AS10515F16MIL AUSTIN | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Austin Semiconductor, Inc. AS10515F16MIL Rev. 2.0 11/01 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. For more products and information please visit our web site at www.austinsemiconductor.com AVAILABLE AS MILITARY SPECIFICATIONS

  • Military Equivalent Screening - 883 1.2.2 Quad Line Receiver PIN ASSIGNMENT (Top View) 16-Pin FlatPack (F) GENERAL DESCRIPTION The AS10515F16MIL is a quad differential amplifier designed for use in sensing differential signals over long lines. The base bias supply (V BB ) is made available at pin 9 to make the device useful as a Schmitt trigger, or in other applications where a stable reference voltage is necessary. Active current sources provide the AS10515F16MIL with excellent common mode noise rejection. If any amplifier in a package is not used, one input of that amplifier must be connected to V BB (pin 9) to prevent upsetting the current source bias network.
  • PD = 150mW Max/Pkg (No Load)
  • tpd = 2.0ns typ
  • tr, tf = 2.0ns type (20% - 80%) FUNCTION FLATS BURN-IN (CONDITION C) VCC1 5 GND AOUT 6 51 Ω to VTT BOUT 7 51 Ω to VTT AIN\\ 8 VBB AIN 9 GND BIN 10 GND BIN\\ 11 VBB VEE 12 VEE VBB 13 VBB C IN\\ 14 VBB C IN 15 GND D IN 16 GND D IN\\ 1 VBB C OUT 2 51 Ω to VTT D OUT 3 51 Ω to VTT VCC2 4 GND PIN ASSIGNMENTS BURN-IN CONDITIONS: V TT = -2.0V MAX/ -2.2V MIN V EE = -5.7V MAX/ -5.2V MIN V BB = All pins designated for VBB must be tied together, no external voltage applied. NOTES 1. VBB to be used to supply bias to the AS10515F16MIL only and bypassed (when used) with 0.01 µF to 0.1 µF capacitor. 2. When the input pin with the bubble goes positive, the output goes negative. D IN\\ C OUT D OUT V CC2 V CC1 A OUT B OUT A IN\\ D IN C IN C IN\\ V BB V EE B IN\\ B IN A IN LOGIC DIAGRAM 9VBB

Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.

  1. R1 = 50 Ω resistor in series with 50 Ω coax constituting the 100 Ω load.
  2. Unused outputs should be loaded 100 Ω to ground.

Figure 1. Switching Test Circuit and Waveforms rise and fall times of 2.0ns ± 0.2ns.

Austin Semiconductor, Inc. AS10515F16MIL Rev. 2.0 11/01 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. * ELECTRICAL CHARACTERISTICS Each MECL 10K series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 100 Ω resistor to -2.0 volts. QUIESCENT LIMIT TABLE* Connected to pin 9. * Measure voltage on pin 9 while it is connected to other pins. VIH1 VIL1 VIH2 VIL2 PS1 PS2 VEEL VEE VCB Test Voltage Values (Volts)Test Temperature SYMBOL PARAMETER UNITS MIN MAX MIN MAX MIN MAX VIH1 VIL1 VIH2 VIL2 VEE VCC * P.U.T. VOH High Output 11 - 13 2, 3 ,14, 15 VOL Low Output 11 - 13 2, 3 ,14, 15 VOH1 High Output 11 - 13 2, 3 ,14, 15 VOL1 Low Output 11 - 13 2, 3 ,14, 15 VBB Reference 11, 12 9 IEE Power Supply Current -26 -29 -29 mA 8 1, 16 5, 6 11, 12 8 IIH Input Current High 95 165 165 µA 4 - 7 10 - 13 8 1, 16 4 - 7 10 - 13 ICBO Input Leakage Current -1.0 -1.0 -1.5 µA 8 1, 16 4 - 7 10 - 13 4 - 7 10 - 13 LIMITS TEST VOLTAGE APPLIED TO PINS BELOW: Pinouts referenced are for F package, check Pin Assignments VCC = 0V, Output Load = 100 ΩΩΩΩ to -2.0VSubgroup 3Functional Parameters: +25°C Subgroup 1 +125°C Subgroup 2 -55°C

Austin Semiconductor, Inc. AS10515F16MIL Rev. 2.0 11/01 Austin Semiconductor, Inc. reserves the right to change products or specifications without notice. * ELECTRICAL CHARACTERISTICS Each MECL 10K series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 100 Ω resistor to -2.0 volts. QUIESCENT LIMIT TABLE* VIH1 VIL1 VIH2 VIL2 PS1 PS2 VEEL VEE VCB Test Voltage Values (Volts)Test Temperature SYMBOL PARAMETER UNITS MIN MAX MIN MAX MIN MAX VIN VOUT VCC VEEL P.U.T. tPHL Propagation Delay tPLH Propagation Delay Functional Parameters: +25°C Subgroup 9 LIMITS TEST VOLTAGE APPLIED TO PINS BELOW: Pinouts referenced are for F package, check Pin Assignments VCC = 2.0V, Output Load = 100 ΩΩΩΩ to GNDSubgroup 11 +125°C Subgroup 10 -55°C