1P00S6W33B0CA0Z1 ELITE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

Elite Enterprises (H.K.) Co., Ltd E l i t e E n t e r p r i s e s ( H . K . ) C o . , L t d Part No.: 1P00S6W33B0CA0Z1 F l a t 1 6 0 3 A , 1 6 / F . , N a n y a n g P l a z a , 5 7 H u n g T o R o a d , K w u n T o n g , H . K . V e r 1 . 0 Tel: (852) 2723-3122 Fax: (852) 2723-3990 Email: info@elite-ent.com.hk Part No.﹕1P00S6W33B0CA0Z1 § Standard 7.62*7.62*3.5mm diameter package. ITEM MATERIALS Resin(Mold) Epoxy P a g e : 1 / 8 C Water Transparent T Colored Transparent Lens Color Code White Diffused M Colored Diffused D Lead Frame Ag Plating Copper Alloy Dice InGaN Absolute Maximum Ratings（Ta=25℃） Item Symbol Value Unit Power Dissipation 120 mW PD DC Forward Current 35 mA IF 100* Pulsed Forward Current mA IFP Reverse Voltage 5 V VR Operating Temperature -30 ~ +80▲ ℃ Topr Storage Temperature -40 ~ +100 ℃ Tstg Soldering Temperature 260for5sec△ ℃ Tsol * Duty 1/10 Pulse Width 0.1ms △ At the position of 4mm from the bottom Directive Characteristics（Ta=25℃） of the package ▲Please refer to the Curve of Forward Current vs. Temperature.

Elite Enterprises (H.K.) Co., Ltd E l i t e E n t e r p r i s e s ( H . K . ) C o . , L t d Part No.: 1P00S6W33B0CA0Z1 F l a t 1 6 0 3 A , 1 6 / F . , N a n y a n g P l a z a , 5 7 H u n g T o R o a d , K w u n T o n g , H . K . V e r 1 . 0 Tel: (852) 2723-3122 Fax: (852) 2723-3990 Email: info@elite-ent.com.hk Electrical-Optical Characteristics（Ta=25℃） P a g e : 2 / 8 Value Parameter Symbol Unit Test condition Min. Typ. Max. Forward Voltage Vf V If=30mA 3.0 3.3 4.0 Luminous intensity Iv mcd If=30mA ﹍ 600 1150 LM Luminous Flux ﹍ 1250 2550 mlm If=30mA X If=30mA ﹍ ﹍ 0.295 Wavelength ﹍ ﹍ y If=30mA 0.303 Reverse Current μA ﹍ ﹍ Ir Vr=5V 10 Viewing angle 2θ1/2 ﹍ ﹍ If=30mA 130 Deg Luminous intensity (IV) ±10%, (Forward Voltage )VF ±0.1V, (Wavelength)λd ±0.01 Range of bins Rank(Bin 碼) 10* 11* 12* 9 13 Luminous 1630-2120 2120-2760 2760-3590 1250-1630 2760-3590 Intensity(mlm) Rank(Bin 碼) λd * Bin codes in bold are the main bins

Elite Enterprises (H.K.) Co., Ltd E l i t e E n t e r p r i s e s ( H . K . ) C o . , L t d Part No.: 1P00S6W33B0CA0Z1 F l a t 1 6 0 3 A , 1 6 / F . , N a n y a n g P l a z a , 5 7 H u n g T o R o a d , K w u n T o n g , H . K . V e r 1 . 0 Tel: (852) 2723-3122 Fax: (852) 2723-3990 Email: info@elite-ent.com.hk 白光正常分 BIN 圖 P a g e : 3 / 8 chromaticity chromaticity chromaticity Rank Rank Rank x y x y x y C T G D U J 0.3016 0.3043 0.2716 0.2426 E V L 0.2976 0.3222 0.2670 0.2482 0.2959 0.2893 0.2976 0.3222 0.3056 0.299 0.3016 0.3043 0.3300 0.3348 F W 0.3300 0.3600 0. 2 0.23 0.24 0.25 0.26 0.27 0.28 0.29 0.30 0.31 0.32 0.33 0.34 0.35 0. 21 0. 22 0. 23 0. 24 0. 25 0. 26 0. 27 0. 28 0. 29 0. 30 0. 31 0. 32 0. 33 0. 34 0. 35 0. 36 C J L T D U E V F G W

Elite Enterprises (H.K.) Co., Ltd E l i t e E n t e r p r i s e s ( H . K . ) C o . , L t d Part No.: 1P00S6W33B0CA0Z1 F l a t 1 6 0 3 A , 1 6 / F . , N a n y a n g P l a z a , 5 7 H u n g T o R o a d , K w u n T o n g , H . K . V e r 1 . 0 Tel: (852) 2723-3122 Fax: (852) 2723-3990 Email: info@elite-ent.com.hk Electrical characteristic graph P a g e : 4 / 8

Elite Enterprises (H.K.) Co., Ltd E l i t e E n t e r p r i s e s ( H . K . ) C o . , L t d Part No.: 1P00S6W33B0CA0Z1 F l a t 1 6 0 3 A , 1 6 / F . , N a n y a n g P l a z a , 5 7 H u n g T o R o a d , K w u n T o n g , H . K . V e r 1 . 0 Tel: (852) 2723-3122 Fax: (852) 2723-3990 Email: info@elite-ent.com.hk Outline Dimensions P a g e : 5 / 8 § All dimensions are in millimeters. § Tolerance is ±0.25 ㎜ unless otherwise noted. § NOTE 3 Protruded resin under flange is 1.0 ㎜ max.

Elite Enterprises (H.K.) Co., Ltd E l i t e E n t e r p r i s e s ( H . K . ) C o . , L t d Part No.: 1P00S6W33B0CA0Z1 F l a t 1 6 0 3 A , 1 6 / F . , N a n y a n g P l a z a , 5 7 H u n g T o R o a d , K w u n T o n g , H . K . V e r 1 . 0 Tel: (852) 2723-3122 Fax: (852) 2723-3990 Email: info@elite-ent.com.hk P a g e : 6 / 8 LED Usage and Handling Instructions Dear valued clients: Thank you for choose our LED produ cts. LEDs are delicate semiconductor product that should be handle according to the below instructions. A. Storage: 1. LEDs should be stored in an environment with ambient temperature of 23 ± 5 ℃ and relative humidity of 40 ~ 70 %. 2. LEDs should be used within three months of being taken out of their original packages to avoid lead frame rusting. B. Cleaning: 1. Do not use any unidentified chemical to clean LEDs, it could damage or crack the LED epoxy surface. If necessary, soak LED in alcohol for a time not exceeding one minute in normal temperature. C. Lead Frames Shaping & Trimming 1. The shaping should be done underneath the wedge point. No pressure should be exerted to the epoxy shell of the LED during shaping. 2. Bending of the leads should be done at a point at least 4 mm from the base of the LED lens. 3. Shaping of the leads should be done before soldering. 4. Lead trimming should only be done at normal temperature. D. Soldering 1. When soldering, the soldering iron needs to be at least 2mm away from the epoxy edge. After soldering, allow at least 3 minutes for LEDs to cool back to normal temperature. Do not apply any pressure to the epoxy encapsulation or the lead frame during the soldering process. 2. When reflow soldering or wave soldering, please solder once for less than 5 seconds at a maximum temperature of 260°C. During the soldering process, if the temperature or timing is not controlled within limits, it would cause the epoxy to deform or cause the die or wires within the LED to be damaged. 3. When using soldering iron, please solder once for less than 5 seconds at a maximum temperature of 300°C. When soldering a row of LED on a PCB, please do not solder both leads of a LED in sequence. (Solder all the positive lead first, then all the negative leads)

Elite Enterprises (H.K.) Co., Ltd E l i t e E n t e r p r i s e s ( H . K . ) C o . , L t d Part No.: 1P00S6W33B0CA0Z1 F l a t 1 6 0 3 A , 1 6 / F . , N a n y a n g P l a z a , 5 7 H u n g T o R o a d , K w u n T o n g , H . K . V e r 1 . 0 Tel: (852) 2723-3122 Fax: (852) 2723-3990 Email: info@elite-ent.com.hk P a g e : 7 / 8 4. Do not dip the epoxy encapsulation part of LED into any soldering paste liquid. 5. After soldering, do not adjust the location of the LED anymore. 6. When attaching electronic parts to a PCB with LEDs, the curing time for the whole PCB should be less than 60 seconds, at less than a temperature of 120 °C. E. Installation 1. During the installation process, do not apply any pressure to the leads. 2. Please make sure the installation holes on the PCB matches the leads of the LED. F. ESD (Electrostatic Discharge) 1. LED is very sensitive to ESD; please make sure during the whole usage and installation process, that no ESD exist to affect the LED. Excessive ESD could damage the LED chip and result in performance degradation. 2. LED can also be damaged by electrical surge, please make sure any driving electrical circuits are equipped with surge protection. 3. During the installation process, please make sure all the equipment and personnel are grounded properly. Make use ESD protection equipment such as anti-static gloves, anti-static wrist bands, anti-static mats, anti-static clothes, anti-static shoes, and anti-static containers. 4. When LED come into contact with low electrical resistance metallic surfaces, the ESD could damage the LED due to sudden discharge of ESD. Please make sure all surfaces that will be in contact with LED are covered with anti-static mats (Surface electrical resistance of 106~~108Ω/sq). LED should be placed in anti-static containers and anti-static bags. 5. All soldering irons should be grounded and production environment should make use of ion-blowers. 6. The diameter of the dip holes on PCB should be at least 0.8mm . The distance between the centers of the two dip holes should be within ± 0.02mm of the LED lead pitch (standard LED lead pitch is 2.54mm ). For special LED lead pitch specifications, the distance should be adjusted accordingly.

Elite Enterprises (H.K.) Co., Ltd E l i t e E n t e r p r i s e s ( H . K . ) C o . , L t d Part No.: 1P00S6W33B0CA0Z1 F l a t 1 6 0 3 A , 1 6 / F . , N a n y a n g P l a z a , 5 7 H u n g T o R o a d , K w u n T o n g , H . K . V e r 1 . 0 Tel: (852) 2723-3122 Fax: (852) 2723-3990 Email: info@elite-ent.com.hk G. Recommended Usage Guidelines 1. Please only use 20mA (Lamp LED) and 30mA (High Flux LED) of forward current to drive LEDs whether one LED or multiple LEDs are being used. 2. Circuit connections i. Serial connection ii. Parallel connection P a g e : 8 / 8 3. Sudden surge could damage the LED interior connections. Please design circuit with care so no sudden voltage surge or current surge will show when turning the circuit on or off. 4. When color or brightness uniformity is required while using multiple LEDs, the LED driver condition is critical. Our company guarantees the uniformity of the LEDs from the same bin when the driver current is 20mA (Lamp LED) and 30mA (High Flux LED) H. Safety 1. Please comply with government electrical safety code while using the LEDs. 2. Do not look directly into a lit LED; it could damage the eyes after only a few seconds. 3. Do not look directly into powered UV LEDs; it could damage the eyes after only a few seconds. (UV LEDs are mainly used in currency validating machines)