407-BBYS-C

407-BBYS-C ATGBICS

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 6

Technical content

ATGBICS® All rights reserved. EOE Ref: ATGBICS_407-BBYS-C_V1 Page 1 of 6 Product Datasheet 407-BBYS-C Dell® Compatible 10GBase-T SFP+ Transceiver Hot Pluggable, +3.3V, Cat 6a/7 Cable, up to 30m

FEATURES

• Supports 10GBase-T / 5GBase-T / 2.5GBase-T / 1000base-T
• Hot-pluggable SFP footprint
• Supports Links up to 30m using Cat 6a/7 Cable
• SFF-8431 and SFF-8432 MSA Compliant
• IEEE 802.3az Compliant
• Low Power Consumption (2.5W MAX @ 30m)
• Fast Retrain EMI Cancellation Algorithm
• Low EMI Emissions
• I2C 2-Wire Interface for Serial ID and PHY Register Access
• Auto-negotiates with other 10GBase-T PHYs
• Supports 100/1000Base-T using Cat 5e cable or better
• MDI/MDIX Crossover
• Multiple Loopback Modes for Testing and Troubleshooting
• Built-in Cable Monitoring and Link
• Cable Length Measurements
• Robust Die Cast Housing
• Bail Latch Style ejector mechanism
• Unshielded and Shielded cable support

DESCRIPTION

ATGBICS® Compatible 407-BBYS-C copper transceiver module is a high-performance integrated duplex data link for bi-directional communication over copper cable. It is specifically designed for high- speed communication links that require 10 Gigabit Ethernet over Cat 6a/7. SFP+-10GBASE-T Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA). They are compatible with the 10GBase-T / 5GBase-T / 2.5GBase-T / 1000base-T standards as specified in IEEE Std 802.3. SFP+-10GBASE-T uses the SFP's RX_LOS pin for link indication. If pull up SFP's TX_DISABLE pin, PHY IC be reset.

ATGBICS® All rights reserved. EOE Ref: ATGBICS_407-BBYS-C_V1 Page 2 of 6 Product Datasheet CABLE LENGTH SFP TO HOST CONNECTOR PIN OUT Pin Symbol Name/Description Ref.

1 VEET Transmitter Ground (Common with Receiver Ground) 1

2 TFAULT Transmitter Fault. Not supported. 3 TDIS Transmitter Disable. Laser output disabled on high or open. 2 4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. 3 5 MOD_DEF(1) Module Definition 1. Clock line for Serial ID. 3 6 MOD_DEF(0) Module Definition 0. Grounded within the module. 3

7 Rate Select No connection required

8 LOS High indicates no linked. low indicates linked. 4

9 VEER Receiver Ground (Common with Transmitter Ground) 1

10 VEER Receiver Ground (Common with Transmitter Ground) 1

11 VEER Receiver Ground (Common with Transmitter Ground) 1

12 RD- Receiver Inverted DATA out. AC Coupled 13 RD+ Receiver Non-inverted DATA out. AC Coupled

14 VEER Receiver Ground (Common with Transmitter Ground) 1

15 VCCR Receiver Power Supply

16 VCCT Transmitter Power Supply

17 VEET Transmitter Ground (Common with Receiver Ground) 1

18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in. AC Coupled.

20 VEET Transmitter Ground (Common with Receiver Ground) 1

Notes: 1. Circuit ground is connected to chassis ground 2. PHY disabled on TDIS > 2.0V or open, enabled on TDIS < 0.8V MOD_DEF(0) pulls line low to indicate module is plugged in. 4. LVTTL compatible with a maximum voltage of 2.5V. Standard Cable Reach Host Port 10GBase-T CAT6A 30m XFI 5GBase-T/2.5GBase-T CAT5E 50m 5GBase- R/2.5GBase-X 1000base-T CAT5E 100m 1000base-FX

Figure 1. Diagram of host board connector block pin numbers and names

ATGBICS® All rights reserved. EOE Ref: ATGBICS_407-BBYS-C_V1 Page 4 of 6 Product Datasheet LOW-SPEED SIGNALS MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals (see section VII, "Serial Communication Protocol"). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc Low-Speed Signals, Electronic Characteristics HIGH-SPEED ELECTRICAL INTERFACE All high-speed signals are AC-coupled internally. Parameter Symbol Min Max unit Notes/Conditions SFP Output LOW VOL 0 0.5 V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector SFP Output HIGH VOH host_Vcc - 0.5 host_Vcc + 0.3 V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector SFP Input LOW VIL 0 0.8 V 4.7k to 10k pull-up to Vcc, measured at SFP side of connector SFP Input HIGH VIH 2 Vcc + 0.3 V 4.7k to 10k pull-up to Vcc, measured at SFP side of connector High-Speed Electrical Interface, Transmission Line-SFP Parameter Symbol Min Typ Max unit Notes/Conditions Line Frequency fL 125 MHz 5-level encoding, per IEEE 802.3 Tx Output Impedance Zout,TX 100 Ohm Differential, for all frequencies between 1MHz and 125MHz Rx Input Impedance Zin,RX 100 Ohm Differential, for all frequencies between 1MHz and 125MHz

ATGBICS® All rights reserved. EOE Ref: ATGBICS_407-BBYS-C_V1 Page 5 of 6 Product Datasheet GENERAL SPECIFICATIONS Notes: 1. Clock tolerance is +/- 50 ppm ENVIRONMENTAL SPECIFICATIONS Automatic crossover detection is enabled. External crossover cable is not required SERIAL COMMUNICATION PROTOCOL All SFPs support the 2-wire serial communication protocol outlined in the SFP MSA. These SFPs use an MCU, can be accessed with address of A0h. High-Speed Electrical Interface, Host-SFP Parameter Symbol Min Typ Max unit Notes/Conditions Single ended data input swing Vinsing 250 1200 mV Single ended Single ended data output swing Voutsing 350 800 mV Single ended Rise/Fall Time Tr,Tf 175 psec 20%-80% Tx Input Impedance Zin 50 Ohm Single ended Rx Output Impedance Zout 50 Ohm Single ended General Parameter Symbol Min Typ Max unit Notes/Conditions Data Rate BR 1 10 Gb/sec IEEE 802.3 compatible. See Notes 1,2 below Parameter Symbol Min Typ Max unit Notes/Conditions Operating Temperature Top 0 65 °C Case temperature Storage Temperature Tsto -40 85 °C Ambient temperature Parameter Symbol Min Typ Max unit Notes/Conditions I 2C Clock Rate 0 200,00 Hz

ATGBICS® All rights reserved. EOE Ref: ATGBICS_407-BBYS-C_V1 Page 6 of 6 Product Datasheet MECHANICAL SPECIFICATIONS (UNIT:MM)