1688382 PHOENIX | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

https://www.phoenixcontact.com/pi/products/1688382 09/11/2020 Page 1 / 7 Contact insert - VS-09-ST-DSUB-ER - 1688382 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) D-SUB contact insert, shell size 1, with 9 signal contacts, type of contact pin, for PCB mounting, angled, fixing with M3 thread and solder pins, for panel mounting frame VS-09-... Key Commercial Data Packing unit 10 pc GTIN GTIN 4017918818333 Technical data Mechanical characteristics Connection method Solder connection Overvoltage category III Degree of pollution 2 Weight 11.49 g Flammability rating according to UL 94 V0 Ambient conditions Ambient temperature (operation) -55 °C ... 125 °C Material data Contact surface material Hard gold-plated over nickel Contact material Copper alloy Contact carrier material PBT-GF Housing material Steel, tin-plated Width 21.5 mm Height 17.8 mm Length 31.19 mm Mounting type Threads and solder pins

https://www.phoenixcontact.com/pi/products/1688382 09/11/2020 Page 2 / 7 Contact insert - VS-09-ST-DSUB-ER - 1688382 Technical data

Electrical characteristics

Rated current 5 A (at 20 °C) Overvoltage category III Degree of pollution 2 Rated voltage (III/3) 125 V Test voltage 1200 V Standards and Regulations Flammability rating according to UL 94 V0 Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.

  • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
  • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
  • The products are suitable for applications in plant, controller, and electrical device engineering.
  • When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
  • Assembled products may not be manipulated or improperly opened.
  • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
  • When using the product in direct connection with third-party manufacturers, the user is responsible.
  • For operating voltages > 50 V AC, conductive connector housings must be grounded
  • Only use tools recommended by Phoenix Contact
  • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
  • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
  • Operate the connector only when it is fully plugged in and interlocked.
  • Operate the connector only when it is fully plugged in.
  • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
  • Observe the minimum bending radius of the cable. Lay the cable without twisting it. applicable when combining several circuits in a cable and/or connector

https://www.phoenixcontact.com/pi/products/1688382 09/11/2020 Page 3 / 7 Contact insert - VS-09-ST-DSUB-ER - 1688382 Technical data Environmental Product Compliance REACh SVHC Lead 7439-92-1 China RoHS Environmentally Friendly Use Period = 50 years For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration” Drawings Dimensional drawing D-SUB contact insert

https://www.phoenixcontact.com/pi/products/1688382 09/11/2020 Page 4 / 7 Contact insert - VS-09-ST-DSUB-ER - 1688382 Drilling diagram Drilling diagram

https://www.phoenixcontact.com/pi/products/1688382 09/11/2020 Page 5 / 7 Contact insert - VS-09-ST-DSUB-ER - 1688382 Schematic diagram Classifications eCl@ss eCl@ss 10.0.1 27440205 eCl@ss 4.0 27260700 eCl@ss 4.1 27260700 eCl@ss 5.0 27260700 eCl@ss 5.1 27261200 eCl@ss 6.0 27261200 eCl@ss 7.0 27440205 eCl@ss 8.0 27440205 eCl@ss 9.0 27440205 ETIM ETIM 2.0 EC000437 ETIM 3.0 EC000437

https://www.phoenixcontact.com/pi/products/1688382 09/11/2020 Page 6 / 7 Contact insert - VS-09-ST-DSUB-ER - 1688382 Classifications ETIM ETIM 4.0 EC000437 ETIM 5.0 EC000438 ETIM 6.0 EC000438 ETIM 7.0 EC000438 UNSPSC UNSPSC 6.01 31261501 UNSPSC 7.0901 31261501 UNSPSC 11 31261501 UNSPSC 12.01 31261501 UNSPSC 13.2 39121522 UNSPSC 18.0 39121522 UNSPSC 19.0 39121522 UNSPSC 20.0 39121522 UNSPSC 21.0 39121522 Approvals Approvals Approvals UL Recognized / EAC Ex Approvals Approval details UL Recognized http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm FILE E 118976 EAC B.01687

https://www.phoenixcontact.com/pi/products/1688382 09/11/2020 Page 7 / 7 Phoenix Contact 2020 © - all rights reserved http://www.phoenixcontact.com PHOENIX CONTACT GmbH & Co. KG Flachsmarktstr. 8

32825 Blomberg

Tel. +49 5235 300 Fax +49 5235 3 41200 http://www.phoenixcontact.com