C10900D HAMAMATSU | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

Four selectable scan modes Photodiode area: 124.8 × 124.8 mm C10900D www.hamamatsu.com The C10900D is a fl at panel sensor developed for CT and panoramic imaging. It operates in 4 selectable scan modes to capture X- ray images: “Fast mode” and “Partial mode” with a pixel size of 200 × 200 μm, and “Fine mode” and “Panoramic mode” with a pixel size of 100 × 100 μm. A single C10900D serves as the X-ray sensor for both CT and panoramic imaging. Features Applications Cone beam CT Digital radiography, etc. Four selectable scan modes with different number of active pixels and pixel sizes High-speed imaging: 280 frames/s (Panoramic mode) High sensitivity: 6000 LSB/mR Wide dynamic range Active area: Approx. 12 × 12 cm (1248 × 1248 pixels) 13-bit digital output (Fast mode, Partial mode) For assembly into equipment (supplied without case) Structure (Fast mode) The C10900D is comprised of a sensor board and a control board. Mounted on the sensor board is a CMOS image sensor chip made up of a two- dimensional photodiode array, row-scanning vertical shift register, and 8 charge amplifier arrays. Each charge amplifier array has a horizontal shift register and consists of 78 ch charge amplifiers with CDS circuit. CsI scintillator is directly deposited on the two-dimensional photodiode array. X-rays incident on the scintillator are converted to fluorescence, which then enters the two-dimensional photodiode array where electric charge is accumulated in each pixel according to the light intensity. The accumulated charge on each row is sequentially selected by the row-scanning vertical shift register, transferred to the amplifiers through the data line, and converted to a voltage signal. Then an analog signal is sent out from each amplifier array by scanning the horizontal shift register. The control board converts the analog signal into a 13-bit digital signal, which is then sent to a frame grabber board as a 13-bit parallel output through one port. This product is bare board type for installation into equipment and is not covered with a metal shielded case. See “Notice” for details on EMC. /K44/K29 /K56 /K65/K72/K74/K69/K63/K61/K6C /K73/K68/K69/K66/K74 /K72/K65/K67/K69/K73/K74/K65/K72 /K54/K69/K6D/K69/K6E/K67 /K70/K75/K6C/K73/K65 /K67/K65/K6E/K65/K72/K61/K74/K6F/K72 /K45/K78/K74/K54/K72/K67/K47/K72/K62 /K50/K69/K78/K65/K6C /K6E/K75/K6D/K62/K65/K72 /K56/K73/K79/K6E/K63 /K48/K73/K79/K6E/K63 /K50/K63/K6C/K6B /K41/K2F/K44 /K45/K78/K74/K65/K72/K6E/K61/K6C /K70/K6F/K77/K65/K72 /K73/K75/K70/K70/K6C/K79 /K41/K2E/K76/K64/K64/K2C /K44/K2E/K76/K64/K64 /K28/K6E/K6F/K74 /K61/K74/K74/K61/K63/K68/K65/K64/K29 /K50/K68/K6F/K74/K6F/K64/K69/K6F/K64/K65 /K61/K72/K72/K61/K79 /K77/K69/K74/K68 /K64/K69/K72/K65/K63/K74/K6C/K79 /K64/K65/K70/K6F/K73/K69/K74/K65/K64 /K43/K73/K49 /K73/K63/K69/K6E/K74/K69/K6C/K6C/K61/K74/K6F/K72 /K4E/K6F/K74/K65/K3A /K53/K69/K67/K6E/K61/K6C/K73 /K61/K72/K65 /K72/K65/K61/K64 /K6F/K75/K74 /K69/K6E /K6F/K72/K64/K65/K72 /K6F/K66 /K70/K69/K78/K65/K6C /K6E/K75/K6D/K62/K65/K72 /K2E /K42/K75/K66/K66/K65/K72 /K61/K6D/K70 /K42/K75/K66/K66/K65/K72 /K61/K6D/K70 /K50/K72/K6F/K63/K65/K73/K73/K69/K6E/K67 /K61/K6D/K70 /K50/K72/K6F/K63/K65/K73/K73/K69/K6E/K67 /K61/K6D/K70 /K31/K32 /K33/K38/K39/K33/K37/K36/K33/K38/K39/K33/K37/K35 /K36/K32/K34/K36/K32/K33 /K31/K32/K34/K38/K31/K32/K34/K37/K36/K32/K35 /K42/K69/K61/K73 /K67/K65/K6E/K65/K72/K61/K74/K6F/K72 /K46/K49/K46/K4F /K41/K2F/K44 /K46/K49/K46/K4F /K56/K69/K64/K65/K6F /K6F/K75/K74/K70/K75/K74 /K28/K31/K33/K2D/K62/K69/K74 /K64/K69/K67/K69/K74/K61/K6C/K29 /K43/K68/K61/K72/K67/K65 /K61/K6D/K70 /K61/K72/K72/K61/K79 /K4E/K6F/K2E /K31 /K28/K77/K69/K74/K68 /K68/K6F/K72/K69/K7A/K6F/K6E/K74/K61/K6C /K73/K68/K69/K66/K74 /K72/K65/K67/K69/K73/K74/K65/K72 /K2C /K37/K38 /K63/K68/K29 /K53/K65/K6E/K73/K6F/K72 /K62/K6F/K61/K72/K64 /K43/K6F/K6E/K74/K72/K6F/K6C /K62/K6F/K61/K72/K64 /K43/K68/K61/K72/K67/K65 /K61/K6D/K70 /K61/K72/K72/K61/K79 /K4E/K6F/K2E /K38 /K28/K77/K69/K74/K68 /K68/K6F/K72/K69/K7A/K6F/K6E/K74/K61/K6C /K73/K68/K69/K66/K74 /K72/K65/K67/K69/K73/K74/K65/K72 /K2C /K37/K38 /K63/K68/K29 /K49/K6E/K74/K45/K78/K74 /K47/K72/K62 /K52/K65/K73/K6F /K47/K72/K62 /K53/K63/K61/K6E /K47/K72/K62 /K49/K6E/K74/K45/K78/K74 /K49/K4F /K52/K65/K73/K6F /K49/K4F /K53/K63/K61/K6E /K49/K4F /K45/K78/K74/K54/K72/K67/K49/K4F /K4F/K73/K63/K69/K6C/K6C/K61/K74/K6F/K72 KACCC0487EA

Parameter Fast mode Partial mode Fine mode Panoramic mode Unit Pixel size 200 × 200 200 × 200 100 × 100 100 × 100 μm Photodiode area 124.8 × 124.8 mm Number of pixels (H × V) 624 × 624 1248 × 1248 pixels Number of active pixels (H × V) 608 × 616 608 × 310 1216 × 1232 1216 × 72 pixels Readout Charge amplifier array - Video output (Data1-13) LVDS (differential) 13-bit LVDS (differential) 12-bit - Output data rate 17.68 17.68 35.35 35.35 MHz Synchronous signal (Vsync, Hsync, Pclk) LVDS (differential) - ExtTrgGrb, IntExtGrb, ResoGrb, ScanGrb, ExtTrgIO, IntExtIO, ResoIO, ScanIO TTL - Scintillator Directly deposited CsI - Absolute maximum ratings (Ta=25 °C) Parameter Symbol Value Unit Supply voltage for digital circuitry (+5 V) D.vdd +6.0 V Supply voltage for analog circuitry (+5 V) A.vdd +6.0 V Input voltage (ExtTrgGrb, IntExtGrb, ResoGrb, ScanGrb, ExtTrgIO, IntExtIO, ResoIO, ScanIO) Vin 0 to 6.0 V Operating temperature *1 Topr 0 to +40 °C Storage temperature *1 Tstg -10 to +60 °C Incident X-ray energy - 90 kVp *1: No condensation Selectable scan modes Active area for each scan mode KACCC0483EA /K46/K61/K73/K74 /K6D/K6F/K64/K65/K3A /K28/K36/K30/K37/K2C /K36/K31/K35/K29/K3 /K46/K69/K6E/K65 /K6D/K6F/K64/K65/K3A /K28/K31/K32/K31/K35/K2C /K31/K32/K33/K31/K29 /K28/K30/K2C /K30/K29 /K4E/K75/K6D/K62/K65/K72 /K6F/K66 /K61/K63/K74/K69/K76/K65 /K70/K69/K78/K65/K6C/K73 /K46/K61/K73/K74 /K6D/K6F/K64/K65/K3A /K36/K30/K38 /KD7 /K36/K31/K36 /K28/K32/K30/K30 /KD7 /K32/K30/K30 /KB5 /K6D/K2F/K70/K69/K78/K65/K6C/K29/K3 /K46/K69/K6E/K65 /K6D/K6F/K64/K65/K3A /K31/K32/K31/K36 /KD7 /K31/K32/K33/K32 /K28 /K31/K30/K30 /KD7 /K31/K30/K30 /KB5 /K6D/K2F/K70/K69/K78/K65/K6C/K29 /K28/K36/K30/K37/K2C /K34/K36/K32/K29 /K28/K36/K30/K37/K2C /K36/K31/K35/K29 /K28/K30/K2C /K31/K35/K33/K29 /K28/K30/K2C /K30/K29 /K4E/K75/K6D/K62/K65/K72 /K6F/K66 /K61/K63/K74/K69/K76/K65 /K70/K69/K78/K65/K6C/K73 /K36/K30/K38 /KD7 /K33/K31/K30 /K28/K32/K30/K30 /KD7 /K32/K30/K30 /KB5 /K6D/K2F/K70/K69/K78/K65/K6C/K29 /K28/K30/K2C /K35/K38/K30/K29 /K28/K31/K32/K31/K35/K2C /K36/K35/K31/K29 /K28/K31/K32/K31/K35/K2C /K31/K32/K33/K31/K29 /K28/K30/K2C /K30/K29 /K4E/K75/K6D/K62/K65/K72 /K6F/K66 /K61/K63/K74/K69/K76/K65 /K70/K69/K78/K65/K6C/K73/K3A /K31/K32/K31/K36 /KD7 /K37/K32 /K28/K31/K30/K30 /KD7 /K31/K30/K30 /KB5 /K6D/K2F/K70/K69/K78/K65/K6C/K29 Fast mode, Fine mode Partial mode Panoramic mode Four scan modes are available with different number of active pixels and pixel sizes.

Parameter Symbol Min. Typ. Max. Unit Frame rate Sf(int) 33.2 35 - frames/s Noise (rms) *2 N(rms) - 2900 - electrons Saturation charge Csat - 10.5 - M electrons Sensitivity *3 S 4800 6000 - LSB/mR Resolution *4 Reso 2 2.5 - line pairs/mm Dynamic range - - 3600 - - Fast mode Parameter Symbol Min. Typ. Max. Unit Frame rate Sf(int) 66.5 70 - frames/s Noise (rms) *2 N(rms) - 2900 - electrons Saturation charge Csat - 10.5 - M electrons Sensitivity *3 S 4800 6000 - LSB/mR Resolution *4 Reso 2 2.5 - line pairs/mm Dynamic range - - 3600 - - Partial mode Parameter Symbol Min. Typ. Max. Unit Frame rate Sf(int) 16.1 17 - frames/s Noise (rms) *2 N(rms) - 1300 - electrons Saturation charge Csat - 2.3 - M electrons Sensitivity *3 S 2800 3500 - LSB/mR Resolution *4 Reso 3.6 4.5 - line pairs/mm Dynamic range - - 1700 - - Fine mode Parameter Symbol Min. Typ. Max. Unit Frame rate Sf(int) 266 280 - frames/s Noise (rms) *2 N(rms) - 1300 - electrons Saturation charge Csat - 2.3 - M electrons Sensitivity *3 S 2800 3500 - LSB/mR Resolution *4 Reso 3.6 4.5 - line pairs/mm Dynamic range - - 1700 - - *2: Internal trigger mode *3: At 80 kVp, acrylic filter 170 mm *4: Spatial frequency at CTF=5 % Note: X-ray energy range is 20 k to 90 kVp. Panoramic mode Resolution /K30/K31/K32/K33/K34 /K34 /K2E /K35 /K30/K2E/K35 /K31/K2E/K35 /K32/K2E/K35 /K33/K2E/K35 /K28/K54 /K61/K3D/K32/K35 /KB0/K43/K2C /K41/K2E/K76/K64/K64/K3D/K35/K2E/K30 /K56 /K2C /K44/K2E/K76/K64/K64/K3D/K35/K2E/K30 /K56/K29 /K53/K70/K61/K74/K69/K61/K6C /K66/K72/K65/K71/K75/K65/K6E/K63/K79 /K28/K6C/K69/K6E/K65 /K70/K61/K69/K72/K73/K2F/K6D/K6D/K29 /K43/K54/K46 /K28/K25/K29 /K30 /K31/K30/K30 /K39/K30 /K38/K30 /K37/K30 /K36/K30 /K35/K30 /K34/K30 /K33/K30 /K32/K30 /K31/K30 /K46 /K61/K73/K74 /K6D/K6F/K64/K65 /K50/K61/K72/K74/K69/K61/K6C /K6D/K6F/K64/K65 /K46/K69/K6E/K65 /K6D/K6F/K64/K65 /K50/K61/K6E/K6F/K72/K61/K6D/K69/K63 /K6D/K6F/K64/K65 KACCB0204EA

/K31 /K66/K72/K61/K6D/K65 /K28/K54 /K76/K63/K29 /K31/K73/K74 /K72/K6F/K77 /K32/K6E/K64/K72/K6F/K77 /K48/K65 /K45/K6E/K6C/K61/K72/K67/K65/K64/K76/K69/K65/K77 /K50/K68/K65 /K50/K67 /K50/K68/K65 /K50/K68/K64/K50/K68/K64 /K50/K68/K65 /K31/K73/K74 /K72/K6F/K77 /K32/K6E/K64/K72/K6F/K77 /K31/K73/K74 /K72/K6F/K77 /K32/K6E/K64/K72/K6F/K77 /K41/K6C/K6C /K70/K75/K6C/K73/K65/K73 /K61/K72/K65 /K63/K6F/K75/K6E/K74/K65/K64/K69/K6E /K74/K68/K65 /K93/K48/K69/K67/K68/K94 /K70/K65/K72/K69/K6F/K64/K6F/K66 /K48/K73/K79/K6E/K63/K2B/K2E /K41/K6C/K6C /K70/K75/K6C/K73/K65/K73 /K61/K72/K65 /K63/K6F/K75/K6E/K74/K65/K64/K61/K74 /K74/K68/K65 /K72/K69/K67/K69/K6E/K67 /K65/K64 /K67/K65 /K6F/K66 /K50/K63/K6C/K6B/K2B/K2E /K54/K68/K65 /K65/K66/K66/K65/K63/K74/K69/K76/K65 /K76/K69/K64/K65/K6F /K6F/K75/K74/K70/K75/K74 /K69/K73 /K6F/K6E/K6C/K79 /K69/K6E/K63/K6C/K75/K64/K65/K64 /K69/K6E /K74/K68/K65 /K93/K50/K68/K65/K94 /K70/K65/K72/K69/K6F/K64/K2E /K48/K73/K79/K6E/K63/K2B /K61/K72/K65 /K6F/K75/K74/K70/K75/K74 /K63/K6F/K6E/K74/K69/K6E/K75/K6F/K75/K73/K6C/K79 /K77/K68/K69/K6C/K65 /K56/K73/K79/K6E/K63/K2B /K69/K73 /K6C/K6F/K77 /K2E /K4C/K61/K73/K74 /K72/K6F/K77 /K56/K73/K79/K6E/K63/K2B /K28/K67/K72/K61/K62/K62/K65/K72/K29 /K56/K73/K79/K6E/K63/K2B /K28/K67/K72/K61/K62/K62/K65/K72/K29 /K48/K73/K79/K6E/K63/K2B /K28/K67/K72/K61/K62/K62/K65/K72/K29 /K48/K73/K79/K6E/K63/K2B /K28/K67/K72/K61/K62/K62/K65/K72/K29 /K50/K63/K6C/K6B/K2B /K28/K67/K72/K61/K62/K62/K65/K72/K29 /K54 /K76/K64/K70/K77/K44/K75/K6D/K6D/K79 /K6C/K69/K6E/K65/K73 To acquire images through a frame grabber board, write parameters in the software program or parameter file by referring to the following timing chart and description. KACCC0361EC Timing chart Internal trigger mode Parameters Fast mode Partial mode Fine mode Panoramic mode He Dummy line 0000 Effective line 616 310 1232 72 Dummy line 8 0 16 0 Phe Dummy pixel 8 8 16 16 Effective pixel 608 608 1216 1216 Dummy pixel 8 8 16 16 Phd 177 177 354 354 Pg 157 157 311 346 Note: “He” is the Hsync count. Phe, Phd and Pg are the Pclk count. Parameter Symbol Min. Typ. Max. Unit Defect line *5 - - - 8 lines Blemish *6 - - - 600 μm Non-uniformity of sensitivity *6 -- - 4 % Defect cluster *6 - Not allowed - Bright line output adjacent to a defect line *6 - - - 120 % Output offset *7 - - 65 200 LSB *5: A defect line is a horizontal or vertical line containing 4 or more cosecutive pixels located, that produce 1/8 of the average sensitivity of the surrounding pixels. *6: See P. 9, “Description of terms (Fine mode)” *7: Average of all effective pixels in single operation at Sf(int)

/K52/K65/K63/K6F/K6D/K6D/K65/K6E/K64/K61/K74/K69/K6F/K6E/K3A /K35/K30 /K25 /K6F/K66 /K66/K72/K61/K6D/K65 /K74/K69/K6D/K65 /K46/K72/K61/K6D/K65 /K74/K69/K6D/K65 /K28/K54 /K76/K63/K74/K6F /K54/K6D/K61/K78/K29 /K54/K76 /K64 /K54/K78/K72/K61/K79 /K54/K76 /K6C /K54 /K76/K63/K2D /K54 /K76/K64/K70/K77 /K45/K78/K74/K54 /K72/K67/K49/K4F /K45/K78/K74/K54 /K72/K67/K47/K72/K62 /K28/K54 /K54/K4C/K29 /K56/K73/K79/K6E/K63/K2B /K28/K4C /K56/K44/K53/K29 /K48/K73/K79/K6E/K63/K2B/K2C /K50/K63/K6C/K6B/K2B /K61/K6E/K64 /K65/K66/K66/K65/K63/K74/K69/K76/K65 /K76/K69/K64/K65/K6F /K6F/K75/K74/K70/K75/K74 /K61/K72/K65 /K74/K68/K65 /K73/K61/K6D/K65 /K61/K73 /K69/K6E/K74/K65/K72/K6E/K61/K6C /K74/K72/K69/K67/K67/K65/K72 /K6D/K6F/K64/K65/K2E /KB7 /K54/K6D/K61/K78 /K69/K73 /K64/K65/K66/K69/K6E/K65/K64 /K61/K73 /K74/K68/K65 /K72/K65/K63/K69/K70/K72/K6F/K63/K61/K6C /K6F/K66 /K74/K68/K65 /K6D/K69/K6E/K69/K6D/K75/K6D /K76/K61/K6C/K75/K65 /K6F/K66 /K53/K66 /K28/K65/K78/K74/K29/K2E /KB7 /K54/K78/K72/K61/K79 /K3D /K46/K72/K61/K6D/K65 /K74/K69/K6D/K65 /K2D /K54 /K76/K64 /K2D /K28/K54 /K76/K63/K2D /K54 /K76/K64/K70/K77/K29 /KB7 /K54 /K76/K6C /K3D /K46/K72/K61/K6D/K65 /K74/K69/K6D/K65 /K2D /K28/K54 /K76/K63/K2D /K54 /K76/K64/K70/K77/K29 KACCC0489EA (Typ.) Parameter Symbol Fast mode Partial mode Fine mode Panoramic mode Unit Vsync Delay time (only external trigger mode) Tvd 83 110 81 140 μs Cycle time (internal trigger mode) Tvc 28.5 14.2 56.7 3.56 ms Pulse width of Vsync+ in low period (internal trigger mode) Tvdpw 170 120 170 290 μs Note: The numbers of significant figures is two. (except Tvc) To acquire images in external trigger mode, input an external trigger pulse as shown below. When the time Tvd has passed after the rising edge of the external trigger pulse, synchronous signals and video signals are obtained. When used in synchronization with a pulsed X-ray source, X-rays should be irradiated during the Txray period. To operate the sensor in external trigger mode, set the frame rate in the range shown below. External trigger mode Mode Pin No. A17 (ExtTrgGrb) Pin No. B17 (IntExtGrb) Internal trigger mode - (Input signal is ignored) Low External trigger mode Rectangular signal (See the above figure.) High When selecting the trigger mode via the 40-pin receptacle, do no connect to the external I/O connector. Operating mode External I/O connector pin No. 40-pin receptacle pin No. Pin No. 1 (IntExtIO) Pin No. 2 (ExtTrgIO) Pin No. A17 (ExtTrgGrb), Pin No. B17 (IntExtGrb) Internal trigger mode Low - (Input signal is ignored) High or Open External trigger mode High Rectangular signal (See the above figure.) Scan mode Frame rate: Sf(ext) Unit Fast mode Sf(int) to 10 frames/sPartial mode Fine mode Panoramic mode Sf(int) to 50 frames/s Trigger mode selection Setting via 40-pin receptacle Frame rate range in external trigger mode Setting via external I/O connector

To operate the C10900D at full performance, the following system and peripherals are required. O PC: PC running on Windows XP O Frame grabber board: Monochrome 16 bits or more, pixel clock 15.15 MHz or more, LVDS interface synchronous signal

  • The voltages described above are specified at the flat panel sensor side.
  • Please use a low noise series power supply. (Avoid using a switching power supply.)
  • Install a noise filter on the AC power input line to prevent surges on the AC line.
  • Always ground the fixing plate to avoid the effects of noise from peripheral devices. The power cable, frame grabber board cable, earth cable, image acquisition software, and image processing libraries are exclude d from the flat panel sensor. System requirements Scan mode Pixel size Pin No. A15 (ResoGrb) Pin No. A16 (ScanGrb) Fast mode 200 μm High High Partial mode Low Fine mode 100 μm Low High Panoramic mode Low When selecting the scan mode via the 40-pin receptacle, do not connect to the external I/O connector. Scan mode Pixel size External I/O connector pin No. 40-pin receptacle pin No. No. 3 (ResoIO) No. 4 (ScanIO) Pin No. A15 (ResoGrb) Pin No. A16 (ScanGrb) Fast mode 200 μm High High High or OpenPartial mode Low Fine mode 100 μm Low High Panoramic mode Low Scan mode selection Setting via 40-pin receptacle Setting via external I/O connector

Pin No. Signal

1 Digital GND

2 Digital +5 V

3 Analog GND

4 Analog +5 V

5 Shield (Analog GND)

Power plug: 53259-0529 (Molex Japan Co., Ltd.) Power receptacle: 51067-0500 (Molex Japan Co., Ltd.) Pin No. signal Setting Function

1 IntExtIO (TTL) Low Internal trigger mode

High External trigger mode

2 ExtTrgIO (TTL) - Trigger signal Input under the external mode

3 ResoIO (TTL) Low Pixel size: 100 × 100 μm

High Pixel size: 200 × 200 μm

4 ScanIO (TTL) Low Panoramic mode/Partial mode

5 Reserved - -

6 Reserved - -

7 Reserved - -

8 Digital GND - Digital GND

8-pin receptacle 53048-0810 mode by Molex Japan Co., Ltd. Matins plug 51021-0800 made by Molex Japan Co., Ltd. Pin No. Signal Pin No. Signal A1 Data1+ (LSB) B1 Data1- (LSB) A2 Data2+ B2 Data2- A3 Data3+ B3 Data3- A4 Data4+ B4 Data4- A5 Data5+ B5 Data5- A6 Data6+ B6 Data6- A7 Data7+ B7 Data7- A8 Data8+ B8 Data8- A9 Data9+ B9 Data9- A10 Data10+ B10 Data10- A11 Data11+ B11 Data11- A12 Data12+ B12 Data12- A13 Data13+ (MSB) B13 Data13- (MSB) A14 Reserved B14 Reserved A15 ResoGrb (TTL) B15 GND A16 ScanGrb (TTL) B16 GND A17 ExtTrgGrb (TTL) B17 IntExtGrb (TTL) A18 Vsync+ B18 Vsync- A19 Hsync+ B19 Hsync- A20 Pclk+ B20 Pclk- Unless otherwise noted, signal level is LVDS. 40-pin receptacle: 8931E-040-178LF (KEL Corporation) Mating plug: 8925R-040-179F (KEL Corporation) Pins described “Reserved” are prepared for an extention of the future. Do not connect any signal or power or GND to this plug. Pin assignment of 40-pin receptacle Pin assignment of external I/O connector Power pin assignment

Install the frame grabber board into the PC by the manufacture’s instructions. When a general-purpose frame grabber board with I/O control is used, the trigger mode can be set by controlling IntExtGrb and ExtTrgGrb through the I/O line. The scan mode can be set by c ontrolling ResoGrb and ScanGrb. The trigger mode can also be set by controlling IntExtIO and ExtTrgIO via the external I/O connector. The scan mode can be set by controlling ResoIO and ScanIO. Connection example /K56/K69/K64/K65/K6F /K6F/K75/K74/K70/K75/K74 /K28/K31/K32/K2D/K62/K69/K74/K2F/K31/K33/K2D/K62/K69/K74 /K64/K69/K67/K69/K74/K61/K6C/K29 /K56/K73/K79/K6E/K63/K2C /K48/K73/K79/K6E/K63/K2C /K50/K63/K6C/K6B /K46/K72/K61/K6D/K65 /K67/K72/K61/K62/K62/K65/K72 /K62/K6F/K61/K72/K64 /K4D/K6F/K6E/K69/K74/K6F/K72/K50/K43/K2F/K41/K54 /K28/K52/K65/K61/K72 /K76/K69/K65/K77/K29 /K43/K31/K30/K39/K30/K30/K44 /K58/K2D/K72/K61/K79 /K73/K6F/K75/K72/K63/K65 /K4F/K62/K6A/K65/K63/K74 /K4F/K53 /K2B /K69/K6D/K61/K67/K65 /K61/K63/K71/K75/K69/K73/K69/K74/K69/K6F/K6E /K73/K6F/K66/K74/K77/K61/K72/K65 /K56/K6F/K6C/K74/K61/K67/K65 /K73/K6F/K75/K72/K63/K65 /K28/K41/K2E/K76/K64/K64/K2C /K44/K2E/K76/K64/K64/K29 /K49/K6E/K74/K45/K78/K74/K47/K72/K62 /K45/K78/K74/K54/K72/K67/K47/K72/K62 /K52/K65/K73/K6F/K47/K72/K62 /K53/K63/K61/K6E/K47/K72/K62 /K49/K6E/K74/K45/K78/K74/K49/K4F /K45/K78/K74/K54/K72/K67/K49/K4F /K52/K65/K73/K6F/K49/K4F /K53/K63/K61/K6E/K49/K4F KACCC0482EA Dimensional outline (unit: mm, tolerance: ±1 mm unless otherwise noted) KACCA0 40.3Active area 123.2 * 177 73.8 31.5 185 33 13.5 33.7 60 26 12.7 3135 168 Photodiode area 124.8 1414 48 36.522 Scintillator to top cover 2.5 The cover is made of carbon fiber (0.4 mm tickness) Weight: 1.2 kg * Fast mode / Fine mode 18.3 3.5 3.5 4.1 6.6 0.6 43.3 Photodiode area 124.8 10 10 8 Active area 121.6 KACCA0254ED

/K4E/K6F/K6E/K2D/K75/K6E/K69/K66/K6F/K6D/K69/K74/K79 /K6F/K66 /K73/K65/K6E/K73/K69/K74/K69/K76/K69/K74/K79 /K3D σ/K3A /K73/K74/K61/K6E/K64/K61/K72/K64 /K64/K65/K76/K69/K61/K74/K69/K6F/K6E /K6F/K66 /K31/K36 /KD7 /K31/K36 /K93/K58/K69/K6A/K94 /K78 /K3A /K61/K76/K65/K72/K61/K67/K65 /K76/K61/K6C/K75/K65 /K6F/K66 /K31/K36 /KD7 /K31/K36 /K93/K58/K69/K6A/K94 σ /K78 /KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7 /KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7 /KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7 /KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7 /KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7/KB7 /K31/K30 /K70/K69/K78/K65/K6C/K73 /K31/K30 /K70/K69/K78/K65/K6C/K73 /K31/K30 /K70/K69/K78/K65/K6C/K73 /K31/K30 /K50/K49/K58/K45/K4C/K53/K37/K35 /K70/K69/K78/K65/K6C/K73 /K37/K36 /K70/K69/K78/K65/K6C/K73/K37/K36 /K70/K69/K78/K65/K6C/K73/K37/K36 /K70/K69/K78/K65/K6C/K73/K37/K32 /K70/K69/K78/K65/K6C/K73 /K37/K35 /K70/K69/K78/K65/K6C/K73 /K37/K35 /K70/K69/K78/K65/K6C/K73 /K37/K31 /K70/K69/K78/K65/K6C/K73 /K31/K6D /K6D /K41/K63/K74/K69/K76/K65 /K61/K72/K65/K61 /K31/K6D /K6D /K31/K6D /K6D /K31/K6D /K6D /K41/K63/K74/K69/K76/K65 /K61/K72/K65/K61 /K31/K36 /K73/K65/K67/K6D/K65/K6E/K74/K73 /K31/K36 /K73/K65/K67/K6D/K65/K6E/K74/K73 16 × 16 segments are 16 × 16-divided active area excluded 1 mm from the whole edge. Xij is defined as the average sensitivity of each segment. Uniformity of sensitivity is calculated as following equation. Non-uniformity of sensitivity Description of terms (Fine mode) Length of pixel cluster which has less than 90 % of the average sensitivity of the surrounding pixels. Formed with more than 3 × 3 pixels which have less than 1/8 of the average sensitivity of the surrounding pixels. The relative sensitivity ratio “a/b” should be 120 % or less for both vertical and horizontal lines, where “a” and “b” are defined as follows: a: Average sensitivity of bright line (Line A) adjacent to defect line b: Average sensitivity of standard line (Line B) adjacent to Line A Note that the average sensitivity of the bright line is calculated from the region adjacent to the defect region in the defect line. Example: See the right figure Defect region in defect line: From pixel (J, 1) to pixel (J, 15) a: Average sensitivity from pixel (I, 1) to pixel (I, 15) or from pixel (K, 1) to pixel (K, 15) b: Average sensitivity from pixel (H, 1) to pixel (H, 15) or from pixel (L, 1) to pixel (L, 15) /K41/K42/K43 /K44 /K45 /K46/K47 /K48 /K49 /K4A /K43/K6F/K6C/K75/K6D/K6E /K52/K6F/K77 /K4B/K4C/K4D /K4E /K4F /K50 /K51 /K52 /K53 /K31 /K32 /K33 /K34 /K35 /K36 /K37 /K38 /K39 /K31/K30 /K31/K31 /K31/K32 /K31/K33 /K31/K34 /K31/K35 /K31/K36 /K31/K37 /K31/K38 /K31/K39 /K32/K30 /K32/K31 /K32/K32 /K4C/K69/K6E/K65 /K42 /K28/K43/K6F/K6C/K75/K6D/K6E /K48/K2C /K4C/K29 /K44/K65/K66/K65/K63/K74 /K6C/K69/K6E/K65 /K28/K43/K6F/K6C/K75/K6D/K6E /K4A/K29 /K4C/K69/K6E/K65 /K41 /K28/K43/K6F/K6C/K75/K6D/K6E /K49/K2C /K4B/K29 KACCC0385EB Blemish Defect cluster Bright line output adjacent to a defect line KACCC0384EB /K54/K68/K69/K73 /K69/K73 /K64/K65/K66/K69/K6E/K65/K64 /K61/K73 /K64/K65/K66/K65/K63/K74 /K63/K6C/K75/K73/K74/K65/K72/K2E /K4E/K6F/K72/K6D/K61/K6C /K70/K69/K78/K65/K6C /K44/K65/K66/K65/K63/K74/K69/K76/K65 /K70/K69/K78/K65/K6C /K54/K68/K69/K73 /K69/K73 /K6E/K6F/K74 /K64/K65/K66/K69/K6E/K65/K64 /K61/K73 /K64/K65/K66/K65/K63/K74 /K63/K6C/K75/K73/K74/K65/K72/K2E

Cat. No. KACC1167E05 Dec. 2010 DN Flat panel sensor C10900D /K77/K77/K77 /K2E/K68/K61/K6D/K61/K6D/K61/K74/K73/K75/K2E/K63/K6F/K6D /K49/K6E/K66/K6F/K72/K6D/K61/K74/K69/K6F/K6E /K66/K75/K72/K6E/K69/K73/K68/K65/K64 /K62/K79 /K48/K41/K4D/K41/K4D/K41 /K54/K53/K55 /K69/K73 /K62/K65/K6C/K69/K65/K76/K65/K64 /K74/K6F /K62/K65 /K72/K65/K6C/K69/K61/K62/K6C/K65/K2E /K48/K6F/K77/K65/K76/K65/K72 /K2C /K6E/K6F /K72/K65/K73/K70/K6F/K6E/K73/K69/K62/K69/K6C/K69/K74/K79 /K69/K73 /K61/K73/K73/K75/K6D/K65/K64 /K66/K6F/K72 /K70/K6F/K73/K73/K69/K62/K6C/K65 /K69/K6E/K61/K63/K63/K75/K72/K61/K63/K69/K65/K73 /K6F/K72 /K6F/K6D/K69/K73/K73/K69/K6F/K6E/K73/K2E /K53/K70/K65/K63/K69/K66/K69/K63/K61/K74/K69/K6F/K6E/K73 /K61/K72/K65 /K73/K75/K62/K6A/K65/K63/K74 /K74/K6F /K63/K68/K61/K6E/K67/K65 /K77/K69/K74/K68/K6F/K75/K74 /K6E/K6F/K74/K69/K63/K65/K2E /K4E/K6F /K70/K61/K74/K65/K6E/K74 /K72/K69/K67/K68/K74/K73 /K61/K72/K65 /K67/K72/K61/K6E/K74/K65/K64 /K74/K6F /K61/K6E/K79 /K6F/K66 /K74/K68/K65 /K63/K69/K72/K63/K75/K69/K74/K73 /K64/K65/K73/K63/K72/K69/K62/K65/K64 /K68/K65/K72/K65/K69/K6E/K2E /K54 /K79/K70/K65 /K6E/K75/K6D/K62/K65/K72/K73 /K6F/K66 /K70/K72/K6F/K64/K75/K63/K74/K73 /K6C/K69/K73/K74/K65/K64 /K69/K6E /K74/K68/K65 /K73/K70/K65/K63/K69/K66/K69/K63/K61/K74/K69/K6F/K6E /K73/K68/K65/K65/K74/K73 /K6F/K72 /K73/K75/K70/K70/K6C/K69/K65/K64 /K61/K73 /K73/K61/K6D/K70/K6C/K65/K73 /K6D/K61/K79 /K68/K61/K76/K65 /K61 /K73/K75/K66 /K66/K69/K78 /K93/K28/K58/K29/K94 /K77/K68/K69/K63/K68 /K6D/K65/K61/K6E/K73 /K74/K65/K6E/K74/K61/K74/K69/K76/K65 /K73/K70/K65/K63/K69/K66/K69/K63/K61/K74/K69/K6F/K6E/K73 /K6F/K72 /K61 /K73/K75 /K66/K66/K69/K78 /K93/K28/K5A/K29/K94 /K77/K68/K69/K63/K68 /K6D/K65/K61/K6E/K73 /K64/K65/K76/K65/K6C/K6F/K70/K6D/K65/K6E/K74/K61/K6C /K73/K70/K65/K63/K69/K66/K69/K63/K61/K74/K69/K6F/K6E/K73/K2E /KA9/K32/K30/K31/K30 /K48/K61/K6D/K61/K6D/K61/K74/K73/K75 /K50/K68/K6F/K74/K6F/K6E/K69/K63/K73 /K4B/K2E/K4B/K2E /K48/K41/K4D/K41/K4D/K41 /K54/K53/K55 /K50/K48/K4F/K54/K4F/K4E/K49/K43/K53 /K4B/K2E/K4B/K2E /K2C /K53/K6F/K6C/K69/K64 /K53/K74/K61/K74/K65 /K44/K69/K76/K69/K73/K69/K6F/K6E /K31/K31/K32/K36/K2D/K31 /K49/K63/K68/K69/K6E/K6F/K2D/K63/K68/K6F/K2C /K48/K69/K67/K61/K73/K68/K69/K2D/K6B/K75/K2C /K48/K61/K6D/K61/K6D/K61/K74/K73/K75 /K43/K69/K74/K79 /K2C /K34/K33/K35/K2D/K38/K35/K35/K38 /K4A/K61/K70/K61/K6E/K2C /K54 /K65/K6C/K65/K70/K68/K6F/K6E/K65/K3A /K28/K38/K31/K29 /K35/K33/K2D/K34/K33/K34/K2D/K33/K33/K31/K31/K2C /K46 /K61/K78/K3A /K28/K38/K31/K29 /K35/K33/K2D/K34/K33/K34/K2D/K35/K31/K38/K34 /K55/K2E/K53/K2E/K41/K2E/K3A /K48/K61/K6D/K61/K6D/K61/K74/K73/K75 /K43/K6F/K72/K70/K6F/K72/K61/K74/K69/K6F/K6E/K3A /K33/K36/K30 /K46/K6F/K6F/K74/K68/K69/K6C/K6C /K52/K6F/K61/K64/K2C /K50 /K2E/K4F/K2E/K42/K6F/K78 /K36/K39/K31/K30/K2C /K42/K72/K69/K64/K67/K65/K77/K61/K74/K65/K72 /K2C /K4E/K2E/K4A/K2E /K30/K38/K38/K30/K37/K2D/K30/K39/K31/K30/K2C /K55/K2E/K53/K2E/K41/K2E /K2C /K54 /K65/K6C/K65/K70/K68/K6F/K6E/K65/K3A /K28/K31/K29 /K39/K30/K38/K2D/K32/K33/K31/K2D/K30/K39/K36/K30/K2C /K46 /K61/K78/K3A /K28/K31/K29 /K39/K30/K38/K2D /K32/K33/K31/K2D/K31/K32/K31/K38 /K47/K65/K72/K6D/K61/K6E/K79/K3A /K48/K61/K6D/K61/K6D/K61/K74/K73/K75 /K50/K68/K6F/K74/K6F/K6E/K69/K63/K73 /K44/K65/K75/K74/K73/K63/K68/K6C/K61/K6E/K64 /K47/K6D/K62/K48/K3A /K41/K72/K7A/K62/K65/K72/K67/K65/K72/K73/K74/K72 /K2E /K31/K30/K2C /K44/K2D/K38/K32/K32/K31/K31 /K48/K65/K72/K72/K73/K63/K68/K69/K6E/K67 /K61/K6D /K41/K6D/K6D/K65/K72/K73/K65/K65/K2C /K47/K65/K72/K6D/K61/K6E/K79 /K2C /K54 /K65/K6C/K65/K70/K68/K6F/K6E/K65/K3A /K28/K34/K39/K29 /K38/K31/K35/K32/K2D/K33/K37/K35/K2D/K30/K2C /K46 /K61/K78/K3A /K28/K34/K39/K29 /K38/K31/K35/K32/K2D/K32/K36/K35/K2D/K38 /K46/K72/K61/K6E/K63/K65/K3A /K48/K61/K6D/K61/K6D/K61/K74/K73/K75 /K50/K68/K6F/K74/K6F/K6E/K69/K63/K73 /K46/K72/K61/K6E/K63/K65 /K53/K2E/K41/K2E/K52/K2E/K4C/K2E/K3A /K31/K39/K2C /K52/K75/K65 /K64/K75 /K53/K61/K75/K6C/K65 /K54 /K72/K61/K70/K75/K2C /K50/K61/K72/K63 /K64/K75 /K4D/K6F/K75/K6C/K69/K6E /K64/K65 /K4D/K61/K73/K73/K79 /K2C /K39/K31/K38/K38/K32 /K4D/K61/K73/K73/K79 /K43/K65/K64/K65/K78/K2C /K46/K72/K61/K6E/K63/K65/K2C /K54 /K65/K6C/K65/K70/K68/K6F/K6E/K65/K3A /K33/K33/K2D/K28/K31/K29 /K36/K39 /K35/K33 /K37/K31 /K30/K30/K2C /K46 /K61/K78/K3A /K33/K33/K2D/K28/K31/K29 /K36/K39 /K35/K33 /K37/K31 /K31/K30 /K55/K6E/K69/K74/K65/K64 /K4B/K69/K6E/K67/K64/K6F/K6D/K3A /K48/K61/K6D/K61/K6D/K61/K74/K73/K75 /K50/K68/K6F/K74/K6F/K6E/K69/K63/K73 /K55/K4B /K4C/K69/K6D/K69/K74/K65/K64/K3A /K32 /K48/K6F/K77/K61/K72/K64 /K43/K6F/K75/K72/K74/K2C /K31/K30 /K54 /K65/K77/K69/K6E /K52/K6F/K61/K64/K2C /K57 /K65/K6C/K77/K79/K6E /K47/K61/K72/K64/K65/K6E /K43/K69/K74/K79 /K2C /K48/K65/K72/K74/K66/K6F/K72/K64/K73/K68/K69/K72/K65 /K41/K4C/K37 /K31/K42/K57 /K2C /K55/K6E/K69/K74/K65/K64 /K4B/K69/K6E/K67/K64/K6F/K6D/K2C /K54 /K65/K6C/K65/K70/K68/K6F/K6E/K65 /K3A /K28/K34/K34/K29 /K31/K37/K30/K37/K2D/K32/K39/K34/K38/K38/K38/K2C /K46 /K61/K78/K3A /K28/K34/K34/K29 /K31/K37/K30/K37/K2D/K33/K32/K35/K37/K37/K37 /K4E/K6F/K72/K74/K68 /K45/K75/K72/K6F/K70/K65/K3A /K48/K61/K6D/K61/K6D/K61/K74/K73/K75 /K50/K68/K6F/K74/K6F/K6E/K69/K63/K73 /K4E/K6F/K72/K64/K65/K6E /K41/K42/K3A /K53/K6D/K69/K64/K65/K73/K76/KE4/K67/K65/K6E /K31/K32/K2C /K53/K45/K2D/K31/K37/K31 /K34/K31 /K53/K6F/K6C/K6E/K61/K2C /K53/K77/K65/K64/K65/K6E/K2C /K54 /K65/K6C/K65/K70/K68/K6F/K6E/K65/K3A /K28/K34/K36/K29 /K38/K2D/K35/K30/K39/K2D/K30/K33/K31/K2D/K30/K30/K2C /K46 /K61/K78/K3A /K28/K34/K36/K29 /K38/K2D/K35/K30/K39/K2D/K30/K33/K31/K2D/K30/K31 /K49/K74/K61/K6C/K79/K3A /K48/K61/K6D/K61/K6D/K61/K74/K73/K75 /K50/K68/K6F/K74/K6F/K6E/K69/K63/K73 /K49/K74/K61/K6C/K69/K61 /K53/K2E/K52/K2E/K4C/K2E/K3A /K53/K74/K72/K61/K64/K61 /K64/K65/K6C/K6C/K61 /K4D/K6F/K69/K61/K2C /K31 /K69/K6E/K74/K2E /K36/K2C /K32/K30/K30/K32/K30 /K41/K72/K65/K73/K65/K2C /K28/K4D/K69/K6C/K61/K6E/K6F/K29/K2C /K49/K74/K61/K6C/K79 /K2C /K54 /K65/K6C/K65/K70/K68/K6F/K6E/K65/K3A /K28/K33/K39/K29 /K30/K32/K2D/K39/K33/K35/K2D/K38/K31/K2D/K37/K33/K33/K2C /K46 /K61/K78/K3A /K28/K33/K39/K29 /K30/K32/K2D/K39/K33 /K35/K2D/K38/K31/K2D/K37/K34/K31

  • Do not subject the flat panel sensors to strong vibration or shock (Strong shock such as drop impacts may cause permanent damage to these sensors).
  • Users must take responsibility for implementing X-ray shielding safety measures to avoid the risk of X-ray exposure.
  • Data listed in this datasheet was measured at the time of shipment. Characteristics may vary somewhat due to exposure to X-ra ys so take proper countermeasures such as making periodic image correction.
  • This product is warranted for a period of 12 months after the date of the shipment. The warranty is limited to replacement or repair of any defective product due to defects in workmanship or materials used in manufacture. The warranty does not cover loss or damage caused by natural disaster, misuse (including modifications and any use not complying with the environment, application, usage and storage conditions described in this datasheet), or total radiation dose over 25000 Roe ntgen (incident X-ray energy: less than 90 kVp) even within the warranty period.
  • This product is bare board type for installation into equipment and is not covered with a metal shielded case. When designing an equipment, implement EMC measures such as providing electromagnetic shielding on this product and the connection cables. Notice