C10013SK HAMAMATSU | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Features

/K6C Open type tube application /K6C Radiography

Applications

/K6C Low noise: 80 electrons /K6C Energy range: 150 kVp Max. /K6C High quality image: 1 Mpixels /K6C Pixel size: 50 × 50 µm /K6C Digital output (12-bits) /K6C High-speed imaging: 4 frames/s (single binning) /K6C Long life: 150 kVp, 2 MR /K6C Wide dynamic range IMAGE SENSOR Flat panel sensor High reliability, high sensitivity C10013SK I Block diagram C10013SK is a lightweight and compact flat panel sensor consisting of a sensor board and a control board. Each pixel has low noise amplifier. Analog video signals are amplified as the charge on each video line by 1056 ch differential amplifiers with CDS (Correlated Double Sampling) circuits, and are output from each of 8 amplifier arrays. The control board converts the analog video signal into a 12-bit digital signal and outputs it to an external frame grabber through the 12-bit parallel port. DIFFERENTIAL AMP ARRAY No. 1 VERTICAL SHIFT REGISTER TIMING PULSE GENERATOR OSCILLATOR ExtTrgGrb PIXEL NUMBER Vsync Hsync Pclk A/D IntExt EXTERNAL POWER SUPPL Y A.vdd, D.vdd (not attached) DIFFERENTIAL AMP ARRAY No. 8 PHOTODIODE ARRAY BUFFER AMP BUFFER AMP PROCESSING AMP PROCESSING AMP 11151361115135 10561055 211221111057 BIAS GENERATOR ExtTrgLemo FIFO A/D FIFO VIDEO OUTPUT (12 BIT DIGITAL) FOP WITH GOS SCINTILLATOR Note: Signals are readout in order of pixel number. KACCC0207EB

Flat panel sensor C10013SK I General ratings Parameter Specification Unit Pixel size 50 × 50 µm Photodiode area 52.8 × 52.8 mm Number of pixels 1056 × 1056 pixels Number of active pixels 1032 × 1000 pixels Readout Charge amplifier array - Video output (Data1 - 12) LVDS (differential) 12 bit - Output data rate 12.5 MHz Synchronous signal (Vsync, Hsync, Pclk) LVDS (differential) - ExtTrgGrb, ExtTrgLemo, IntExt TTL - Scintillator CsI - I Absolute maximum ratings (Ta=25 °C) Parameter Symbol Value Unit Supply voltage for digital circuitry (+5 V) D.vdd +6.0 V Supply voltage for analog circuitry (+5 V) A.vdd +6.0 V Input voltage (ExtTrgGrb, ExtTrgLemo, IntExt) Vin 0 to 6.0 V Operating temperature *1 Topr 0 to +35 °C Storage temperature *1 Tstg 0 to +50 °C *1: No condensation I Specification (Ta=25 °C, A.vdd= 5.0 V, D.vdd= 5.0 V) Parameter Symbol Min. Typ. Max. Unit Frame rate (single operation) Sf (int) 3.8 4 - frames/s Frame rate external (single operation ) Sf (ext) - Sf (int) to 1 - frames/s Noise (rms) *2 N (rms) - 80 - electrons Sensitivity *3 S 120 150 - LSB/mR Saturation charge Csat - 0.3 - M electrons Resolution *4 Reso 7.1 8 - line pairs/mm Dynamic range - - 3800 - - Defect line *5 - - - 15 lines Adjacent defect line - - - 1 lines Output offset *6 - - 65 200 LSB *2: Internal trigger mode, single operation *3: At 150 kVp without filter *4: Spatial frequency at CTF=5 % *5: A defect line is a horizontal or vertical line containing 4 or more pixels that produce less than 1/8 of the average output from surrounding pixels and are formed continuously from the opposite side of an amplifier array or a vertical shift register. *6: Average of all effective pixels in single operation at Sf (int) Note: X-ray energy range is 20 k to 150 kVp. I Resolution SPATIAL FREQUENCY (line pairs/mm) CTF (%) 100 02468 13579 1 0 (Ta=25 ˚C, A.vdd=5.0 V, D.vdd=5.0 V) KACCB0174EA

Flat panel sensor C10013SK I Timing chart T o acquire images through an image grabber board, write parameters in the software program or parameter file by referring to the following timing chart and description. KACCC0362EA

1 FRAME

All pulses are counted in the “High” period of Hsync+ All pulses are counted at the rising edge of Pclk+. The effective video output is only included in the “Phe” period. LAST ROW Vsync+ (GRABBER) Vsync+ (GRABBER) Hsync+ (GRABBER) Hsync+ (GRABBER) Pclk+ (GRABBER) Parameter Count Effective line 1000He Dummy line 56 Effective pixel 1032Phe Dummy pixel 24 Phd 1870 Pg 1877 Note: “He” is the Hsync count. Phe, Phd and Pg are the Pclk count. KACCC0372EA RECOMMENDATION: 50 % OF FRAME TIME From Tmin to Tmax Tvd ExtTrgLemo ExtTrgGrb (TTL) Vsync+ (LVDS) Hsync+, Pclk+ and Data 1-12 are the same as internal trigger mode.

  • Tmin is defined as 1/Sf (int).
  • Tmax is defined as the reciprocal of the minimum value of Sf (ext).
  • Tvd=320 µs I External trigger mode T o acquire images in external trigger mode, input an external trigger pulse as shown below. When the time Tvd has passed after the rising edge of the external trigger pulse, synchronous signals and video signals are output.

Flat panel sensor C10013SK I System requirements T o operate C10013SK at full performance, the following system and peripherals are required.

  • PC: IBM compatible PC running on Windows XP
  • Digital frame grabber card: Monochrome 16 bits or more, pixel clock 13 MHz or more, LVDS interface synchronous signal (See the frame grabber manual.) The National Instruments IMAQ PCI-1424 (NI parts No. 777662-02) frame grabber has been verified to successfully acquire 12- bit digital images from C10013SK. The IMAQ PCI-1422 (NI pats No. 777959-02) also acquires satisfactory images from C10013SK. Y ou can utilize the demonstration software that comes with the frame grabber as a simple viewer, to acquire and save an image. T o do so, refer to the frame grabber user’s guide for how to use the camera information file for the demonstration software. Please use of a series power supply. (Avoid using a switching power supply.) A power cable (terminated with an FGG.2B.307.CLAD92Z plug at one end and open at the other end; 2 m; see T able 2.), an external trigger cable (terminated with an FFA.0S.302.CLAC37 plug at one end and open at the other end; 5 m; see table 3.) and an earth cable (AWG 18; 4 m) comes supplied with C10013SK. An optional frame grabber cable for interface with the 40-pin receptacle (see T able 1) on C10013SK is also available for synchronous signal, video output and external control. The voltages described above are specified at the flat panel sensor side. The impedance of the power cable attached with the flat panel sensor is low enough but it causes 0.1 V approx. drop. Therefore the voltage at the power source side should be set 0.1 V higher than the voltage specified above. Install a noise filter on the AC power input line to prevent surges on the AC line. T o supply the synchronous signal through ExtT rgGrb, apply high level of TTL to ExtT rgLemo and IntExt, or leave them without connection. On the contrary, to use ExtT rgLemo, set high level to ExtT rgGrb and IntExt, or leave them without connection. The earth terminal must be connected to a stable earth point to eliminate noise from surroundings. Table 1: Pin assignment of 40-pin receptacle Pin No. Signal Pin No. Signal

1 Data1+ (LSB) 21 Data1- (LSB)

2 Data2+ 22 Data2-

3 Data3+ 23 Data3-

4 Data4+ 24 Data4-

5 Data5+ 25 Data5-

6 Data6+ 26 Data6-

7 Data7+ 27 Data7-

8 Data8+ 28 Data8-

9 Data9+ 29 Data9-

10 Data10+ 30 Data10-

11 Data11+ 31 Data11-

12 Data12+ (MSB) 32 Data12- (MSB)

13 Reserved 33 Reserved

14 Reserved 34 Reserved

15 Reserved 35 GND

16 Reserved 36 GND

17 ExtTrgGrb (TTL) 37 IntExt (TTL)

18 Vsync+ 38 Vsync-

19 Hsync+ 39 Hsync-

20 Pclk+ 40 Pclk-

Unless otherwise noted, signal level is LVDS. 40-pin receptacle: 10240-52B2PL made by 3M Co. Ltd. Mating plug: 10140-6000EL made by 3M Co. Ltd. Table 2: Power pin assignment and cable color Pin No. Color Signal

1 Brown Reserved

2 Red Reserved

3 Orange Reserved

4 Yellow Analog GND

5 Green Analog +5 V

6 Blue Digital GND

7 Purple Digital +5 V

Table 3: External trigger pin assignment and cable color Pin No. Color Signal

1 Red ExtTrgLemo (TTL)

2 Black Signal GND

Flat panel sensor C10013SK I Connection Install the frame grabber board into the PC by the manufacturer’s instructions. When a general-purpose frame grabber board is used, binning or trigger operation for IntExt and ExtT rgGrb can be controlled with its digital I/O control. KACCC0291EB VIDEO OUTPUT (12 BIT DIGITAL) Vsync, Hsync, Pclk IntExt ExtTrgGrb X-RAY SOURCE FRAME GRABBER MONITOR PC/AT (REAR VIEW) ExtTrgLemo OS + ACQUISITION SOFTWAREVOLTAGE SOURCE (A.vdd, D.vdd) C10013SK CMOS FLAT PANEL SENSOR C10013SK I Dimensional outline (unit: mm, tolerance: ±1 mm unless otherwise noted) KACCA0173EC 152 38 145 50 9 ACTIVE AREA Top cover is made of carbon fiber (1.0 mm thickness). Weight: 2.7 kg * ±0.5 mm 52.6 ACTIVE AREA 51.6 SCINTILLATOR TO TOP COVER 11.3 16.4 15 *120 * 15 *120 *17.4 18.5 16.4 10 *118 * 5023.516.5EXT.TRG. POWER DIGITAL OUT CMOS FLAT PANEL SENSOR C10013SK CMOS FLAT PANEL SENSOR C10013SK (4 ×) M3 DEPTH 4 mm

Flat panel sensor C10013SK I Notice

  • Do not subject the Flat Panel Sensors to strong vibration or shock. (Strong shock such as drop impacts may cause permanent damage to these sensors.)
  • Users must take responsibility for implementing X-ray shielding safety measures to avoid the risk of X-ray exposure.
  • Data listed in this datasheet is defined at the time of shipment. Characteristics may vary somewhat due to exposure to X-rays so take proper coutermeasures such as making periodic image correction.
  • This product is warranted for a period of 12 months after the date of the shipment. The warranty is limited to replacement or repair of any defective product due to defects in workmanship or materials used in manufacture. The warranty does not cover loss or damage caused by natural disaster, misuse (including modifications and any use not complying with the environment, application, usage and storage conditions described in this datasheet), or total radiation dose over 2 million Roentgen (less than 150 kVp) even within the warranty period.
  • As described above, flat panel sensors have limited resistance to radiation. This must be taken into account when using a flat panel sensor under continuous irradiation (in-line non-destructive inspection, etc.) When using flat panel sensors in non-destructive inspection equipment, please contact us and provide information such as irradiation conditions. I Optional frame grabber cables Frame grabber Cable type No. Cable length Cable end Cable end A8406-51 5 m A8406-56 7 m A8406-57 10 mGeneral-purpose A8406-58 12 m open A8406-52 5 m A8406-53 7 m A8406-54 10 mIMAQ PCI-1424 *7 A8406-55 12 m 10140-6000EL *8 PCS-XE100MA+ *9 *7: Made by NI (National Instrument Corporation) *8: Made by 3M Co. Ltd. *9: Made by Honda Tsushin Kogyo Co. Ltd. Note: The detailed information for these optional cables is shown in the datasheet of A8406 series. HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184, www.hamamatsu.com Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741 Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2007 Hamamatsu Photonics K.K. Cat. No. KACC1122E06 May 2007 DN C10013SK conforms to European EMC directives: EN61326 Class A.