HMC387MS8_08 HITTITE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

Features

Input IP3: +32 dBm Conversion Loss: 9.5 dB Low External Part Count Ultra Small MSOP8 Package: 14.8 mm Included in the HMC-DK003 Designer’s Kit Electrical Specifi cations, TA = +25°C, LO = +17 dBm, IF = 70 MHz [1] Typical Applications High Dynamic Range Infrastructure:

  • GSM 450 & GSM 480
  • CDMA 450
  • Private Land Mobile Radio The HMC387MS8 & HMC387MS8E are high dynamic range passive MMIC mixers in plastic surface mount 8 lead Mini Small Outline Packages (MSOP) covering 450 to 500 MHz. Excellent input IP3 performance of +32 dBm for down conversion and +29 dBm for u p c o n v e r s i o n i s p r o v i d e d f o r b o t h G S M / C D M A based cellular and Private Land Mobile Radio applications at an LO drive of +17 dBm. The mixer also has excellent performance with as little as +13 dBm LO drive yielding a +30 dBm input IP3. With a 1 dB compression of +22 dBm, the RF port will accept a wide range of input signal levels. C o n v e r s i o n l o s s i s 9 . 5 d B t y p i c a l . T h e D C t o 1 5 0 MHz IF frequency response will satisfy many cel- lular transmit or receive frequency plans. The HMC387MS8(E) input IP3 performance coupled with its high P1dB rivals traditional active FET mixers while offering a much smaller 14.8mm 2 standard IC footprint and no DC bias. Parameter Min. Typ. Max. Units Frequency Range, RF 450 - 500 MHz Frequency Range, LO [2] 300 - 500 MHz Frequency Range, IF DC - 150 MHz Conversion Loss 9.5 11 dB Noise Figure (SSB) 9.5 11 dB LO to RF Isolation 17 20 dB LO to IF Isolation 20 23 dB IP3 (Input) 29 32 dBm 1 dB Gain Compression (Input) 19 22 dBm LO Input Drive Level (Typical) +13 to +19 dBm [1] Unless otherwise noted, all measurements performed as a downconverter with low side LO & IF = 70 MHz [2] LO Frequency optimized. See application circuit herein. HMC387MS8 / 387MS8E

For price, delivery, and to place orders, please contact Hittite Microwave Corporation:

20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373

Order On-line at www.hittite.com Conversion Gain vs. Temperature @ LO = +17 dBm Isolation @ LO = +17 dBm Conversion Gain vs. LO Drive Return Loss @ LO = +17 dBm IF Bandwidth @ LO = +17 dBm Upconverter Conversion Gain vs. LO Drive -20 -15 -10 +25 C +85 C -40 C CONVERSION GAIN (dB) RF FREQUENCY (GHz) -50 -40 -30 -20 -10 RF TO IF LO TO RF LO TO IF ISOLATION (dB) FREQUENCY (GHz) -20 -15 -10 LO= +13dBm LO=+ 15dBm LO= +17dBm LO= +19dBm CONVERSION GAIN (dB) RF FREQUENCY (GHz) -20 -15 -10 LO RF RETURN LOSS (dB) RF FREQUENCY (GHz) -20 -15 -10 50 100 150 200 250 300 350 CONVERSION GAIN RETURN LOSS IF FREQUENCY (MHz) RESPONSE (dB) -20 -15 -10 0.45 0.5 0.55 0.6 LO = +13 dBm LO = +15 dBm LO = +17 dBm LO = +19 dBm CONVERSION GAIN (dB) RF FREQUENCY (GHz) HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz v02.0705 HMC387MS8 / 387MS8E

For price, delivery, and to place orders, please contact Hittite Microwave Corporation: Order On-line at www.hittite.com Input IP3 vs. LO Drive IF = 70 MHz Input IP3 vs. LO Drive IF = 137 MHz Input IP3 vs. LO Drive IF = 97 MHz Input IP3 vs. Temperature IF = 70 MHz, LO = +17 dBm Input IP3 vs. LO Drive IF = 117 MHz Upconverter Input IP3 vs. LO Drive IF = 70 MHz +25 C +85 C -40 C INPUT IP3 (dBm) RF FREQUENCY (GHz) LO= +13 dBm LO= +15 dBm LO= +17 dBm LO= +19 dBm INPUT IP3 (dBm) RF FREQUENCY (GHz) LO= +13 dBm LO= +15 dBm LO= +17 dBm LO= +19 dBm INPUT IP3 (dBm) RF FREQUENCY (GHz) LO= +13dBm LO= +15dBm LO= +17dBm LO= +19dBm INPUT IP3 (dBm) RF FREQUENCY (GHz) LO= +13dBm LO= +15dBm LO= +17dBm LO= +19dBm INPUT IP3 (dBm) RF FREQUENCY (GHz) LO= +13 dBm LO= +15 dBm LO= +17 dBm LO= +19 dBm INPUT IP3 (dBm) RF FREQUENCY (GHz) HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz v02.0705 HMC387MS8 / 387MS8E

For price, delivery, and to place orders, please contact Hittite Microwave Corporation: Order On-line at www.hittite.com Input IP2 vs. LO Drive Input IP2 vs. Temperature @ LO = +17 dBm MxN Spurious Outputs nLO m R F 01234 0x x - 5 1 3 1 36 11 . 502 7 2 5 4 2 25 4 6 5 4 7 5 3 6 1 38 3 7 7 8 5 7 4 7 0 4 8 58 58 58 58 5 RF Freq = 0.45 GHz @ 0 dBm LO Freq = 0.38 GHz @ +17 dBm All values in dBc relative to the IF output power. Harmonics of LO nLO Spur @ RF Port LO Freq (GHz) 1 2 3 4 0.35 27 37 38 39 0.37 26 35 43 39 0.39 25 34 44 41 0.41 24 33 41 43 0.43 23 32 38 44 0.45 22 31 37 45 LO = +17 dBm All values are in dBc below input LO level @ RF port. +25 C +85 C -40 C INPUT IP2 (dBm) RF FREQUENCY (GHz) LO= +13dBm LO= +15dBm LO= +17dBm LO= +19dBm INPUT IP2 (dBm) RF FREQUENCY (GHz) Input P1dB vs. Temperature IF = 70 MHz +25 C +85 C -40 C INPUT P1dB (dBm) RF FREQUENCY (GHz) HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz v02.0705 HMC387MS8 / 387MS8E

For price, delivery, and to place orders, please contact Hittite Microwave Corporation: Order On-line at www.hittite.com Absolute Maximum Ratings RF/IF Input +25 dBm LO Drive +27 dBm Channel Temperature (Tc) 150 °C Thermal Resistance 175 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C IF DC Current ±40 mA ESD Sensitivity (HBM) Class 1A Outline Drawing ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. Part Number Package Body Material Lead Finish MSL Rating Package Marking [3] HMC387MS8 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] H387 XXXX HMC387MS8E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] H387 XXXX [1] Max peak refl ow temperature of 235 °C [2] Max peak refl ow temperature of 260 °C [3] 4-Digit lot number XXXX

Package Information

MIXER, 450 - 500 MHz v02.0705 HMC387MS8 / 387MS8E

For price, delivery, and to place orders, please contact Hittite Microwave Corporation: Order On-line at www.hittite.com Pin Descriptions Pin Number Function Description Interface Schematic 1L O This pin is AC coupled & matched to 50 Ohms when an external series inductor (L1) and shunt capacitor (C1) is connected to the LO. Choose values of L1 and C1 to optimize LO frequency response. See Application Circuit herein. 2, 4 N/C Not connected. 3, 6, 7 GND This pin must be connected to RF ground. 5I F This pin is DC coupled. For applications not requiring operation to DC this port should be DC blocked externally using a series capacitor. Choose value of C1 to pass IF frequency desired. For operation to DC, this pin must not sink/source more than 40 mA of current or failure may result. 8R F This pin is DC coupled & matched to 50 Ohms from 450 - 500 MHz HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz v02.0705 HMC387MS8 / 387MS8E

For price, delivery, and to place orders, please contact Hittite Microwave Corporation: Order On-line at www.hittite.com Evaluation PCB Item Description J1 - J3 PCB Mount SMA RF Connector C1 4 pF Chip Capacitor, 0603 Pkg L1 47 nH Chip Inductor, 0805 Pkg U1 HMC387MS8 / HMC387MS8E Mixer PCB [2] 106307 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 [3] Unless otherwise noted, all measurements performed as a downconverter with low side LO & IF = 200 MHz [4] LO Frequency optimized. See application circuit herein. The circuit board used in the fi nal application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. List of Materials for Evaluation PCB 107334 [1] HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz v02.0705 HMC387MS8 / 387MS8E

For price, delivery, and to place orders, please contact Hittite Microwave Corporation: Order On-line at www.hittite.com LO Frequency (MHz) L1 (nH) C1 (pF) 400 47 4 Selection of L1 & C1 for Optimal LO Frequency ±10% Application Circuit Choose value of L1 & C1 to optimize LO Frequency response. For best results use an 0805 size RF inductor or smaller. Note: Position L1 and C1 as close to Pin 1 as possible. HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz v02.0705 HMC387MS8 / 387MS8E