose Electric) Shielded wire (4 conductors) ϕ11 ϕ4.8 ϕ1.1 As viewed from connector side Pin connectionPin no. -Vs Lead color Blue GND Black/white/blue stranded wireGND +Vs White Related information ∙ Disclaimer Precautions www.hamamatsu.com/sp/ssd/doc_en.html