01DT-5AH BELIMO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Technical data sheet 01DT-5A.. www.belimo.com 01DT-5A.. • en-us • 2019-08-20 • Subject to change 1 / 4 Duct / Immersion Temperature Sensor For measuring temperature in duct applications. In connection with a stainless steel or brass thermowell also applicable for pipe applications. IP65 / NEMA 4X rated enclosure. Type Overview Type Output signal Probe length Probe diameter 01DT-5AH Pt100 2" [50 mm] 0.24" [6 mm] 01DT-5AL Pt100 4" [100 mm] 0.24" [6 mm] 01DT-5AN Pt100 6" [150 mm] 0.24" [6 mm] 01DT-5AP Pt100 8" [200 mm] 0.24" [6 mm] 01DT-5AR Pt100 12" [300 mm] 0.24" [6 mm] 01DT-5AT Pt100 18" [450 mm] 0.24" [6 mm] Technical Data Electrical Data Electrical connection Removable spring loaded terminal block max. 2.5 mm² Cable entry Cable gland with strain relief Ø6...8 mm (1/2" NPT conduit adapter included) Functional Data Output signal passive temperature Pt100 Application air water Measuring Data Measuring values temperature Accuracy temperature passive ±0.5°F @ 32°F [±0.3°C @ 0°C] Time constant t (63%) in the air duct typical 210 s @ 0 m/s typical 46 s @ 3 m/s Time constant t (63%) in water pipe with thermowell A-22P-A.. and thermal contact fluid typical 7 s with thermowell brass typical 9 s with thermowell stainless steel Materials Cable gland plug adapter: PA66, black nut: PA6, black Housing cover: lexan, orange base: lexan, orange seal: 0467 NBR70, black UV resistant
Technical data sheet 01DT-5A.. www.belimo.com 01DT-5A.. • en-us • 2019-08-20 • Subject to change 2 / 4 Safety Data Ambient humidity max. 95% r.H., non-condensing Housing surface temperature max. 195°F [90°C] Protection class IEC/EN III safety extra-low voltage (selv) Protection class UL UL Class 2 Supply EU Conformity CE Marking Certification IEC/EN IEC/EN 60730-1 Certification UL cULus acc. to UL60730-1A/-2-9, CAN/CSA E60730-1:02/-2-9 Degree of protection IEC/EN IP65 Quality Standard ISO 9001 Safety Notes This device has been designed for use in stationary heating, ventilation and air-conditioning systems and must not be used outside the specified field of application. Unauthorised modifications are prohibited. The product must not be used in relation with any equipment that in case of a failure may threaten humans, animals or assets. Ensure all power is disconnected before installing. Do not connect to live/operating equipment. Only authorised specialists may carry out installation. All applicable legal or institutional installation regulations must be complied during installation. The device contains electrical and electronic components and must not be disposed of as household refuse. All locally valid regulations and requirements must be observed. Remarks Due to self-heating with 2 wire passive sensors, the supply wire current affects the measurement accuracy, so it should not exceed 1 mA. When using lengthy connecting cables (depending on the cross section used), the cable resistance must be taken into account. The lower the impedance of the sensor used, the greater the effect of the line resistance on the measurement, because it generates an offset. Scope of delivery Scope of delivery Description Type Mounting clip, with screws and adhesive foil A-22D-A11 1/2" NPT conduit adapter General Remarks Concerning Sensors
Technical data sheet 01DT-5A.. www.belimo.com 01DT-5A.. • en-us • 2019-08-20 • Subject to change 3 / 4 Accessories Optional accessories Description Type Mounting plate S housing A-22D-A09 Optional accessories air Description Type Mounting flange for sensor probe 6 mm, up to max. 80°C, Plastic A-22D-A03 Mounting flange for sensor probe 6 mm, up to max. 260°C, Brass A-22D-A05 Recommended accessories water Description Type Thermowell pocket (fabricated) Stainless steel, 2" [50 mm], 1/2" NPT, wrench size 3/4" A-22P-A05 Thermowell pocket (fabricated) Stainless steel, 4" [100 mm], 1/2" NPT, wrench size 3/4" A-22P-A07 Thermowell pocket (fabricated) Stainless steel, 6" [150 mm], 1/2" NPT, wrench size 3/4" A-22P-A09 Thermowell pocket (fabricated) Stainless steel, 8" [200 mm], 1/2" NPT, wrench size 3/4" A-22P-A11 Thermowell pocket (fabricated) Stainless steel, 12" [300 mm], 1/2" NPT, wrench size 3/4" A-22P-A13 Thermowell pocket (fabricated) Stainless steel, 18" [450 mm], 1/2" NPT, wrench size 3/4" A-22P-A15 Thermowell pocket (machined) Stainless steel, 2" [50 mm], 1/2" NPT, wrench size 3/4" A-22P-A36 Thermowell pocket (machined) Stainless steel, 4" [100 mm], 1/2" NPT, wrench size 3/4" A-22P-A37 Thermowell pocket (machined) Stainless steel, 6" [150 mm], 1/2" NPT, wrench size 3/4" A-22P-A38 Thermowell pocket (machined) Stainless steel, 8" [200 mm], 1/2" NPT, wrench size 3/4" A-22P-A39 Thermowell pocket (fabricated) Brass, 2" [50 mm], 1/2" NPT, wrench size 3/4" A-22P-A17 Thermowell pocket (fabricated) Brass, 4" [100 mm], 1/2" NPT, wrench size 3/4" A-22P-A19 Thermowell pocket (fabricated) Brass, 6" [150 mm], 1/2" NPT, wrench size 3/4" A-22P-A21 Thermowell pocket (fabricated) Brass, 8" [200 mm], 1/2" NPT, wrench size 3/4" A-22P-A23 Thermowell pocket (fabricated) Brass, 12" [300 mm], 1/2" NPT, wrench size 3/4" A-22P-A25 Thermowell pocket (fabricated) Brass, 18" [450 mm], 1/2" NPT, wrench size 3/4" A-22P-A27 Syringe with thermal paste A-22P-A44 Wiring Diagram
Technical data sheet 01DT-5A.. www.belimo.com 01DT-5A.. • en-us • 2019-08-20 • Subject to change 4 / 4 Dimensions Dimensions L = Probe length Type Probe length Weight 01DT-5AH 2" [50 mm] 0.26 lb [0.12 kg] 01DT-5AL 4" [100 mm] 0.26 lb [0.12 kg] 01DT-5AN 6" [150 mm] 0.29 lb [0.13 kg] 01DT-5AP 8" [200 mm] 0.29 lb [0.13 kg] 01DT-5AR 12" [300 mm] 0.31 lb [0.14 kg] 01DT-5AT 18" [450 mm] 0.33 lb [0.15 kg]