ALN2450T2 ASB | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 4

Technical content

1/4 www.asb.co.kr May 2009 plerowTM ALN2450T2 Internally Matched LNA Module The plerow TM ALN-series is the compactly designed surface-mount module for the use of the LNA with or without the following gain blocks in the infrastructure equipment of the mobile wireless (CDMA, GSM, PCS, PHS, WCDMA, DMB, WLAN, WiBro, WiMAX), GPS, satellite communi- cation terminals, CATV and so on. It has an exceptional performance of low noise figure, high gain, high OIP3, and low bias current. The stability factor is always kept more than unity over the application band in order to ensure its unconditionally stable implementation to the application system environment. The surface-mount module package including the completed matching circuit and other components necessary just in case allows very simple and convenient implementation onto the system board in mass production level. Specifications Parameter Unit Min Typ Max Frequency Range MHz 2300 2600 Gain dB 27 28 Gain Flatness dB ± 1.0 ± 1.1 Noise Figure dB 0.90 1.0 Output IP3 (1) dBm 33 34 S11 / S22 (2) dB -18 / -12 Output P1dB dBm 17 18 Switching Time (3) µsec 0.75 1.5 Supply Current mA 90 100 Supply Voltage V 5 Impedance Ω 50 Max. RF Input Power dBm C.W 29 ~ 31 (before fail) Package Type & Size mm Surface Mount Type, 10Wx10Lx3.8H Operating temperature is -40°C to +85°C. 1) OIP3 is measured with two tones at an output power of 4 dBm / tone separated by 1 MHz. 2) S11/S22 (max) is the worst value within the frequency band. 3) Switching time means the time that takes for output power to get stabilized to its final level after switching DC voltage from 0 V to V Pin Number Function

2 RF In

5 RF Out

Outline Drawing (Unit: mm)

  • S 21 = 29 dB @ 2300 MHz = 27 dB @ 2600 MHz
  • NF of 0.90 dB over Frequency
  • Unconditionally Stable
  • Single 5V Supply
  • High OIP3 @ Low Current Note: 1. The number and size of ground via holes in a circuit board is critical for thermal RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of all ground pins fo r better RF and thermal performance, as shown in the drawing at the left side. (Recommended Footprint) ALN2450T2 ASB Inc. (Top View) (Bottom View) Ø0.4 plated thru holes to ground plane plerow (Side View) Solder Stencil Area Website: www.asb.co.kr E-mail: sales@asb.co.kr Tel: (82) 42-528-7223 Fax: (82) 42-528-7222 ASB Inc., 4th Fl. Venture Town Bldg., 367-17 Goijeong-Dong, Seo-Gu, Daejon 302-716, Korea More Information 2-stage Single Type Specifications (in Production) Typ. @ T = 25°C, Vs = 5 V, Freq. = 2450 MHz, Zo.sys = 50 ohm Features Description

2/4 www.asb.co.kr May 2009 plerowTM ALN2450T2 Internally Matched LNA Module S-parameters Noise Figure OIP3 P1dB 2300~2600 +5 V Typical Performance (Measured) S-parameters & K Factor

3/4 www.asb.co.kr May 2009 plerowTM ALN2450T2 Internally Matched LNA Module Switching Time

4/4 www.asb.co.kr May 2009 plerowTM ALN2450T2 Internally Matched LNA Module 1) The tantal or MLC (Multi Layer Ceramic) capacitor is optional and for bypassing the AC noise introduced from the DC supply. The capacitance value may be determined by customer’s DC supply status. The ca- pacitor should be placed as close as possible to V s pin and be connected directly to the ground plane for the best electrical performance. 2) DC blocking capacitors are always necessarily placed at the input and output port for allowing only the RF signal to pass and blocking the DC component in the signal. The DC blocking capacitors are in- cluded inside the ALN module. Therefore, C1 & C2 capacitors may not be necessary, but can be added just in case that the customer wants. The value of C1 & C2 is determined by considering the application frequency. Application Circuit Recommended Soldering Reflow Process 20~40 sec 260°C 200°C 150°C 60~180 sec Ramp-up (3˚C/sec) Ramp-down (6°C/sec) + - ALN OUT IN C1 C2 VS Tantal or MLC (Multi Layer Ceramic) Capacitor IN OUT Vs Size 25x25mm (for ALN-AT, BT, T Series – 10x10mm) Evaluation Board Layout