ACL4300T2_17 ASB | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 4
Technical content
1/4 www.asb.co.kr August 2017 plerowTM ACL4300T2 Internally Matched LNA Module The plerow TM ACL-series is the compactly designed surface-mount module for the use of the LNA with or without the following gain blocks in the infrastructure equipment of the mobile wireless (CDMA, GSM, PCS, PHS, WCDMA, DMB, WLAN, WiBro, WiMAX), GPS, satellite commun i- cation terminals, CATV and so on. It has an exceptional performance of low noise figure, high gain, high OIP3, and low bias current. The stability factor is always kept more than unity over the application band in order to ensure its unconditionally stable implementation to the application system environment. The surface -mount module package including the completed matching circuit and other components necessary just in case allows very simple and convenient implementation onto the system board in mass production level. Parameter Unit Specifications Min Typ Max Frequency Range MHz 4200 4400 Gain dB 19 20 Gain Flatness dB 0.9 1.0 Noise Figure dB 1.25 1.30 Output IP3 (1) dBm 29 30 S11 / S22 (2) dB -18 / -10 Output P1dB dBm 13 14 Switching Time (3) sec - Supply Current mA 50 60 Supply Voltage V 5 Impedance 50 Package Type & Size mm Surface Mount Type, 10Wx10Lx3.8H Operating temperature is -40C to +85C. 1) OIP3 is measured with two tones at an output power of 4 dBm / tone separated by 1 MHz. 2) S11/S22 (max) is the worst value within the frequency band. 3) Switching time means the time that takes for output power to get stabilized to its final level after switching DC voltage from 0 V to VS. Pin Number Function
2 RF In
5 RF Out
Outline Drawing (Unit: mm)
- S21 = 20.9 dB @ 4200 MHz = 19.1 dB @ 4400 MHz
- NF of 1.25 dB over Frequency
- Unconditionally Stable
- Single 5V Supply
- High OIP3 @ Low Current Note: 1. The number and size of ground via holes in a circuit board is critical for thermal RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of all ground pins for better RF and thermal performance, as shown in the drawing at the left side. (Recommended Footprint) ACL4300T2 ASB Inc. (Top View) (Bottom View) Ø 0.4 plated thru holes to ground plane plerow (Side View) Solder Stencil Area Website: www.asb.co.kr E-mail: sales@asb.co.kr Tel: (82) 42-528-7223 Fax: (82) 42-528-7222 More Information 2-stage Single Type Specifications (in Production) Typ. @ T = 25C, Vs = 5 V, Freq. = 4300 MHz, Zo.sys = 50 ohm Features Description
2/4 www.asb.co.kr August 2017 plerowTM ACL4300T2 Internally Matched LNA Module S-parameters Noise Figure OIP3 P1dB 4200~4400 MHz +5 V Typical Performance (Measured) S-parameters & K Factor
3/4 www.asb.co.kr August 2017 plerowTM ACL4300T2 Internally Matched LNA Module 1. S-parameter 2. OIP3, P1dB & NF Note: tested at room temperature. 1. S-parameter 2. OIP3, P1dB & NF Note: tested at Vs= 5V.
4200 MHz 4300 MHz 4400 MHz
S21 (dB) S11 (dB) S22 (dB) S21 (dB) G/F (dB) S11 (dB) S22 (dB) S21 (dB) S11 (dB) S22 (dB) OIP3 (dBm) P1dB (dBm) NF (dB) OIP3 (dBm) P1dB (dBm) NF (dB) OIP3 (dBm) P1dB (dBm) NF (dB) S21 (dB) S11 (dB) S22 (dB) S21 (dB) G/F (dB) S11 (dB) S22 (dB) S21 (dB) S11 (dB) S22 (dB) OIP3 (dBm) P1dB (dBm) NF (dB) OIP3 (dBm) P1dB (dBm) NF (dB) OIP3 (dBm) P1dB (dBm) NF (dB) RF Performance with Operating Temperature RF Performance with Voltage Change
4/4 www.asb.co.kr August 2017 plerowTM ACL4300T2 Internally Matched LNA Module 1) The tantal or MLC (Multi Layer Ceramic) capacitor is optional and for bypassing the AC noise introduced from the DC supply. The capacitance value may be determined by customer’s DC supply status. The ca- pacitor should be placed as close as possible to Vs pin and be connected directly to the ground plane for the best electrical performance. 2) DC blocking capacitors are always necessarily placed at the input and output port for allowing only the RF signal to pass and blocking the DC component in the signal. The DC blocking capacitors are inclu d- ed inside the ALN module. Therefore, C1 & C2 capacitors may not be necessary, but can be added just in case that the customer wants. The value of C1 & C2 is det ermined by considering the application fre- quency. Copyright 2009-2017 ASB Inc. All rights reserved. Datasheet subject to change without notice. ASB assumes no re- sponsibility for any errors which may appear in this datasheet. No part of the datasheet may be copied or reproduced in any form or by any means without the prior written consent of ASB. Application Circuit Recommended Soldering Reflow Process 20~40 sec 260C 200C 150C 60~180 sec Ramp-up (3˚C/sec) Ramp-down (6C/sec) + - ACL OUT IN C1 C2 VS Tantal or MLC (Multi Layer Ceramic) Capacitor IN OUT Vs Size 25x25mm (for ACL-T Series – 10x10mm) Evaluation Board Layout