ASL331_17 ASB | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 11
Technical content
1/11 ASB Inc. sales@asb.co.kr Tel: +82-42-528-7225 September 2017 ASL331 Wideband Linear Push-pull Amplifier MMIC 1) OIP3 and OIP2 are measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2) OIP3 is measured with two tones at an output power of +12 dBm/tone separated by 6 MHz. 3) OIP2 is measured at F1+F2 Frequency. 4) OIP2 is measured with two tones at an output power of +14 dBm/tone at F1(400 MHz)+F2(450 MHz). 5) Pout = 101 dBuV for 84 channels VHF signal. Parameters Units Min Typ. Max Testing Frequency MHz 500 Gain dB 19.2 S11 dB -16 S22 dB -16 Output IP3 dBm 42.0 Noise Figure dB 1.8 Output P1dB dBm 26 Current mA 220 Device Voltage V +5 Parameters Rating Operating Case Temperature -40 to 85 C Storage Temperature -40 to 150 C Device Voltage +6 V Operating Junction Temperature +150 C Input RF Power (CW, 75 matched) +18 dBm Maximum Current 300 mA Thermal Resistance 18 C/W Parameters Units Typical Frequency MHz 5 50 500 860 1002 1200 S11 dB -20 -18 -16 -17 -15 -13 S22 dB -20 -18 -16 -17 -15 -13 Output P1dB dBm 25 26 26 25 25 25 Output IP2 dBm 601), 3) 614) CSO5) dBc 64 CTB5) dBc 60 Current mA 220 Device Voltage V +5 Features Description Typical Performance (Supply Voltage = +5 V, TA = +25 C, Z0 = 75 ) Absolute Maximum Ratings High Linearity 41 dBm OIP3 Low Noise Figure 1.6 dB 26 dBm P1dB 75 Input & Output Match Bandwidth 5 ~ 1200 MHz Single Supply +5 V The ASL331, a wideband linear push -pull amplifi- er MMIC, has a high linearity and low noise over a wide range of frequency 5 MHz to 1 .2 GHz, being suitable for use in the fiber receiver, distribution amplifiers and drop amplifiers of CATV systems, and in the m obile wireless repeaters and BTS. The amplifier is available in a SOIC8 package and passes through the stringent DC, RF, and reliabil- ity tests. Application Circuit
- 50 ~ 1000 MHz (1:1 transformer)
- 5 ~ 200 MHz (1:1 transformer) Product Specifications ASL331 Pin Configuration Pin No. Function
1 RF IN 1
2,3,6,7 NC
4 RF IN 2
5 RF OUT 2
8 RF OUT 1
50 ~ 1002 MHz 50 ~ 1200 MHz 50 ~ 860Hz 5 ~ 300 MHz (Without LPF) 5 ~ 300 MHz (LPF) 200 ~ 600 MHz (50 ) 5 ~ 200 MHz (Trans-impedance Amplifier, 75 )
2/11 ASB Inc. sales@asb.co.kr Tel: +82-42-528-7225 September 2017 ASL331 Wideband Linear Push-pull Amplifier MMIC Pin No. Function Pin No. Function.
1 RF IN 1 5 RF OUT 2
2 NC 6 NC
3 NC 7 NC
4 RF IN 2 8 RF OUT 1
Mounting Recommendation (In mm) Outline Drawing Note: 1. Backside metal paddle is RF and DC ground. Symbols Dimensions (In mm) MIN NOM MAX A 1.40 1.50 1.60 A1 0.00 --- 0.10 A2 --- 1.45 --- B 0.33 --- 0.51 C 0.19 --- 0.25 D 4.80 --- 5.00 D2 3.20 3.30 3.40 E 5.80 6.00 6.20 E1 3.80 3.90 4.00 E2 2.30 2.40 2.50 e --- 1.27 --- L 0.40 --- 1.27 y --- --- 0.10 0 --- 8 L1 1.04REF
- ASL331 Part No. ESD Classification HBM Class 1B Voltage Level: 550 V MM Class A Voltage Level: 50 V CAUTION: ESD-sensitive device! Moisture Sensitivity Level (MSL) Level 3 at 260 C reflow Note: 1. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 2. To ensure reliable operation, device ground paddle-to-ground pad soldering is critical. 3. Add mounting screws near the part to fasten the board to a heat sinker. Ensure that the ground / thermal via region con- tacts the heat sinker. 4. A proper heat dissipation path underneath the are a of the PCB for the mounted device is strictly required for proper thermal operation. Damage to the device can result from in- appropriate heat dissipation.
3/11 ASB Inc. sales@asb.co.kr Tel: +82-42-528-7225 September 2017 ASL331 Wideband Linear Push-pull Amplifier MMIC 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 Gain (dB) Frequency (MHz) -40 o c o c o c 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 -30 -25 -20 -15 -10 S11 (dB) Frequency (MHz) -40 o c o c o c 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 -30 -25 -20 -15 -10 S22 (dB) Frequency (MHz) -40 o c o c o c 1) OIP3 is measured with two tones at an output power of +12 dBm/tone separated by 6 MHz. 2) OIP2 is measured with two tones at an output power of +14 dBm/tone at F1(400 MHz)+F2(450 MHz). 3) Pout = 101 dBuV for 84 channels VHF signal. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic APPLICATION CIRCUIT Frequency (MHz) 50 500 1002 Noise Figure (dB) 1.8 1.8 1.9 Magnitude S21 (dB) 19.5 19.2 19.0 Magnitude S11 (dB) -18 -16 -15 Magnitude S22 (dB) -18 -16 -15 Output P1dB (dBm) 25 26 25 Output IP31) (dBm) 38 42 36 Output IP22) (dBm) 61 CSO (dBc)3) 64 CTB (dBc) 3) 60 Device Voltage (V) +5 Current (mA) 220 Note: MABA-007159 1:1 impedance transformers are used. S-parameters CATV Push-Pull 1 : 1 transformer 50 ~ 1002 MHz +5 V
4/11 ASB Inc. sales@asb.co.kr Tel: +82-42-528-7225 September 2017 ASL331 Wideband Linear Push-pull Amplifier MMIC -60 -40 -20 0 20 40 60 80 100 P1dB (dBm) Temperature ( o @ 500 MHz -60 -40 -20 0 20 40 60 80 100 Gain (dB) Temperature ( o Frequency = 500 MHz 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 @ 500 MHz Output IP3 (dBm) Pout per Tone (dBm) -40 o c o c o c 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 100 @ 400 MHz + 450 MHz Output IP2 (dBm) Pout per Tone (dBm) -40 o c o c o c -60 -40 -20 0 20 40 60 80 100 100 150 200 250 300 350 400 Current (mA) Temperature ( o P1dB vs. Temperature Current vs. Temperature Output IP2 vs. Tone Power Gain vs. Temperature Output IP3 vs. Tone Power
5/11 ASB Inc. sales@asb.co.kr Tel: +82-42-528-7225 September 2017 ASL331 Wideband Linear Push-pull Amplifier MMIC 0 200 400 600 800 1000 1200 1400 -25 -20 -15 -10 S22 (dB) Frequency (MHz) 0 200 400 600 800 1000 1200 1400 -30 -25 -20 -15 -10 S11 (dB) Frequency (MHz) 0 200 400 600 800 1000 1200 1400 Gain (dB) Frequency (MHz) 1) OIP3 is measured with two tones at an output power of +12 dBm/tone separated by 6 MHz. 2) OIP2 is measured with two tones at an output power of +14 dBm/tone at F1(400 MHz)+F2(450 MHz). Board Layout (FR4, 40x40 mm2, 0.8T) Schematic APPLICATION CIRCUIT Frequency (MHz) 50 500 1200 Noise Figure (dB) 1.8 1.8 2.1 Magnitude S21 (dB) 19.0 19.0 19.0 Magnitude S11 (dB) -17 -15 -13 Magnitude S22 (dB) -17 -15 -13 Output P1dB (dBm) 25 26 25 Output IP31) (dBm) 39.0 42.5 38.5 Output IP22) (dBm) 59 Device Voltage (V) +5 Current (mA) 220 Note: MABA-007159 1:1 impedance transformers are used. S-parameters CATV Push-Pull 1 : 1 transformer 50 ~ 1200 MHz +5 V
6/11 ASB Inc. sales@asb.co.kr Tel: +82-42-528-7225 September 2017 ASL331 Wideband Linear Push-pull Amplifier MMIC 0 200 400 600 800 1000 -30 -25 -20 -15 -10 S22 (dB) Frequency (MHz) 0 200 400 600 800 1000 -30 -25 -20 -15 -10 S11 (dB) Frequency (MHz) 0 200 400 600 800 1000 Gain (dB) Frequency (MHz) 1) OIP3 is measured with two to nes at an output power of +12 dBm/tone separated by 6 MHz. 2) OIP2 is measured with two tones at an output power of +14 dBm/tone at F1(400 MHz)+F2(450 MHz). Board Layout (FR4, 40x40 mm2, 0.8T) Schematic APPLICATION CIRCUIT Frequency (MHz) 50 500 860 Noise Figure (dB) 1.8 1.8 1.9 Magnitude S21 (dB) 19.5 19.2 19.0 Magnitude S11 (dB) -18 -17 -17 Magnitude S22 (dB) -18 -17 -17 Output P1dB (dBm) 25 26 25 Output IP31) (dBm) 37.5 41.5 37.5 Output IP22) (dBm) 60 Device Voltage (V) +5 Current (mA) 220 Note: MABA-CT0040 1:1 impedance transformers are used. S-parameters CATV Push-Pull 1 : 1 transformer 50 ~ 860 MHz +5 V
7/11 ASB Inc. sales@asb.co.kr Tel: +82-42-528-7225 September 2017 ASL331 Wideband Linear Push-pull Amplifier MMIC 1) OIP3 and OIP2 are measure d with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2) OIP2 is measured at F1+F2 Frequency. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic APPLICATION CIRCUIT Frequency (MHz) 5 50 200 Noise Figure (dB) 1.6 1.4 1.5 Magnitude S21 (dB) 20.9 20.9 20.7 Magnitude S11 (dB) -20 -20 -18 Magnitude S22 (dB) -20 -20 -18 Output P1dB (dBm) 25.0 25.0 25.5 Output IP31) (dBm) 37.5 38.5 40.5 Output IP21),2) (dBm) 60 70 71 Device Voltage (V) +5 Current (mA) 220 Note: MABA-007159 1:1 impedance transformers are used. S-parameters CATV Push-Pull 1 : 1 transformer 5 ~ 300 MHz & Without LPF +5 V 0 200 400 600 800 1000 1200 1400 1600 1800 2000 -50 -40 -30 -20 -10 Gain (dB) Frequency (MHz) 0 200 400 600 800 1000 1200 1400 1600 1800 2000 -50 -40 -30 -20 -10 S11 (dB) Frequency (MHz) 0 200 400 600 800 1000 1200 1400 1600 1800 2000 -50 -40 -30 -20 -10 S22 (dB) Frequency (MHz)
8/11 ASB Inc. sales@asb.co.kr Tel: +82-42-528-7225 September 2017 ASL331 Wideband Linear Push-pull Amplifier MMIC 1) OIP3 and OIP2 are measured with two tones at an output power of +10 dBm /tone separated by 1 MHz. 2) OIP2 is measured at F1+F2 Frequency. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic APPLICATION CIRCUIT Frequency (MHz) 5 50 200 Noise Figure (dB) 2.0 1.4 1.4 Magnitude S21 (dB) 21.0 20.9 20.6 Magnitude S11 (dB) -22 -22 -22 Magnitude S22 (dB) -22 -22 -22 Output P1dB (dBm) 24.5 25.0 24.5 Output IP31) (dBm) 37.0 38.5 43.0 Output IP21),2) (dBm) 60 70 60 Device Voltage (V) +5 Current (mA) 220 Note: MABA-007159 1:1 impedance transformers are used. S-parameters CATV Push-Pull 1 : 1 transformer 5 ~ 300 MHz & LPF +5 V 0 200 400 600 800 1000 1200 1400 1600 1800 2000 -50 -40 -30 -20 -10 Gain (dB) Frequency (MHz) 0 200 400 600 800 1000 1200 1400 1600 1800 2000 -50 -40 -30 -20 -10 S11 (dB) Frequency (MHz) 0 200 400 600 800 1000 1200 1400 1600 1800 2000 -50 -40 -30 -20 -10 S22 (dB) Frequency (MHz)
9/11 ASB Inc. sales@asb.co.kr Tel: +82-42-528-7225 September 2017 ASL331 Wideband Linear Push-pull Amplifier MMIC 1) OIP3 is measured with two tones at an output power of +1 0 dBm/tone separated by 1 MHz. C1=1 F 1 : 1 Transformer Transformer 1 : 1ASL331 Vs = 5V Vs = 5V RF IN RF OUT (LQH31CN1R0M03) (LQH31CN1R0M03) R2=560 R1=560 C8=10 F C7=1 F C6=1 FC5=1 F C4=10 F C3=1 F C2=1 F L2=1 H L1=1 H 0 100 200 300 400 500 600 700 800 900 1000 -30 -25 -20 -15 -10 S22 (dB) Frequency (MHz) 0 100 200 300 400 500 600 700 800 900 1000 -30 -25 -20 -15 -10 S11 (dB) Frequency (MHz) 0 100 200 300 400 500 600 700 800 900 1000 Gain (dB) Frequency (MHz) Board Layout (FR4, 40x40 mm2, 0.8T) Schematic APPLICATION CIRCUIT Frequency (MHz) 5 200 600 Noise Figure (dB) 1.5 1.6 1.7 Magnitude S21 (dB) 20.0 20.2 20.0 Magnitude S11 (dB) -10 -17 -17 Magnitude S22 (dB) -10 -15 -15 Output P1dB (dBm) 25.5 26.0 26.0 Output IP31) (dBm) 40 41 42 Device Voltage (V) +5 Current (mA) 220 Note: MABA-007159 1:1 impedance transformers are used. S-parameters IF (50 200 ~ 600 MHz +5 V 0 500 1000 1500 2000 2500 3000 3500 Stability Factor Frequency (MHz)
10/11 ASB Inc. sales@asb.co.kr Tel: +82-42-528-7225 September 2017 ASL331 Wideband Linear Push-pull Amplifier MMIC 1) OIP3 is measured with two tones at an output power of -6 dBm/tone separated by 1 MHz. 2) OIP2 is measured at F1+F2 Frequency. ASL331 R4=1 kΩ R3=1 kΩ C4=1 μF C5=1 μF C7=3.0 pF C2=1 μF C3=1 μF L3=6.8 nH L4=6.8 nH L1=BLM15HD182SN L2=BLM15HD182SN R1=1 kΩ R2=1 kΩ Vdiode = +12 V C9=39 pF C10=39 pF R6=13 Ω R6=13 Ω Vs = +5 V Vs = +5 V C6=10 μF C8=10 μF C11=1 μF C12=1 μF 1 : 1 Transformer RF OUT L5=4.7 μH L6=4.7 μH (LQH31CN4R7M03) (LQH31CN4R7M03) Board Layout (FR4, 40x40 mm2, 0.8T) Schematic APPLICATION CIRCUIT Frequency (MHz) 5 200 Magnitude S21 (dB) 23 24 Magnitude S22 (dB) -9.5 -9.5 EIN (pA/√Hz) 5.0 4.0 Output IP31) (dBm) 25 23 Output IP21),2) (dBm) 43 45 Device Voltage (V) +5 Current (mA) 220 Note: MABA-007159 1:1 impedance transformers are used. S-parameters Trans-impedance Amplifier (75 5 ~ 200 MHz +5 V
11/11 ASB Inc. sales@asb.co.kr Tel: +82-42-528-7225 September 2017 ASL331 Wideband Linear Push-pull Amplifier MMIC 260 C 150 C 60~180 sec Ramp-up (3 C/sec) Ramp-down (6 C/sec) Copyright 2011-2017 ASB Inc. All rights reserved. Da tasheet subject to change without notice. ASB assumes no re- sponsibility for any errors which may appear in this datasheet. No part of the datasheet may be copied or reproduced in any form or by any means without the prior written consent of ASB. Recommended Soldering Reflow Profile 20~40 sec 200 C