AS8ER128K32_03 AUSTIN | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 17

Technical content

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life PLEASE NOTE: An EOL notice was issued on this product in 2001. However, ASI has a large amount of die inventory available. For assistance, please contact your local sales representative.

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life GENERAL DESCRIPTION The Austin Semiconductor, Inc. AS8ER128K32 is a 4 Megabit Radiation Tolerant EEPROM Module organized as 128K x 32 bit. User configurable to 256K x16 or 512Kx 8. The module achieves high speed access, low power consumption and high reliability by employing advanced CMOS memory technology. The military grade product is manufactured in compliance to MIL-STD 883, making the AS8ER128K32 ideally suited for military or space applications. The module is offered as a 68 lead 0.990 inch square ceramic quad flat pack. It has a max. height of 0.200 inch. This package design is targeted for those applications which require low profile SMT Packaging. * contact factory for test reports. ASI does not guarantee or warrant these performance levels, but references these third party reports.

FEATURES

  • Access time of 150ns
  • Operation with single 5V + 10% supply
  • Power Dissipation: Active: 1.43 W (MAX), Max Speed Operation Standby: 7.7 mW (MAX), Battery Back-up Mode
  • On-Chip Latches: Address, Data, CE\\, OE\\, WE\\
  • Automatic Byte Write: 10 ms (MAX)
  • Automatic Page Write (128 bytes): 10 ms (MAX)
  • Data protection circuit on power on/off
  • Low power CMOS
  • 1 0

4 Erase/Write cycles (in Page Mode)

  • Software data protection
  • TTL Compatible Inputs and Outputs
  • Data Retention: 10 years
  • Ready/Busy\\ and Data Polling Signals
  • Write protection by RES\\ pin
  • Radiation Tolerant: Proven total dose 40K to 100K RADS*
  • Operating Temperature Ranges: Military: -55 oC to +125oC Industrial: -40oC to +85oC OPTIONS MARKINGS
  • Timing 150 ns -150 200 ns -200 250 ns -250
  • Package Ceramic Quad Flat pack Q No. 703 Ceramic Quad Flat pack QB AVAILABLE AS MILITARY SPECIFICATIONS
  • MIL-STD-883
  • SMD 5962-94585 PIN ASSIGNMENT (Top View)

68 Lead CQFP

For more products and information please visit our web site at www.austinsemiconductor.com I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 GND I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 9 8 7 6 5 4 3 2 1 68 67 66 65 64 63 62 61 RES\\ CS3\\ GND CS4\\ WE1\\ A10 Vcc 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Vcc A11 A12 A13 *A15 *A14 A16 CS1\\ OE\\ CS2\\ NC WE2\\ WE3\\ WE4\\ NC NC RDY I/O16 I/O17 I/O18 I/O19 I/O20 I/O21 I/O22 I/O23 GND I/O24 I/O25 I/O26 I/O27 I/O28 I/O29 I/O30 I/O31 PIN NAME FUNCTION A0 to A16 Address Input I/O0 to I/O31 Data Input/Output OE\\ Output Enable CE\\ Chip Enable WE\\ Write Enable V CC Power Supply VSS Ground RDY/BUSY\\ Ready Busy RES\\ Reset FUNCTIONAL BLOCK DIAGRAM *Pin #'s 31 and 32, A15 and A14 respectively, are reversed from the AS8E128K32. Correct use of these address lines is required for operation of the SDP mode to work properly.

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of LifeNOTES: 1. RDY/Busy\\ output has only active LOW VOL and high impedance state. It can not go to HIGH (VOH) state. 2. VCC -0.5 < VH < VCC +1.0 3. X : DON'T CARE TRUTH TABLE MODE CE\\ OE\\ WE\\ RES\\ RDY/BUSY\\1 I/O Read VIL VIL VIH VH

2 High-Z Dout

Standby VIH X3 X X High-Z High-Z Write VIL VIH VIL VH High-Z to VOL Din Deselect VIL VIH VIH VH High-Z High-Z XX VIH X --- --- X VIL X X --- --- Data\\ Polling VIL VIL VIH VH VOL Dout (I/O7) Program Reset X X X VIL High-Z High-Z Wirte Inhibit

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life *Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. **Junction temperature depends upon package type, cycle time, loading, ambient temperature and airflow, and humidity (plastics). ABSOLUTE MAXIMUM RATINGS* V oltage on Vcc Supply Relative to Vss Operating Temperature Range Thermal Resistance junction to case ( θJC): NOTES: 1) Including electrical characteristics and data retention. 2) VIN MIN = -3.0V for pulse width < 20ns. ELECTRICAL CHARACTERISTICS AND RECOMMENDED DC OPERATING CONDITIONS (-55oC<TA<125oC or -40oC to +85oC; Vcc = 5V + 10%) MAX CONDITIONS SYM -15 UNITS Iout = 0mA, VCC = 5.5V Cycle = 1µS, Duty = 100% Iout = 0mA, VCC = 5.5V Cycle = MIN, Duty = 100% 260 CE\\ = VCC, VCC = 5.5V I CC1 1.4 mA CE\\ = VIH, VCC = 5.5V I CC2 12 mA Power Supply Current: Standby Icc3 mA PARAMETER Power Supply Current: Operating PARAMETER CONDITIONS SYMBOL MIN MAX UNITS Input High Voltage VIH 2.2 VCC +0.3 V Input High Voltage (RES\\) VH VCC -0.5 V CC +1.0 V Input Low Voltage VIL -0.31 0.8 V INPUT LEAKAGE CURRENT OV < VIN < VCC ILI -10 10 µΑ OUTPUT LEAKAGE CURRENT Outputs(s) Disabled, OV < VOUT < VCC ILO -10 10 µΑ Output High Voltage IOH = -0.4mA V OH 2.4 -- V Output Low Voltage IOL = 2.1mA V OL -- 0.4 V Supply Voltage VCC 4.5 5.5 V NOTE: 1) VIL (MIN): -1.0V for pulse width < 20ns. 2) ILI on RES\\ : 500µA (MAX)

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life NOTE: 1. This parameter is guaranteed but not tested. CAPACITANCE TABLE1 (VIN = 0V, f = 1 MHz, TA = 25oC) SYMBOL PARAMETER MAX UNITS CADD A0 - A16 Capacitance 40 pF COE OE\\, RES\\, RDY Capacitance 40 pF CWE, CCE WE\\ and CE\\ Capacitance 12 pF CIO I/O 0- I/O 31 Capacitance 20 pF ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CONDITIONS (-55oC < TA < +125oC or -40oC to +85oC; Vcc = 5V +10%) MIN MAX Address to Output Delay CE\\ = OE\\ = VIL, WE\\ = VIH tACC 150 ns CE\\ to Output Delay OE\\ = VIL, WE\\ = VIH tCE 150 ns OE\\ to Output Delay OE\\ = V IL, WE\\ = VIH tOE 10 75 ns Address to Output Hold CE\\ = OE\\ = VIL, WE\\ = VIH tOH 0n s CE\\ or OE\\ high to Output Float (1) OE\\ = VIL, WE\\ = VIH tDF 05 0n s RES\\ low to Output Float (1) CE\\ = OE\\ = V IL, WE\\ = VIH tDFR 0 350 ns RES\\ to Output Delay CE\\ = OE\\ = V IL, WE\\ = VIH tRR 0 450 ns DESCRIPTION 150 SYMBOL UNITSTEST CONDITIONS AC TEST CHARACTERISTICS TEST SPECIFICATIONS OH OLI ICurrent Source Current Source Vz = 1.5V (Bipolar Supply) Device Under Test Ceff = 50pf NOTES: Vz is programmable from -2V to + 7V . I OL and IOH programmable from 0 to 16 mA. Vz is typically the midpoint of VOH and VOL. IOL and IOH are adjusted to simulate a typical resistive load circuit. Figure 1

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC WRITE CHARACTERISTICS (-55oC < TA < +125oC; Vcc = 5V +10%) SYMBOL PARAMETER MIN (2) MAX UNITS tAS Address Setup Time 0 ms tAH Address Hold Time 150 ns tCS CE\\ to Write Setup Time (WE\\ controlled) 0 ns tCH CE\\ Hold Time (WE\\ controlled) 0 ns tWS WE\\ to Write Setup Time (CE\\ controlled) 0 ns tWH WE\\ to Hold Time (CE\\ controlled) 0 ns tOES OE\\ to Write Setup Time 0 ns tOEH OE\\ to Hold Time 0 ns tDS Data Setup Time 100 ns tDH Data Hold Time 10 ns tWP WE\\ Pulse Width (WE\\ controlled) 250 ns tCW CE\\ Pulse Width (CE\\ controlled) 250 ns tDL Data Latch Time 300 ns tBLC Byte Load Cycle 0.55 30 µs tBL Byte Load Window 100 µs tWC Write Cycle Time 10 (3) ms tDB Time to Device Busy 120 ns tDW Write Start Time 150 (4) ns tRP Reset Protect Time 100 µs tRES Reset High Time (5) 1µ s READ TIMING WAVEFORM tACC tCE tOE tOH tDF tDFR tRR HIGH-Z ADDRESS CE\\ OE\\ WE\\ Data Out RES\\ DATA OUT V ALID VIH

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life BYTE WRITE TIMING WAVEFORM (WE\\ CONTROLLED) BYTE WRITE TIMING WAVEFORM (CE\\ CONTROLLED) tRES tRP HIGH-Z tOES tAS tCS tAH tWC tCH tBL tOEH tWP tDS tDH tDB tDW HIGH-Z VCC RES\\ RDY/Busy\\ Din OE\\ WE\\ CE\\ Address VOL tRES tRP HIGH-Z tOES tAS tWS tAH tWC tWH tBL tOEH tCW tDS tDH tDB tDW HIGH-Z VCC RES\\ RDY/Busy\\ Din OE\\ WE\\ CE\\ Address VOL

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life PAGE WRITE TIMING WAVEFORM (WE\\ CONTROLLED) PAGE WRITE TIMING WAVEFORM (CE\\ CONTROLLED) HIGH-Z HIGH-Z VCC RES\\ RDY/Busy\\ Din OE\\ CE\\ WE\\ Address(6) A0 to A16 tRES tRP tDB tDS tDH tOES tCS tCH tBLC tDL tWP tAS tAH tBL tWC tOEH tDW HIGH-Z HIGH-Z VCC RES\\ RDY/Busy\\ Din OE\\ WE\\ CE\\ Address(6) A0 to A16 tRES tRP tDB tDS tDH tOES tWS tWH tBLC tDL tCW tAS tAH tBL tWC tOEH tDW

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life DATA POLLING TIMING WAVEFORM AnAn Din X Dout X Dout X tOE (7) tWC tOEH tCE (7) tOES tDW Address CE\\ WE\\ OE\\ I\\O7 NOTES: 1. tDF and tDFR are defined as the time at which the outputs achieve the open circuit conditions and are no longer driven. 2. Use this device in longer cycle than this value. 3. t WC must be longer than this value unless polling techniques or RDY/Busy\\ are used. This device automatically com- pletes the internal write operation within this value. 4. Next read or write operation can be initiated after t DW if polling techniques or RDY/Busy\\ are used. 5. This parameter is sampled and not 100% tested. 6. A7 to A16 are page addresses and must be same within the page write operation. 7. See AC read characteristics.

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life TOGGLE BIT This device provides another function to determine the internal programming cycle. If the EEPROM is set to read mode during the internal programming cycle, I/O6 will charge from "1" to "0" (toggling) for each read. When the internal pro- gramming cycle is finished, toggling of I/O6 will stop and the device can be accessible for next read or program. TOGGLE BIT WAVEFORM NOTES: 1) I/O6 beginning state is "1". 2) I/O6 ending state will vary. 3) See AC read characteristics. 4) Any locations can be used, but the address must be fixed. Dout Dout DoutDout Din tCE tOE tOEH tWC tDW 4Next Mode tOES Address CE\\ WE\\ OE\\ I/O6 SOFTWARE DATA PROTECTION TIMING WAVEFORM (In protection mode) tWCtBLC {Address Data (each byte) 5555 AA AAAA or 2AAA 5555 Write Address* Write Data V CC CE\\ WE\\ tBLCtBLC * During this write cycle, data is physically written to the address provided.

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life SOFTWARE DATA PROTECTION TIMING WAVEFORM (In non-protection mode) FUNCTIONAL DESCRIPTION Automatic Page Write Page-mode write feature allows 1 to 128 bytes of data to be written into the EEPROM in a single write cycle. Following the initial byte cycle, an additional 1 to 128 bytes can be writ- ten in the same manner. Each additional byte load cycle must be started within 30µs from the preceding falling edge of WE\\ or CE\\. When CE\\ or WE\\ is kept high for 100µs after data input, the EEPROM enters write mode automatically and the input data are written into the EEPROM. DATA\\ Polling DATA\\ polling allows the status of the EEPROM to be deter- mined. If EEPROM is set to read mode during the write cycle, an inversion of the last byte of data to be loaded outputs from I/O's 7, 15, 23, and 31 to indicate that the EEPROM is per- forming a write operation. RDY/Busy\\ Signal RDY/Busy\\ signal also allows status of the EEPROM to be determined. The RDY/Busy\\ signal has high impedance ex- cept in write cycle and is lowered to V OL after the first write signal. At the end of write cycle, the RDY/Busy\\ signal changes state to high impedance. RES\\ Signal When RES\\ is low, the EEPROM cannot be read or pro- grammed. Therefore, data can be protected by keeping RES\\ low when V CC is switched. RES\\ should be high during read and programming because it doesn't provide a latch function. See timing diagram below. Program inhibit Program inhibit Read inhibitRead inhibit VCC RES\\ RES\\ Signal Diagram tWC Address Data (each byte) 5555 AA AAAA or 2AAA 5555 AAAA or 2AAA V CC CE\\ WE\\ 5555 AA 5555 Normal active mode

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life WE\\, CE\\ Pin Operation During a write cycle, address are latched by the falling edge of WE\\ or CE\\, and data is latched by the rising edge of WE\\ or CE\\. Write/Erase Endurance and Data Retention Time The endurance is 10 4 cycles in case of the page programming and 103 cycles in case of the byte programming (1% cumula- tive failure rate). The data retention time is more than 10 years when a device is page-programmed less than 104 cycles. RDY/Busy\\ SIGNAL RDY/Busy\\ signal also allows status of the EEPROM to be determined. The RDY/Busy\\ signal has high impedance except in write cycle and is lowered to VOL after the first write signal. At the end of the write cycle, the RDY/Busy\\ signal changes state to high impedance. This allows many 58C1001 devices RDY/Busy\\ signal lines to be wired-OR together. PROGRAMMING/ERASE The 58C1001 does NOT employ a BULK-erase function. The memory cells can be programmed ‘0’ or ‘1’. A write cycle performs the function of erase & write on every cycle with the erase being transparent to the user. The internal erase data state is considered to be ‘1’. To program the memory array with background of ALL 0’s or All 1’s, the user would program this data using the page mode write operation to program all 1024 128-byte pages. Data Protection 1. Data Protection against Noise on Control Pins (CE\\, OE\\, WE\\) During Operation During readout or standby, noise on the control pins may act as a trigger and turn the EEPROM to programming mode by mistake. To prevent this phenomenon, this device has a noise cancellation function that cuts noise if its width is 20ns or less in program mode. Be careful not to allow noise of a width more than 20ns on the control pins. See Diagram 1 below. 2. Data Protection at V CC On/Off When VCC is turned on or off, noise on the control pins generated by external circuits (CPU, etc.) may act as a trigger and turn the EEPROM to program mode by mistake. To prevent this unintentional programming, the EEPROM must be kept in an unprogrammable state while the CPR is in an unstable state. NOTE: The EEPROM should be kept in unprogrammable state during V CC on/off by using CPU RE- SET signal. See the timing diagram below. DIAGRAM 1 DATA PROTECTION AT VCC ON/OFF *Unprogrammable VCC CPU RESET *Unprogrammable

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life Data Protection Cont. a. Protection by RES\\ The unprogrammable state can be realized by the CPU's reset signal inputs directly to the EEPROM's RES pin. RES should be kept V SS level during VCC on/off. The EEPROM brakes off programming operation when RES becomes low, programming operation doesn't fin- ish correctly in case that RES falls low during programming operation. RES should be kept high for 10ms after the last data inputs. See the timing diagram below. 3. Software data protection To prevent unintentional programming, this device has the software data protection (SDP) mode. The SDP is enabled by inputting the 3 bytes code and write data in Chart 1. SDP is not enabled if only the 3 bytes code is input. To program data in the SDP enable mode, 3 bytes code must be input before write data. This 4th cycle during write is required to initiate the SDP and physically writes the address and data. While in SDP the entire array is protected in which writes can only occur if the exact SDP sequence is re-executed or the unprotect sequence is executed. The SDP is disabled by inputting the 6 bytes code in Chart 2. Note that, if data is input in the SDP disable cycle, data can not be written. The software data protection is not enabled at the shipment. NOTE: These are some differences between ASI's and other company's for enable/disable sequence of software data protection. If these are any questions, please contact ASI. PROTECTION BY RES\\ Program inhibit VCC RES\\ Program inhibit WE\\ or CE\\ 1µ min 100µ min 10 ms min CHART 1 Address 5555 AAAA or 2AAA 5555 Write Address Data (each Byte) AA Write Data} Normal data input CHART 2 Address 5555 AAAA or 2AAA 5555 5555 AAAA or 2AAA 5555 Data (each Byte) AA AA

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life ASI Case #703 (Package Designator Q) MECHANICAL DEFINITIONS* *All measurements are in inches. 4 x D2 4 x D1 4 x D b e Pin 1 MIN MAX A 0.123 0.200 A1 0.118 0.186 A2 0.000 0.020 b 0.013 0.017 B D D1 0.870 0.890 D2 0.980 1.000 D3 0.936 0.956 e R 0.005 L1 0.035 0.045 SYMBOL

0.010 REF

0.050 BSC

ASI PACKAGE SPECIFICATIONS

0.800 BSC

R B SEE DETAIL A A

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life ASI Case (Package Designator QB) MECHANICAL DEFINITIONS* *All measurements are in inches. 0.900 0.320 0.200 0.020 0.015 0.050 DETAIL A 0.035(+0.005) 0.008(+0.002) 0.015(+0.005)

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life *AVAILABLE PROCESSES IT = Industrial Temperature Range -40 oC to +85oC XT = Extended Temperature Range -55 oC to +125oC 883C = Full Military Processing -55 oC to +125oC

ORDERING INFORMATION

AS8ER128K32 Q -150 /* AS8ER128K32 Q -200 /* AS8ER128K32 Q -250 /* Device Number Package Type Speed ns Process AS8ER128K32 QB -150 /* AS8ER128K32 QB -200 /* AS8ER128K32 QB -250 /* EXAMPLE: AS8ER128K32Q-15/IT EXAMPLE: AS8ER128K32QB-250/XT

EEPROMEEPROMEEPROMEEPROMEEPROM AS8ER128K32 Austin Semiconductor, Inc. AS8ER128K32 Rev. 4.5 2/03 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. End Of Life ASI TO DSCC PART NUMBER CROSS REFERENCE* * ASI part number is for reference only. Orders received referencing the SMD part number will be processed per the SMD. Package Designator Q ASI Part # SMD Part AS8ER128K32Q-250/883C 5962-9458507HMX AS8ER128K32Q-200/883C 5962-9458508HMX AS8ER128K32Q-150/883C 5962-9458509HMX Package Designator QB ASI Part # SMD Part AS8ER128K32QB-250/883C 5962-9458507HZC AS8ER128K32QB-200/883C 5962-9458508HZC AS8ER128K32QB-150/883C 5962-9458509HZC