5060290 CLARKE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 12
Technical content
OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC12/23 DIGITAL TYRE INFLATOR MODEL NO: CTIDG2 PART NO: 5060290
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for purchasing this CLARKE Tyre Inflator. The CTIDG2 can be used for inflating car, motorcycle and bicycle tyres. The tyre inflator is not waterproof and should not be used in any wet applications. Before attempting to use the product it is essential that you read this manual thoroughly and carefully follow all instructions given. In doing so you will ensure the safety of yourself and that of others around you and you can also look forward to the product giving you long and satisfactory service After removing the tyre inflator from its packaging, check that it has not been damaged in transit. Report any damage immediately to the CLARKE dealer where the item was purchased. PRODUCT SPECIFICATIONS Model CTIDG2 Hose length 500mm Max supply pressure 200psi Max inflation pressure 174 psi Max flow rate 500L/min @188psi Accuracy +/- 2psi @ 25-75psi Ingress protection IP44 Units of measurement psi, kPa, bar Working temperature 10 to 50oC Dimensions (L x W x H) 890 x 85x 45 mm Weight 0.85 kg Inlet size 1/4 “ BSP Auto-Off 9 seconds Battery Type 2 x AAA (included)
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com GENERAL SAFETY WARNINGS PERSONAL SAFETY 1. ALWAYS thoroughly familiarise yourself with this product and its operation and always read the instructions in this manual before using the product. 2. ALWAYS stay alert, watch what yo u are doing and use common sense when operating the tyre inflator. DO NOT use while you are tired or under the influence of medication, drugs or alcohol. A moment of inattention can result in personal injury. WORKING CONDITIONS 1. DO NOT use the tyre inflator in a damp or wet environment. 2. DO NOT cover the tyre inflator. 3. ALWAYS use the tyre inflator in spaces with good all-round air ventilation and that the air intake air is dry and dust free. 4. Keep the work area clean and well lit . Floors should always be kept clear. Cluttered or dark areas invite accidents. 5. NEVER over-reach. Keep your proper footing and balance at all times to enable better control of the tyre inflator in unexpected situations. 6. ALWAYS use in a safe area away from traffic and other hazards. GENERAL PRODUCT USE AND CARE 1. NEVER attempt to modify the fittings or attachments in any way. Doing so will invalidate the guarantee and could result in personal injury. 2. ALWAYS take care to maintain tyres to vehicle manufacturer’s recommended pressures. 3. ALWAYS store the tyre inflator at mo derate temperature and out of reach of children. 4. NEVER use this product if it appears de fective or is operating abnormally: If the tyre inflator operates unusually or makes strange noises, switch off immediately. Arrange repairs by your CLARKE dealer. 5. NEVER attempt any repairs yourself . If you have a technical problem contact your local CLARKE dealer. WARNING: WHEN USING BATTERY POWERED TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY. PLEASE READ ALL THE SAFETY AND OPERATING INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 6. NEVER throw the product away with house hold waste or allow it to fall into a fire. AIRLINE SAFETY PRECAUTIONS 1. Compressed air can be dangerous. En sure that you are thoroughly familiar with all precautions relating to the use of compressors and a compressed air supply. 2. NEVER direct a jet of compressed air at people or animals. 3. ALWAYS ensure that the equipment/tool being used has a safe working pressure exceeding the output pressure of the compressor that it is connected to. 4. NEVER exceed the operating pres sure stated in the specification. 5. ALWAYS ensure that the air supply is turned off and vent all compressed air from the air hose and the equipment attached to it before disconnecting air hoses or other equipment from your compressor. 6. Ensure all fixed air connections are prop erly sealed using ptfe tape or pipe sealant. 7. Check the airline pressure gauge period ically for accuracy and replace if damaged or inaccurate. ENVIRONMENTAL RECYCLING POLICY By purchasing this product, the customer is taking on the obligation to comply with current WEEE regulations. This means that this product must not be disposed of with general household waste. It must be disposed of according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal facility. This product contains valuable raw materials. Metal products should be taken to your local civic amenity site for recycling of metal products. The batteries fall under the Waste Batteries and Accumulators Regulations 2009 and should be disposed of in a controlled manner.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com PREPARATION FITTING THE BATTERIES The inflator requires 2 x AAA batteries. If the voltage of the batteries falls below 2.6 volts, the battery icon will flash continuously until it shuts down. If the voltage of the batteries falls below 2.5 volts the LOW “LO” battery icon appears while the power is on and then shuts down automatically. The batteries must be changed if the battery icon flashes. 1. Unscrew the battery cap. 2. Slide the batteries into the tyre inflator with the positive end facing outwards. 3. Replace the battery cap carefully and DO NOT over tighten.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com CONNECTING THE AIRLINE 1. Attach the airline hose to the tyre inflator and fully tighten. Use PTFE tape if needed. Turn on the air supply and check that the airline pressure does not exceed 13.8 bar (200 psi). 2. Ensure all fixed air connections are prop erly sealed using PTFE tape or pipe sealant. AIRLINE ACCESSORIES AND EQUIPMENT An extensive range of airline equipment is available from your CLARKE dealer including hoses, retractable hose reels, filter/regulators, in-line regulators, pressure gauges and safety goggles. THE DISPLAY PANEL Press and hold the button on the front of the unit to activate. Once activated, press and hold the button for 2 seconds to change the unit of measurement to either psi, kPa or bar. The display panel will illuminate and display as shown. The display should time out and switch off after 9 seconds. CAUTION: THIS PRODUCT MAY HAVE A LOWER WORKING PRESSURE THAN SOME COMPRESSORS WILL SUPPLY, THEREFORE, AN AIRLINE REGULATOR SHOULD BE INSTALLED. CAUTION: AIRLINE LUBRICATORS SHOULD NOT BE USED WITH THIS ITEM. CAUTION: ALWAYS USE DRY FILTERED COMPRESSED AIR & AVOID UNDUE EXPOSURE TO MOISTURE.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com OPERATION Under or over inflated tyres are dangerous. Consult the vehicle owners handbook before using this tyre inflator. Never exceed the maximum pressure of the tyre. 1. Remove the dust cap from the tyre va lve and check that the tyre valve is clean before connecting. 2. Push the connector fully home onto the tyre valve. If the valve leaks, the connector may need repositioning. Correct position is confirmed by a steady reading on the gauge. 3. When connected correctly, the display will show the current pressure in the tyre. If this is the correct tyre pressure as stated in your vehicle handbook, remove the valve connector. 4. Check the tyre pressure on the display. 5. Depress the trigger to inflate the tyre . Re-check the tyre pressure. Note that when the trigger is depressed, the gauge will show the airline pressure, not the tyre pressure. 6. To deflate the tyre, pa rtially depress the trigger and check the pressure again. 7. When the tyre pressure is correct, re move the connector. Replace the dust cap on the tyre valve. IMPORTANT: The air pressure gauge on this product is for guidance only. It is important that you check the pressure with an approved, calibrated gauge. 8. DO NOT use damaged or leaking hose s. Occasionally clean the product and lubricate the trigger parts if required.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com COMMON INFLATION PRESSURES CARE & MAINTENANCE Keep the tyre inflator free of dirt and dust as far as possible. Wipe with a clean cloth or blow it down with compressed air at low pressure. DO NOT use cleaning agents or solvents as these may be aggressive to the plastic parts. Ensure that no water can get into the interior of the tyre inflator. Your tyre inflator has been designed to give long and trouble free service. If, however, having followed the instructions in this booklet carefully, you encounter problems, take the item to your local CLARKE dealer. Store the tyre inflator in a dry location. USEFUL ACCESSORIES Various airline components are available from your CLARKE dealer including: Airline hoses (available in 10Mtr/15mtr lengths) Recoil hose (available in 7.6 and 15 mtr lengths) Hose reels Airline fittings such as filters, regulators, connectors See also the extensive range of CLARKE compressors and air tools. PSI KPA BAR Car 35 - 50 240 - 350 2.4 - 3.5 Motorcycle 26 - 40 180 - 275 1.8 - 2.75 Bicycle 35 - 100 240 - 690 2.4 - 6.9
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com COMPONENT PARTS No Description No Description 1R u b b e r s l e e v e 8T r i g g e r
2 Battery cover 9 Trigger valve assembly
3 Valve housing 10 Main body
4 Transparent cover 11 Air hose assembly
5 Button 12 Battery housing
6 Circuit board support 13 Battery (AAA)
7 Printed circuit board 14 Air nozzle
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY - UK
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY - CE