020-3105-XX

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

P7600 Series TriMode™ Probes P7633 Low Noise TriMode Probe The P7600 Series TriMode probes and the MSO/DPO70000DX and DPO/ DSA70000D Series Oscilloscopes are designed to deliver the industry's lowest system noise levels. This high sensitivity is critical for being able to make accurate measurements on low amplitude signals. Key performance specs Full 33 GHz bandwidth to the probe tip (P7633) Industry's lowest probe and oscilloscope system noise Key features TriMode™ probe - one setup, three measurements without adjusting probe tip connections Differential Single ended Common mode Remote head design connectivity Allows placement of probe amplifier close to the circuit being measured Coaxial adapters 2.92mm SMP P7500 probe tip adapter Use P7500 Series TriMode solder-in probe tips Probe automatically detects tips and applies DSP correction filters Probe-specific S-parameters Unique DSP filters created from data stored in the probe TekConnect® Interface - TekConnect scope/probe control and usability Direct control from probe compensation box or from scope menu

Applications

Including, but not limited to: MIPI M-PHY, PCI Express, Serial ATA, Serial Attached SCSI, Fibre Channel, and HDMI Combining TriMode probing with low noise performance TriMode probing enhances productivity by enabling differential, single- ended, and common mode measurements with a single probe setup. Connecting a probe to the device under test can be a time consuming activity, especially if the probe has to be set up differently to make all the necessary measurements. TriMode probing improves productivity by reducing setup time, because only one setup is needed to make the three different types of measurements. Switching between Differential Mode [A- B], Single-Ended Mode [A-Gnd, B-Gnd], and Common Mode [((A+B)/2)- Gnd] is as easy as a press of a button. Changing input modes on the probe is as easy as a press of a button As high speed serial data standards increase in speed and signal swings shrink, probes with high bandwidth coupled with low noise and high sensitivity are increasingly important for making accurate measurements.

12 Gb/s 200 mVpp signal measured with a P7633 and a P76CA-292C coaxial adapter

www.tek.com 1

The MSO/DPO70000DX and DPO70000SX Series oscilloscopes and the P7600 Series TriMode probes were designed to deliver the industry's lowest system noise levels. When used with a P76CA-xxx Coaxial Adapters, the vertical setting on the oscilloscope can be set as low as 3.48 mV/div with a system noise <1.1 mVrms at 33 GHz bandwidth. This high sensitivity is critical for being able to make accurate measurements on low amplitude signals. The P7600 Series TriMode probes were designed to deliver superior sensitivity and allow the oscilloscope to directly measure small signals without using a zoom function. Using a zoom function to look at small signals does not change the intrinsic noise floor of the instrument which can make measurements on small signals problematic. Connectivity The P7600 Series probes utilize an interchangeable active tip design built around a custom tip interface using high frequency SMPM connectors. The P7600 Series probes feature an Automatic Adapter ID function that recognizes the attached adapter and automatically applies the correct DSP filters that eliminate imperfections in the frequency response all the way to the probe tip. This feature eliminates the risk of manually selecting the wrong tip type and is more efficient for the user. Coaxial adapters Coaxial adapters enable the probe to act like a differential input channel for the oscilloscope which effectively doubles the number of differential signals a single oscilloscope can measure simultaneously. P76CA-292 33 GHz Bandwidth Coaxial Adapter with 2.92 mm (Female) connectors. This adapter is calibrated at the input connectors and is ideal for use with off the shelf or custom cables. Low skew cable pairs should be used to preserve full bandwidth performance. P76CA-292C 33 GHz Bandwidth Coaxial Adapter with 2.92 mm (Male) connectors and 6" of high performance cable. This adapter is calibrated at the input connectors and is ideal for directly connecting to devices with 2.92 mm or SMA output connectors. P76CA-SMP Datasheet 2 www.tek.com

33 GHz Bandwidth Coaxial Adapter with SMP (Female) connectors and 6"

of high performance cable. This adapter is calibrated at the input connectors and is ideal for directly connecting to devices with SMP output connectors. P7500 Series solder tip adapter This adapter allows the P7630 probe to use existing Tektronix P7500 probe tips. The P7600 Series probe amplifiers have a 50 Ω input. When combined with a P7500 probe tip, the probe turns into a passive Z0 style probe with 450 Ω of differential input impedance. While Z0 probes can typically present a significant DC load to the device under test, the P7600 Series probes will minimize the effect of DC loading through the use of termination voltage adjustment. P76TA 30 GHz Bandwidth P7500 Tip Adapter. The probe and oscilloscope system will support up to 30 GHz of bandwidth when this adapter is used with the P75PST Performance Solder Tip. Unique probe filters The P7600 Series probes contain probe specific S-parameter data. Attaching a P7600 probe to a MSO/DPO70000DX or DPO70000SX oscilloscope transfers this data to the instrument to create unique system DSP filters based on the specific S-parameter data of the oscilloscope and the probe. Creating unique filters based on the specific response of the system is critical as bandwidths increase. At bandwidths of 33 GHz, small variations in the signal path can lead to significant variation in frequency response. These variations are corrected using DSP filtering. P7600 Series TriMode Probes www.tek.com 3

Adapter P76CA-xxx P76TA P76CA-xxx P76TA Characteristic Bandwidth 33 GHz 30 GHz 25 GHz 25 GHz Rise time (10-90%) 14 ps 16 ps 18 ps 18 ps Rise time (20-80%) 11 ps 12 ps 14 ps 14 ps Typical Characteristics Attenuation P76CA-xxx 0.25X / 0.5X / 1X / 2X / 4X P76TA 1.25X / 2.5X / 5X / 10X / 20X Input voltage range P76CA-xxx 1.2 Vpp single-ended, 2.0 Vpp differential P76TA 6.0 Vpp single-ended, 10.0 Vpp differential Operating voltage window P76CA-xxx -4 V to +4 V P76TA -5 V to +5 V Offset voltage range -4 V to +4 V Termination voltage range -4 V to +4 V DC input resistance P76CA-xxx 50 Ω ±2 Ω P76TA 225 Ω Input return loss P76CA-xxx >20 dB to 5 GHz >12 dB 5 GHz to 20 GHz >10 dB 20 GHz to 30 GHz >8 dB 30 GHz to 33 GHz P76TA NA Z min P76CA-xxx NA P76TA 225 Ω at 1 GHz, 150 Ω at 10 GHz, 100 Ω at 25 GHz Noise, referred to input (System noise with oscilloscope set in minimum V/div setting) <1.1 mVrms (33 GHz) <0.9 mVrms (25 GHz) Datasheet 4 www.tek.com

CMRR (differential mode) P76CA-xxx >40 dB at DC >14 dB DC to 15 GHz >6 dB 15 GHz to 30 GHz >4 dB 30 GHz to 33 GHz P76TA NA Nondestructive input voltage range P76CA-xxx -5 V to +5 V (DC + peak AC) P76TA -8 V to +8 V (DC + peak AC) Interface TekConnect Minimum system requirements Instrument Bandwidth Firmware version Recommended probe MSO/DPO73304DX, DPO73304SX, and DPO/ DSA73304D 33 GHz V6.8 and above P7633 MSO/DPO72504DX, DPO73304SX, and DPO/ DSA72504D 25 GHz V6.8 and above P7625 Environmental characteristics Temperature Operating 0 to +40 °C (+32 °F to +104 °F) Nonoperating -20 °C to +71 °C (-4 °F to +160 °F) Humidity Operating Up to +40 °C (+104 °F) 20%-80% RH Nonoperating +30 °C to +46 °C (+86 °F to +115 °F) 0-90% RH Altitude Operating 3000 meters (9842 feet) Nonoperating 12000 meters (39,370 feet) P7600 Series TriMode Probes Typical Characteristics www.tek.com 5

Ordering information

P7633 Low Noise TriMode™ Probe, 33 GHz, TekConnect Interface P7625 Low Noise TriMode™ Probe, 25 GHz, TekConnect Interface NOTE: All P7600 Series probes require a P76CA-SMP, P76CA-292, P76CA-292C, or P76TA adapter for connection to the device under test. These adapters are ordered separately. Options Service options Opt. C3 Calibration Service 3 Years Opt. C5 Calibration Service 5 Years Opt. D3 Calibration Data Report 3 Years (with Opt. C3) Opt. D5 Calibration Data Report 5 Years (with Opt. C5) Opt. G3 Complete Care 3 Years (includes loaner, scheduled calibration, and more) Opt. G5 Complete Care 5 Years (includes loaner, scheduled calibration, and more) Opt. R3 Repair Service 3 Years (including warranty) Opt. R3DW Repair Service Coverage 3 Years (includes product warranty period). 3-year period starts at time of instrument purchase Opt. R5 Repair Service 5 Years (including warranty) Opt. R5DW Repair Service Coverage 5 Years (includes product warranty period). 5-year period starts at time of instrument purchase Accessories Standard accessories Accessory Quantity Tektronix part number Printed Manual 1 kit 071-3026-xx Data Calibration Report: Lists the manufacturing test results of your probe at the time of shipment 1 each Standard with probe Certificate of Traceable Calibration 1 each Standard with probe Antistatic wrist strap 1 each 006-3415-xx DC probe calibration fixture 1 each 067-3259-xx 50 Ω BNC-M to BNC-M cable assembly, 10 in. 1 each 012-0208-xx ESD protective cap 3 each 276-1152-xx Hex wrench, 2 mm 1 each 129-2781-xx Color band kit 1 kit 016-0633-xx Datasheet 6 www.tek.com

DC Probe Calibration Fixture Recommended accessories Description Tektronix part number 2.92 mm Coaxial Adapter P76CA-292 2.92 mm Coaxial Adapter with Cables P76CA-292C SMP Coaxial Adapter with Cables P76CA-SMP P7500 Tip Adapter P76TA P7500 TriMode Performance Solder Tip P75PST P7500 TriMode Long Reach Solder Tip P75TLRST P7500 TriMode Resistor Solder Tip 020-2936-xx P7500 TriMode Extended Resistor Solder Tip 020-2944-xx Solder Tip Ramps, Kit of 25 020-3118-xx Adhesive Tip Tape, Strip of 10 006-8237-xx Deskew Fixture 067-2431-xx SMPM Bullet Removal Tool 003-1934-xx SMPM Replacement Bullet Contacts (package of 4) 020-3105-xx G3PO Bullet Removal Tool 003-1896-xx G3PO Replacement Bullet Contacts (package of 4) 013-0359-xx Wire Kit 017-0103-xx Replacement Resistor Kit 020-2937-xx P7600 Series TriMode Probes www.tek.com 7

P7600 Series Probes Deskew Fixture P75PST Solder Tip Bullets and Bullet Removal Tool Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar. Product(s) complies with IEEE Standard 488.1-1987, RS-232-C, and with Tektronix Standard Codes and Formats. Datasheet 8 www.tek.com

P7600 Series TriMode Probes www.tek.com 9

ASEAN / Australasia (65) 6356 3900 Austria 00800 2255 4835* Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777 Belgium 00800 2255 4835* Brazil +55 (11) 3759 7627 Canada 1 800 833 9200 Central East Europe and the Baltics +41 52 675 3777 Central Europe & Greece +41 52 675 3777 Denmark +45 80 88 1401 Finland +41 52 675 3777 France 00800 2255 4835* Germany 00800 2255 4835* Hong Kong 400 820 5835 India 000 800 650 1835 Italy 00800 2255 4835* Japan 81 (3) 6714 3086 Luxembourg +41 52 675 3777 Mexico, Central/South America & Caribbean 52 (55) 56 04 50 90 Middle East, Asia, and North Africa +41 52 675 3777 The Netherlands 00800 2255 4835* Norway 800 16098 People's Republic of China 400 820 5835 Poland +41 52 675 3777 Portugal 80 08 12370 Republic of Korea +822 6917 5084, 822 6917 5080 Russia & CIS +7 (495) 6647564 South Africa +41 52 675 3777 Spain 00800 2255 4835* Sweden 00800 2255 4835* Switzerland 00800 2255 4835* Taiwan 886 (2) 2656 6688 United Kingdom & Ireland 00800 2255 4835* USA 1 800 833 9200 * European toll-free number. If not accessible, call: +41 52 675 3777 price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks of their respective companies.

23 May 2017 51W-28184-4

www.tek.com