33250A

33250A KEYSIGHT | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Product Discontinuance Notice The 33250A function generator and all associated options will be discontinued December 1, 2016. The last date this product can be ordered is November 30, 2016. – For new product purchases, Keysight recommends the 33600A Trueform Series waveform generators. – For more information, as well as to access to detailed migration guides, please visit www.keysight.com/find/nextgenFGs – To contact a product selection expert, visit www.keysight.com/find/contactus Keysight 33250A Function/Arbitrary Waveform Generator Data Sheet

02 | Keysight | 33250A Function/Arbitrary Waveform Generator - Data Sheet Standard Waveforms The Keysight Technologies, Inc. 33250A function/arbitrary waveform generator uses direct digital-synthesis techniques to create a stable, accurate output on all waveforms, down to 1 µHz frequency resolution. The benefits are apparent in every signal you produce, from the sine wave frequency accuracy to the fast rise/fall times of square waves, to the ramp linearity. Front-panel operation of the 33250A is straightforward and user friendly. The knob or numeric keypad can be used to adjust frequency, amplitude and offset. You can even enter voltage values directly in Vpp, Vrms, dBm, or high/low levels. Timing parameters can be entered in hertz (Hz) or seconds. Custom Waveform Generation Why settle for a basic function generator when you can get arbitrary waveforms at no extra cost? With the 33250A, you can generate arbitrary waveforms with 12-bit vertical resolution, 64K memory depth, and a sample rate of 200 MSa/s. You can also store up to four 64K-deep arbitrary waveforms in non-volatile memory with user-defined names to help you find the right waveform when you need it most. The included Keysight IntuiLink software allows you to easily create, edit, and download complex waveforms using the IntuiLink arbitrary waveform editor. Or you can capture a waveform using IntuiLink oscilloscope or DMM and send it to the 33250A for output. For programmers, ActiveX components can be used to control the instrument using SCPI commands. IntuiLink provides the tools to easily create, download, and manage waveforms for your 33250A. To find out more about IntuiLink, visit www.keysight.com/find/intuilink . Pulse Generation The 33250A can generate simple pulses up to 50 MHz. With variable edge time, pulse width and voltage level, the 33250A is ideally suited to a wide variety of pulse applications. Built-in Versatility AM, FM and FSK capabilities make it easy to modulate waveforms with or without a separate source. Linear or logarithmic sweeps can be performed with a programmable frequency marker signal. Programmable burst count and gating allow you to further customize your signal. For system applications, both GPIB and RS-232 interfaces are standard, and support full programmability using SCPI commands. – 80 MHz sine and square wave outputs – Sine, square, ramp, noise and other waveforms – 50 MHz pulse waveforms with variable rise/fall times – 12-bit, 200 MSa/s, 64K-point deep arbitrary waveform Color Graphical Display The unique design of the 33250A combines a low-profile instrument with the benefits of a color graphical display. Now you can display multiple waveform parameters at the same time. The graphical interface also allows you to modify arbitrary wave - forms quickly and easily. Timebase Stability and Clock Reference The 33250A TCXO timebase gives you frequency accuracy of 2 ppm for your most demanding applications. The external clock reference input/output lets you synchronize to an external

10 MHz clock, to another 33250A, or

to another Keysight 332XXA function/ arbitrary wafeform generator. Phase adjustments can be made from the front panel or via a computer interface, allowing precise phase calibration and adjustment.

03 | Keysight | 33250A Function/Arbitrary Waveform Generator - Data Sheet Measurement Characteristics Waveforms Standard Sine, square, pulse, ramp, noise, sin(x)/x, exponential rise, exponential fall, cardiac, DC volts Arbitrary Waveform length 1 to 64K points Amplitude resolution 12 bits (including sign) Repetition rate 1 µHz to 25 MHz Sample rate 200 MSa/s Filter bandwidth 50 MHz Non-vol. memory Four (4) 64K waveforms Frequency characteristics Sine 1 µHz to 80 MHz Square 1 µHz to 80 MHz Pulse 500 µHz to 50 MHz Arb 1 µHz to 25 MHz Ramp 1 µHz to 1 MHz White noise 50 MHz bandwidth Resolution 1 µHz; except pulse, 5 digits Accuracy (1 year) 2 ppm, 18 to 28 °C 3 ppm, 0 to 55 °C Sinewave spectral purity Harmonic distortion DC to 1 MHz 1 to 5 MHz 5 to 80 MHz ≤ 3 Vpp1 > 3 Vpp –60 dBc –55 dBc –57 dBc –45 dBc –37 dBc2 –30 dBc2 Total harmonic distortion DC to 20 kHz < 0.2% + 0.1 mVrms Spurious (non-harmonic) 3 DC to 1 MHz –60 dBc 1 to 20 MHz –50 dBc 20 to 80 MHz –50 dBc + 6 dBc/octave Phase noise (30 kHz band)

10 MHz < –65 dBc (typical)

80 MHz < –47 dBc (typical)

Rise/fall time < 8 ns4 Overshoot < 5% Asymmetry 1% of period + 1 ns Jitter (rms) < 2 MHz ≥ 2 MHz 0.01% + 525 ps 0.1% + 75 ps Duty cycle ≤ 25 MHz 25 to 50 MHz 50 to 80 MHz 20.0 to 80.0% 40.0 to 60.0% 50.0% (fixed) Pulse Period 20.00 ns to 2000.0 s Pulse width 8.0 ns to 1999.9 s Variable edge time 5.00 ns to 1.00 ms Overshoot < 5% Jitter (rms) 100 ppm + 50 ps Signal characteristics (Continued) Ramp Linearity < 0.1% of peak output Symmetry 0.0 to 100.0% Arb Minimum edge time < 10 ns Linearity < 0.1% of peak output Settling time < 50 ns to 0.5% of final value Jitter (rms) 30 ppm + 2.5 ns Output characteristics Amplitude (into 50 Ω) 10 mVpp to 10 Vpp5 Accuracy (at 1 kHz, >10 mVpp, Autorange on) ± 1% of setting ± 1 mVpp Flatness (sinewave relative to 1 kHz, Autorange on) < 10 MHz 10 to 50 MHz 50 to 80 MHz ± 1% (0.1 dB)6 ± 2% (0.2 dB) ± 5% (0.4 dB) Units Vpp, Vrms, dBm, high and low level Resolution 0.1 mV or 4 digits Offset (into 50 Ω) ± 5 Vpk ac + dc Accuracy 1% of setting + 2 mV + 0.5% of amplitude Waveform output Impedance 50 Ω typical (fixed) > 10 MΩ (output disabled) Isolation 42 Vpk maximum to earth Protection Short-circuit protected 7; overload relay automatically disables main output Modulation characteristics AM Carrier waveforms Sine, square, ramp, and arb Mod. waveforms Sine, square, ramp, noise, and arb Mod. frequency 2 mHz to 20 kHz Depth 0.0 to 120.0% Source Internal/external FM Carrier waveforms Sine, square, ramp, and arb Mod. waveforms Sine, square, ramp, noise, and arb Mod. frequency 2 mHz to 20 kHz Peak deviation DC to 80 MHz Source Internal/external FSK Carrier waveforms Sine, square, ramp, and arb Mod. waveform 50% duty cycle square Internal rate 2 mHz to 100 kHz Frequency range 1 µHz to 80 MHz Source Internal/external External modulation input Voltage range ± 5 V full scale Input impedance 10 Ω Frequency DC to 20 kHz Latency < 70 µs typical

04 | Keysight | 33250A Function/Arbitrary Waveform Generator - Data Sheet Burst Waveforms Sine, square, ramp, pulse, arb, and noise Frequency 1 µHz to 80 MHz8 Burst count 1 to 1,000,000 cycles or infinite Start/Stop phase -360.0 to +360.0° Internal period 1 ms to 500 s Gate source External trigger Trigger source Single manual trigger, Trigger delay N-cycle, infinite 0.0 ns to 85.000 sec Sweep Waveforms Sine, square, ramp, and arb Type Linear and logarithmic Direction Up or down Start F/Stop F 100 µHz to 80 MHz Sweep time 1 ms to 500 s Trigger Single manual trigger, internal, external trig Marker Falling edge of sync signal (programmable) System characteristics Configuration times (typical) 9 Function change Standard Pulse Built-in arb 100 ms 660 ms 220 ms Frequency change 20 ms Amplitude change 50 ms Offset change 50 ms Select user arb < 900 ms for < 16K pts. Modulation change < 200 ms Arb download times GPIB/RS-232 (115Kbps) Arb Length Binary 64K points 48 sec 16K points 12 sec 8K points 6 sec 4K points 3 sec 2K points 1.5 sec ASCII Integer ASCII Real 112 sec 186 sec 28 sec 44 sec 14 sec 22 sec 7 sec 11 sec 3.5 sec 5.5 sec Trigger characteristics Trigger input Input level TTL compatible Slope Rising or falling, (selectable) Pulse width > 100 ns Input impedance 10 kΩ, DC coupled Latency Burst Sweep < 100 ns (typical) < 10 µs (typical) Jitter (rms) Burst Sweep 1 ns; except pulse, 300 ps 2.5 µs 1. Harmonic distortion at low amplitudes is limited by a –70 dBm floor 2. Harmonic distortion at 40 MHz only is –33 dBc 3. Spurious noise at low amplitudes is limited by a –75 dBm floor 4. Edge time decreased at higher frequency, 3.5 nS (typical) 5. 20 mVpp to 20 Vpp into open-circuit load 6. dB rounded to 1 digit, instrument adheres to “%” specification 7. Short-circuit protected to ground at all times 8. Sine and square waveforms above 25 MHz only with infinite burst count 9. Time to change parameter and output new signal Measurement Characteristics (Continued) Trigger output Level TTL compatible into 50 Ω Pulse width > 450 ns Maximum rate 1 MHz Fanout ≤ 4 Keysight 33250A’s (or equivalent) Clock Reference Phase Offset Range –360 to +360° Resolution 0.001° External reference input Lock range 10 MHz ± 35 kHz Level 100 mVpp to 5 Vpp Impedance 1 kΩ nominal, accoupled Lock time < 2 s Internal reference output Frequency 10 MHz Level 632 mVpp (0 dbm), nominal Impedance 50 Ω nominal, accoupled Sync output Level TTL compatible into > 1 kΩ Impedance 50 Ω nominal General Power supply 100-240 V, 50-60 Hz 100-127 V, 50-400 Hz Power consumption 140 VA Operating temp. 0 to 55°C Storage temp. –30 to 70°C Stored states 4 named user configurations Power on state Default or last Interface IEEE-488 and RS-232 std. Language SCPI-1997, IEEE-488.2 Dimensions (WxHxD) Bench top Rackmount 254 x 104 x 374 mm 213 x 89 x 348 mm Weight 4.6 kg Safety designed to EN61010-1, CSA1010.1, UL-311-1 EMC tested to IEC-61326-1 IEC-61000-4-3 criteria B IEC-61000-4-6 criteria B Vibration and shock MIL-T-28800E, Type III, Class 5 Acoustic noise 40 dBA Warm-up time 1 hour Calibration interval 1 year

For more information on Keysight Technologies’ products, applications or services, please contact your local Keysight office. The complete list is available at: www.keysight.com/find/contactus Americas Canada (877) 894 4414 Brazil 55 11 3351 7010 Mexico 001 800 254 2440 United States (800) 829 4444 Asia Pacific Australia 1 800 629 485 China 800 810 0189 Hong Kong 800 938 693 India 1 800 112 929 Japan 0120 (421) 345 Korea 080 769 0800 Malaysia 1 800 888 848 Singapore 1 800 375 8100 Taiwan 0800 047 866 Other AP Countries (65) 6375 8100 Europe & Middle East Austria 0800 001122 Belgium 0800 58580 Finland 0800 523252 France 0805 980333 Germany 0800 6270999 Ireland 1800 832700 Israel 1 809 343051 Italy 800 599100 Luxembourg +32 800 58580 Netherlands 0800 0233200 Russia 8800 5009286 Spain 800 000154 Sweden 0200 882255 Switzerland 0800 805353 Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT) United Kingdom 0800 0260637 For other unlisted countries: www.keysight.com/find/contactus (BP-09-23-14) 05 | Keysight | 33250A Function/Arbitrary Waveform Generator - Data Sheet This information is subject to change without notice. © Keysight Technologies, 2011-2015 Published in USA, May 21, 2015 5968-8807EN www.keysight.com www.keysight.com/find/33250A

Ordering Information

80 MHz function/arbitrary wavefrom generator

Operating manual, service manual, quick reference guide, IntuiLink waveform editor software, test data, RS-232 cable, and power cord (see language option). Options Opt. A6J ANSI Z540 calibration Opt. AB0 Taiwan: Chinese manual Opt. AB1 Korea: Korean manual Opt. AB2 China: Chinese manual Opt. ABA English: English manual Opt. ABD Germany: German manual Opt. ABF France: French manual Opt. ABJ Japan: Japanese manual Other Accessories 34131A Carrying case 34161A Accessory pouch 34190A Rackmount kit* * For racking two 33250As side-by-side, order the following items: Lock-link kit (34194A), Flange kit (34191A)