855549

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

242.625 MHz SAW Filter

Data Sheet: Rev - 5/31/11 - 1 of 6 - Disclaimer: Subject to change without notice e © 2011 TriQuint Semiconductor, Inc. Connecting the Digital World to the Global Network ®

Applications

Typical 1dB bandwidth of 1.3 MHz Low loss High Attenuation Single-ended operation Ceramic Surface Mount Package (SMP) Small Size Dimensions: 19.00 x 6.50 x 1.75mm Hermetically sealed RoHS compliant, Pb-free 10 9 8 7 6 54321 Input Gnd Output GndGndGnd GndGndGndGnd General Description Pin Configuration The 855 549 is a high -performance IF SAW filter with a center frequency of 242.625 MHz and a 1dB bandwidth of 1.3 MHz. It features low loss with excellent attenuation, and is designed to be used with a single ended input and output. This device is RoHS compliant and Pb-free. Pin # SE Description

10 Input

5 Output

1,6 Ground 2,3,4,7,8,9 Case ground

Ordering Information

Part No. Description 855549 packaged part 855549-EVB evaluation board Standard T/R size = 2000 units/reel.

Data Sheet: Rev - 5/31/11 - 2 of 6 - Disclaimer: Subject to change without notice e © 2011 TriQuint Semiconductor, Inc. Connecting the Digital World to the Global Network ® Specifications Electrical Specifications (1) Specified Temperature Range: (2) +25 ºC Parameter (3) Conditions Min Typical (4) Max Units Center Frequency - 242.625 - MHz Minimum Insertion Loss - 18.7 11 dB 1.0 dB Lower Bandedge (5) - 242.006 242.125 MHz 1.0 dB Upper Bandedge (5) 243.125 243.310 - MHz Passband Ripple (6) (over 100% of 1dB bandwidth) - 0.62 0.75 dB p-p Phase Ripple 242.5 – 242.751 MHz - 1.4 5 deg p-p Relative Attenuation (5) 20 – 240.151 MHz 245.15 – 465.25 MHz dB dB Source Impedance (single-ended) (7) - - 50 - Load Impedance (single-ended) (7) - - 50 - Notes: 1. All specifications are based on the TriQuint schematic for the main reference design shown on page 3 2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature 3. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances 4. Typical values are based on average measurements at room temperature 5. Relative to Minimum Insertion Loss 6. Passband Ripple is defined as the worst case difference between a peak and an adjacent valley within defined frequency points 7. This is the optimum impedance in order to achieve the performance shown Absolute Maximum Ratings Parameter Rating Operating Temperature(8) -40 to +85 oC Storage Temperature -40 to +85 oC 8. Device may operate over this range with degraded Electrical Specifications Operation of this device outside the parameter ranges given above may cause permanent damage.

Data Sheet: Rev - 5/31/11 - 3 of 6 - Disclaimer: Subject to change without notice e © 2011 TriQuint Semiconductor, Inc. Connecting the Digital World to the Global Network ® Reference Design – 50 SE Input, 50 SE Output Schematic Single-ended Input 1,2,3,4 6,7,8,9 43nH 10 5 43nH 47pF 47pF Single-ended Output Notes: 1. Actual matching values may vary due to PCB layout and parasitics PC Board Mounting Configuration 960656 XXXX SAWTEK 855549 2.51 6.70 8.86 .69 1.222.00 Notes: Top, middle & bottom layers: 1 oz copper Substrates: FR4 dielectric, .031” thick Finish plating: Nickel: 3-8µm thick, Gold: .03-.2µm thick Hole plating: Copper min .0008µm thick Notes: 1. All dimensions are in millimeters. 2. This footprint represents a recommendation only. Bill of Material Reference Desg. Value Description Manufacturer Part Number L1 43nH Coil Wire-wound, 0805, 5% Coilcraft 0805CS-431XJLC L2 43nH Coil Wire-wound, 0805, 5% Coilcraft 0805CS-431XJLC C1 47pF Chip Capacitor, 0805, 5% MuRata GRM2165C1H470JZ01 C2 47pF Chip Capacitor, 0805, 5% MuRata GRM2165C1H470JZ01 SMA N/A SMA connector Radiall USA Inc. 9602-1111-018 PCB N/A 3-layer multiple 960656

Data Sheet: Rev - 5/31/11 - 4 of 6 - Disclaimer: Subject to change without notice e © 2011 TriQuint Semiconductor, Inc. Connecting the Digital World to the Global Network ® Typical Performance (at room temperature)

Data Sheet: Rev - 5/31/11 - 5 of 6 - Disclaimer: Subject to change without notice e © 2011 TriQuint Semiconductor, Inc. Connecting the Digital World to the Global Network ® Mechanical Information Package Information, Dimensions and Marking Date Code ID Dot R0.51 1.91 2.31 1.02 1.80 0.76 19.0 6.50 1.75 NOM. 1.96 MAX. XXXX SAWTEK 855549 Package Style: SMP-75 Dimensions: 19.00 x 6.50 x 1.75mm Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 0.5 - 1.0μm, over a 2-6μm Ni plating All dimensions shown are nominal in millimeters All tolerances are ±0.15mm except overall length and width ±0.10mm Tape and Reel Information Standard T/R size = 2000 units/reel. All dimensions are in millimeters ID dot Direction of travel Ø330 Ø102 2.7 Ø13.0 Ø20.2 2.0 32.8 Ø1.5 12.02.3 4.00.3 2.0 0.20 Section A-A 7.1 19.6 R0.75 1.75 Ø1.5 14.2 28.4 32.0 A A

Data Sheet: Rev - 5/31/11 - 6 of 6 - Disclaimer: Subject to change without notice e © 2011 TriQuint Semiconductor, Inc. Connecting the Digital World to the Global Network ® Product Compliance Information ESD Information ESD Rating: 2 Value: Passes 2000 V min. Test: Human Body Model (HBM) Standard: JEDEC Standard JESD22-A114 ESD Rating: C Value: Passes 500 V min. Test: Machine Model (MM) Standard: JEDEC Standard JESD22-A115 Solderability Compatible with th e latest version of J -STD-020, l ead free solder, 260°C Refer to Soldering Profile for recommended guidelines. This part is compliant with EU 2002/95/EC RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment). This product also has the following attributes: Halogen Free (Chlorine, Bromine) Antimony Free TBBP-A (C15H12Br402) Free PFOS Free SVHC Free MSL Rating Devices are Hermetic, therefore MSL is not applicable. Contact Information For the latest specifications, additional product information, worldwide sales and distribution locations, and information ab out TriQuint: Email: info-sales@tqs.com Fax: +1.407.886.7061 For technical questions and application information: Email: applications.engineering@tqs.com Important Notice The information contained herein is believed to be reliable . TriQuint makes no warranties regarding the information contain herein. TriQuint assumes no res ponsibility or liability whatsoever for any of the information contained her ein. TriQuint assumes no responsibility or liability whatsoever for the use of the information contained herein. The information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with the user. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for TriQuint products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual pro perty rights, whether with regard to such information itself or anything described by such information. TriQuint products are not warranted or authorized for use as critical components in medical, life -saving, or life -sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. Caution! ESD-Sensitive Device