ZXLD1322 ZETEX | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 18
Technical content
Features
- 2.5V to 15V Input Voltage Range Up to 700mA output current Typical efficiency # >80% User-defined thermal control of LED output current using external thermistor High output current stability over input voltage and temperature 12µA typical standby current LED current adjustable from 100% down to 2% Adjustable Soft-Start Capable of driving 3 LEDs in series
Applications
High power LED flashlights LED back-up lighting General LED lighting
Issue 1 - January 2008 2 www.zetex.com © Zetex Semiconductors plc 2008 Pin connections (top-view) Package view Block diagram Package 14-Pin DFN with exposed pad 4mm x 3mm 0.50mm pitch 1.5W @TA=70°C 45° chamfer denotes Pin 1
Issue 1 - January 2008 3 www.zetex.com © Zetex Semiconductors plc 2008 Absolute maximum ratings (Voltages relative to GND unless otherwise stated) DC-DC converter High-side current monitor Switching NPN transistor These are stress ratings only. Operation outside the absolute maximum ratings may cause device failure. Operation at the absolute maximum ratings for extended periods may reduce device reliability. Thermal resistance Operating temperature (top) -40 to 125 °C Storage temperature (Tst) -55 to 150 °C Junction temperature (Tj) -40 to 150 °C Package power dissipation (Ptot) DFN-14 with exposed pad: 4mmx3mm, 0.5mm Pitch 1.5W at Tamb = 70 °C Supply voltage (VIN) -0.3V to +15V ADJ -0.3V to The lower of (+5.0V) or (VIN + 0.3V) CFB -0.3V to The lower of (+5.0V) or (VIN + 0.3V) ISENSE -0.3V to The lower of (+5.0V) or (VIN + 0.3V) TADJ -0.3V to The lower of (+5.0V) or (VIN + 0.3V) BIAS -0.3V to The lower of (+5.0V) or (VIN + 0.3V) Monitor supply voltage (M_VIN) -0.3V to +15V Continuous sense voltage (M_VIN – M_LOAD) -0.3V to +5V Collector-Base voltage (V CBO)1 8 V Collector-Emitter voltage (VCEO)1 8 V Peak pulse current (ICM) 3A (Pulse width = 300µs. Duty cycle<=2%) Continuous Collector current (IC)2 A Junction to case (R/H9052JC) Nominal value DFN-14 26.3°C/W
Issue 1 - January 2008 4 www.zetex.com © Zetex Semiconductors plc 2008 Pin description Name Pin # Description ADJ 1 Adjust input Leave floating, or connect to VREF to set 100% output current. Drive with dc voltage. (50mV<VADJ< VREF) to adjust output current from 10% to 100% of set value. (DC brightness control mode) Drive with low frequency (200Hz) PWM control signal to gate output ‘ on’ and ‘off’ at the PWM frequency. (PWM brightness control mode) Drive with low level dc voltage (VADJ<28mV) to turn off device (Standby mode) BIAS 2 Bias pin for setting base current of internal switch transistor Short pin to ground to define maximum base drive current for output switch (Maximum output current condition) Connect resistor (RBIAS) from this pin to ground to reduce base drive current (Reduced output current condition) CFB 3 Control input/output for feedback control loop Connect 10nF capacitor from this pin to ground to provide loop compensation N/C 4 Not connected internally (Open circuit) ISENSE 5 Switch peak current sense pin Connect resistor (Rsense) from this pin to ground to define peak switch current (ISWPEAK)=0.05/RS EMITTER1 6 Switch emitters (Connect both pins to top of RSENSE to sense emitter current)EMITTER2 7 COLLECTOR2 8 Switch Collectors (Connect both pins to lower side of coil)COLLECTOR1 9 N/C 10 Internally connected - Do not connect to external circuitry M_VIN 11 Input supply to high side current monitor Connect output voltage (whichever is higher) Connect resistor (R M) from this pin to to VIN to define nominal average output (LED) current of 0.1/RM VIN 12 Input supply voltage and load side input of high side current monitor. Connect to sensing resistor RM. TADJ 13 Temperature Adjust input for LED thermal compensation Connect thermistor/resistor network to this pin to reduce output current above a preset temperature threshold. Connect to VREF to disable thermal compensation function (see section on temperature control for details) VREF 14 Internal 0.5V reference voltage output Exposed pad 15 Connect to ground (0V)
Issue 1 - January 2008 5 www.zetex.com © Zetex Semiconductors plc 2008 Electrical characteristics (Test conditions: VIN = 4V, TAMB= 25°C unless otherwise stated(a)) DC-DC converter supply parameters NOTES: (a) Production testing of the device is performed at 25°C. Functional operation of the device and parameters specified from -40°C to +125°C are guaranteed by design, characterisation and process control. (b) Between 1.2V and 2.2V the device will run in the Low Voltage Startup Mode (for details refer to section "Low Voltage Operation") DC-DC converter input parameters Symbol Parameter Conditions Min Typ Max Units VIN Supply voltage Normal operation 2.5 15 V VIN(Start) Supply voltage for start-up (b) Start-up mode 1.2 2.4 V VUV- Under-voltage detection threshold normal operation to start-up mode VIN falling 1.8 V VUV+ Under-voltage detection threshold start-up mode to normal operation VIN rising 2.2 V Iq Quiescent current Measured into VIN ADJ pin floating. (Excluding switch base current). 1.5 mA ISTBY Standby current Measured into VIN. ADJ pin grounded 12 20 µA VREF Internalreference voltage ADJ pin floating 2.5V<VIN<15V 480 500 520 mV TCO(REF) Internal reference temperature coefficient. 50 ppm Symbol Parameter Conditions Min Typ Max Units VSENSE Peak switch current sense voltage Measured on ISENSE pin CFB pin at 0V 45 55 65 mV VSENSE (SU) Peak switch current sense voltage in start-up mode Measured on ISENSE pin. Start-up mode VIN=1.2V 10.5 mV ISENSE Sense input current Measured into ISENSE with pin at 0V.CFB pin at 0V -15 -7 -1 µA CFB Control loop compensation capacitor 10 nF VADJ External dc control voltage applied to ADJ pin to adjust output current DC brightness control mode 50 500 mV VADJ(th) Switching threshold of ADJ pin Standby state to Normal operation 26 28 30 mV TCO(VADJ) Temperature coefficient of VADJ(th) +0.3 %/K RADJ Internal resistor between VREF and ADJ VADJ<500mV 100 k Ω VADJ(clmp) Clamp voltage on ADJ pin 100µA injected into ADJ pin 575 mV
Issue 1 - January 2008 6 www.zetex.com © Zetex Semiconductors plc 2008 DC-DC convertertoutput parameters Switching NPN transistor NOTES: (c) Measured under pulse conditions. (d) This current is measured via the collectors and emitters of the switch with these connected to ground (0V) (e) Measured under pulse conditions. Peak Current = Ic Symbol Parameter Conditions Min Typ Max Units Toff(100) Discharge pulse width 100% output current 0.7 1.2 1.7 µs Toff(10) Discharge pulse width 10% output current 4 8 12 µs f LXmax Maximum operating frequency
600 KHz
fSU Switching frequency in start- up mode VIN=1.2V 50 KHz Symbol Parameter Conditions Min Typ Max Units ISW Average continuous switch current(c) IBON(max) Maximum base current into switch transistor from internal drive circuit (d) 2V<VIN<18V BIAS pin at 0V 30 50 70 mA I BON Base current into switch transistor using external resistor (R BASE) from BIAS pin to ground RBIAS = 1680Ω 10 mA V(BR)CE Collector-Emitter breakdown voltage IC=10µA 15 V VCE(sat) Collector-Emitter saturation voltage IC=0.1A, IB=10mA IC=2A, IB=50mA(e) 120 mV mV hFE Static forward current transfer ratio IC=200mA, VCE=2V IC=2A, VCE=2V 209 116 COBO Output capacitance V CB=10V,f=1MHz 64 pF t(on) Turn-on time Ic=0 to I C=2A VIN=10V 30 ns t(off) Turn-off time I C=2A to Ic<100µA 28 ns
Issue 1 - January 2008 7 www.zetex.com © Zetex Semiconductors plc 2008 High-side current monitor Reference current monitor LED thermal control circuit (TADJ) parameters Symbol Parameter Conditions Min Typ Max Units VM_VIN Supply voltage 2.5 18 V VMON Sense voltage =V(VIN) – VM_VIN 0 100 200 mV I_M_VIN Input current Measured into M_VIN pin 0.08 1 µA TCO (MON) Temperature coefficient VMON=10mV VMON=100mV 370 150 ppm/ K BW Bandwidth VMON=10mV VMON=100mV 350 2.5 KHz MHz Gm Transconductance /H9004Iout//H9004VMON 1m A / V Acc Accuracy RM = 0.1 Ω VMON = 100mV -3 3 % Symbol Parameter Conditions Min Typ Max Units VADJ Adjust voltage 0 500 mV TCO (MON) Temperature coefficient VADJ=50mV VADJ=500mV 160 200 ppm/ K BW Bandwidth VADJ=50mV VADJ=500mV 275 KHz MHz Gm Transconductance /H9004Iout//H9004VADJ 200 µA/V Acc Accuracy VADJ=500mV -3 3 % Symbol Parameter Conditions Min Typ Max Units VTADJH Upper threshold voltage Onset of output current reduction (VTADJ falling) 75 mV VTADJL Lower threshold voltage Output current reduced to <10% of set value (VTADJ falling) 50 mV Gm (TADJ) Transconductance /H9004Iout//H9004VTADJ 4m A / V
Issue 1 - January 2008 8 www.zetex.com © Zetex Semiconductors plc 2008 Output current regulation parameters NOTES: (f) System parameter only. This value is dependent upon external components and circuit configuration. (g) This refers to the accuracy of output current regulation under normal operation when the feedback loop incorporating the current monitor is active. The tolerances of external components are not included in this figure.
Ordering information
Symbol Parameter Conditions Min Typ Max Units IOUT Minimum output/ LED current(f) VIN>3V 0.75 A /H9004IOUT Output current accuracy(g) 3.0V<VIN<15V, Iout=700mA, VADJ=100mV -5 +5 % TCO (OUT) Output current temperature drift 3.0V<VIN<15V, Iout=700mA, VADJ=100mV 100 200 ppm/ K /H9004IOUT/ I OUT Load current regulation 350mA<I(LED)<700mA 2 %/A /H9004IOUT/ /H9004VIN Line voltage regulation of output current 0.5 %/V Eff Efficiency(f) 350mA<I(LED)<700mA 85 % Device Reel size (mm) Reel width (mm) Quantity per reel Device mark ZXLD1322DCTC 33.02 12 3,000 1322
Issue 1 - January 2008 9 www.zetex.com © Zetex Semiconductors plc 2008 Device description The ZXLD1322 is a buck/boost mode inductive DC-DC converter, with an internal switch, designed for driving single or multiple LEDs in series up to a total of 700mA output current. Depending upon supply voltage (V IN), LED forward voltage drop (V LED) and circuit config uration, this can provide up to 12W of output power. Applications cover VIN ranging from 2.5V to 15V. The device employs a modified Pulse Frequency Modulation (PFM) control scheme, with variable "ON" and "OFF" time control and adjustable peak switch current limiting. General device operation (refer to block diagram) Normal Operation Control is achieved by sensing the LE D current in a series resistor (R M), connected between the two inputs of the LED Current Monitor. This generates a proportional current (IMON) that charges the external integrator capacitor C FB. I MON is balanced against a reference discharge current (IADJ) generated at the output of a second voltage to current converter driven from the demand voltage (VADJ) on the ADJ pin. The difference between I MON and I ADJ is integrated by C FB to produce an error voltage. A comparator takes a summed version of the voltage at the ISENSE pin and a fraction of this CFB voltage and resets the latch driving the switch when the sum is greater than 50mV. The switch transistor is turned on by the output of the SR latch, which remains set until the emitter current in the switch transistor produces a voltage drop Vsense (=50mV nominal) in external resistor Rsense, defining a preset maximum switch current of 50mV/Rsense. Operation is such that a rising error voltage on CFB will effectively lower the voltage required on the ISENSE pin and therefore reset the latch earl ier in the switching cycle. This will reduce the 'ON' time of the switch and reduce the peak current in the switch from its preset maximum value. Similarly, a falling error voltage will reset the latch later and the peak switch current will be increased. The control loop therefore reduces or increases the energy stored in the coil during each switching cycle, as necessary, to force the LED current to the set value. This results in high accuracy, as no error is needed in the LED current to drive the servo to the required region. The time taken for the coil current to reach the peak value depends on several factors: the supply voltage, the peak coil current required at that particular LED power and whether the system operates in "continuous" or "discontinuous" m ode. The time allowed for the coil current to discharge into the LED is fixed by the 'Variable Off Delay' monostable, whose period is modified by the power demand signal on the ADJ pin. This monostable determines the time for which the latch remains reset (switch off) and provides a longer "OFF" period at lower power settings, helping to keep the parameters within an acceptable range. Note that the "ON" period and the "OFF" period are set by the supply voltage, LED power and external components chosen. The frequency is therefore determined by these parameters and is NOT fixed. In this mo dified PFM scheme, the external components can be chosen to keep the frequency well above the audio range for all extremes of parameters, so no audible whistling should ever occur. The 500mV reference voltage defines the nominal VADJ voltage and this defines the 100% output current. For lower LED currents, the ADJ pin can be-driven from an external dc voltage (50mV<VADJ<500mV) or a low frequency Pulse Width Modulated (PWM) waveform.
Issue 1 - January 2008 10 www.zetex.com © Zetex Semiconductors plc 2008 Low voltage operation (start-up mode) For supply voltages below 2V, the normal control loop will have insufficient headroom to operate reliably. This condition is detected by the 'under-voltage comparator', which compares a fraction of the internal supply voltage (Vcc) against VREF. When the comparator output is active (VCC<1.8V), the output of the normal switch drive circuit is disabled and an alternative 'Start-up oscillator and driver' enabled. The start-up osci llator provides a nominal 50kHz fixed frequency drive signal to the base of the switch transistor, which is independent of VADJ and the voltage on CFB. Under low voltage conditions, the peak current in the coil ramps to approximately 25% of the normal value and the "OFF" time is fixed. The low voltage start-up mode allows the device to operate down to 1.2V nominal. This allows the chip to work from a single cell. ADJ pin The ADJ pin is connected to the internal 500mV reference (VREF) via a 100k resistor. This biases the ADJ pin to the reference voltage and defines nominal 100% LED current. The ADJ pin can be overdriven with an external dc voltage between 50mV and 500mV to reduce the LED current proportionally between 10% and 100% of the nominal value. LED current can also be adjusted by applying a low frequency PWM signal to the ADJ pin to turn the device On and Off. This will produce an average output current proportional to the duty cycle of the control signal. The device can be shut down by shorting the ADJ pin to ground, or pulling it to a voltage below 28mV with a suitable open collector NPN or open drain NMOS transistor. In the shutdown state, most of the circuitry inside the device is sw itched off and residual quiescent current will be typically 12µA. Thermal control of LED current The 'Thermal compensation current' circuit produce s a sourcing current (Itc) which is zero for voltages above 75mV on TADJ and increases to 100µA when TADJ falls to 50mV. This current is summed into the control node and subtracted from the demand current, causing LED current to reduce from 100% down to zero over this input range. The potential divider, consisting of a fixed resistor Rt and an NTC Thermistor Rth between VREF and ground, defines the voltage on TADJ and sets the threshold temperature. Further details are given in the application notes. The Thermal Control feature can be disabled by leaving the TADJ pin floating, or by connecting it to VREF. Over-temperature shutdown The ZXLD1322 incorporates an over-temperature shutdown circuit to protect the device against damage caused by excess die temperature, resu lting from excessive power dissipation in the switch. The output of the 'Over-temp Shutdown' circuit will go high when the die temperature exceeds 150°C (nominal). This will turn off the drive to the switch during normal operation. Operation will resume when the device has cooled to a safe level.
Issue 1 - January 2008 11 www.zetex.com © Zetex Semiconductors plc 2008 Application notes Setting peak coil current The peak current in the coil is set by the resistor (RSENSE) between the switch emitter and ground according to The minimum peak current will depend on opera ting mode, coil inductance and supply voltage range. The maximum peak current must not exceed the specified value for the switch. (See Application circuits for details) Setting LED current The nominal average LED current is given by Where R M is the external resistor connected between pins M_VIN and VIN. This current can be adjusted to a lower value by applying a dc control voltage or PWM control signal to the ADJ pin. DC control The LED current can be adjusted over a 10% to 100% range by connecting a variable resistor R ADJ from the ADJ pin to ground to vary the dc voltage at the ADJ pin. RADJ forms the lower part of a resistive divider and the internal 100kΩ resistor between the ADJ and VREF pins forms the upper part. A value of 1MΩ for RADJ will therefore give a maximum current of 91% of ILED (nom) and the device will be turned off when the voltage on the ADJ pin falls below 28mV, corresponding to an R ADJ value of approximately 5kΩ. If required, an end-stop resistor in series with RADJ can be used to maintain the voltage on the ADJ pin above the turn-on threshold. Using a logarithmic potentiometer for RADJ will give an approximately linear variation of output current with shaft rotation. (Fig 1) If required, the maximum output current can be re stored to 100% by adjusting the value of the LED current monitor resistor (RM). The tolerance of the internal 100k resistor and RADJ should be taken into account when calculating output current. The ADJ pin is clamped internally to a voltage of 575mV (nom), to limit maximum average output current to approximately 115% of ILED(nom). Rsense mVISWpeak 50= M LED R mVnomI 100)( =
Issue 1 - January 2008 12 www.zetex.com © Zetex Semiconductors plc 2008 Fig 1 PWM control A wider dimming range can be achieved by applying a PWM control signal to the ADJ pin to turn the device on and off, giving an average output current proportional to the duty cycle of the control signal. The ADJ pin can be driven directly from the open drain NMOS output of a microcontroller, or indirectly with a low satu ration voltage NPN transistor such as the Zetex ZXTN25015DFL. (Fig 2). Fig 2 In the circuit of Fig 4, the average LED output current will be Where duty cycle A PWM frequency of 200Hz, or lower is recommended, to minimize errors due to the rise and fall times of the converter output. ZXTN25015DFL ADJ ZXLD1322 DnomIavgI LEDLED *)()( = )21( TT TD +=
Issue 1 - January 2008 13 www.zetex.com © Zetex Semiconductors plc 2008 Thermal compensation of LED current High-luminance LEDs often need to be supplied with a temperature compensated current in order to maintain stable and reliable operation at high temperatures. This is usually achieved by reducing the LED current proportionally from its nominal set value when the LED temperature rises above a predefined threshold. (Fig.3) Fig 3 The 'Thermal compensation current' generator inside the ZXLD1322 provides the necessary thermal compensation current to meet this requirement, using an NTC thermistor and resistor. (Fig 4) Fig 4 The TADJ pin of the device has a voltage thresh old of 75mV nominal, which is derived from the reference voltage VREF. If the voltage (V TADJ) on the TADJ pin is held above the threshold, the thermal compensation current will be zero and no thermal compensation is applied. However, if V TADJ falls below the threshold, a thermal compensation current (I TC) is produced that is proportional to VTADJ. ITC is injected into the control loop in such a way as to reduce the demand current I ADJ, causing the control loop to decrease the LED current. The LED current will be reduced to less than 10% of the set value when VTADJ falls below 50mV. The threshold voltage has been chosen to set a nominal threshold of 105 °C and the device has been optimized to operate with a standard 103KT1608 thermistor and 5k resistor in the potential divider. Circuit details are given in the application notes. Alternative thermistor/resistor networks can be used providing the input resistance presented to the device at the TADJ pin is similar at the threshold temperature. If no LED thermal co mpensation is required, the TADJ pin should be connected to VREF to disable this function. ILED LED temperature
Issue 1 - January 2008 14 www.zetex.com © Zetex Semiconductors plc 2008 Typical operating conditions Inductive converters can operate in either C ONTINUOUS mode, where current always flows in the inductor, but rises during the ON period and falls during the OFF period, or DISCONTINUOUS mode, where the current falls to zero during the OFF period. The mode depends on several factors, including supply voltage, output (LED) voltage and the choice of peak current and inductor value. Calculations need to be done to determine which mode the converter will be in. The circuit should be designed to give slightly more LED current than required under the lowest supply voltage, so the control loop can regulate th e current accurately. If the theoretical LED current is less than that required, the control loop will not be able to reach the required value. The calculations will give an idea of the ON and OFF times and hence the operating frequency, but bear in mind that the control loop will reduce the peak current to achieve the exact programmed LED current and this will raise the operating fre quency. In general, values in the discontinuous mode are simpler to calculate because the current can go from zero to the theoretical maximum during the ON period and fall to zero during the OFF period. In continuous mode the current will start from some value, so the ON time will be lower to reach the theoretical maximum and lower still when the control loop reduces the peak current below the maximum. Circuit operation Operation of buck / boost LED driver Used when the input voltage can go higher or lower than the LED voltage, this circuit has an ON phase, where the coil is connected from the su pply to ground and an OFF phase, where the coil current flows through the LED via a Schottky diode. The current therefore only flows into the LED circuit during the OFF phase, although the reservoir capacitor C3 should keep current flowing in the LED(s) continuously. The important difference is that this circuit has the LED cathode taken to VIN instead of ground. ADJ is set between 50mV and 500mV to give between 10% and 100% power respectively. Making R2 = ZERO gives a base current to the output transistor of 50mA nominal and making R2 = 1.68kΩ gives 10mA nominal. The reduced base current will lower supply current and hence improve efficiency in lower power applications. Making R1 = 25m Ω gives a peak coil current of 2 Amps. The internal power transistor turns on until the coil current builds up to the peak value. At this
Issue 1 - January 2008 15 www.zetex.com © Zetex Semiconductors plc 2008 point the transistor switches off and the coil current continues to flow in the LED(s) via the Schottky diode D1. With a buck converter, the LED is in series with the coil, so no coil current can flow until the supply voltage exceeds the LED forward drop. The circuit will not work if the supply is less than this. With a boost converter, there is always a pa th from supply to ground through the coil, Schottky diode and LED in series, so if the supply voltage is greater than the LED and Schottky forward drops, unlimited current will flow in the LED. The circuit will not work if the supply is greater than this. Thus neither circuit will work for both conditions, where the supply could be either higher or lower than the LED forward drop, for example when using 3 cells to supply it. Although it looks like a boost circuit, taking the LED cathode to the supply means that no current can flow in the LED even if the supply is greater than the forward drop. However, because the coil is still connected straight across the supply during the ON phase, the current can still be established when the supply is less than the LE D forward drop. Hence this circuit will work at supply voltages above and below the forward LED drop. This mode is useful for example when using 3 cells and a white LED, where the voltage of 3 fully charged alkaline cells is more than the LED forward drop, but the voltage of 3 partly discharged rechargeable NiCd cells is less than the LED forward drop. The LED current is sensed by R3 and the controller varies this until the drop in R3 equals 20% of V ADJ. Hence making R3 = 100m Ω and VADJ = 500mV gives a LED current of 1 Amp because the 500mV VADJ results in 100mV across R3 which equals 1 Amp. Making VADJ = 10mV gives a LED current of 100mA because the 50mV VADJ results in 10mV drop across R3 which equals 100mA. The power is controlled by the chip backing off the peak coil current, so it is necessary to calculate the coil inductance and current to guarantee slightly more than 100% LED power, so the circuit can control it effectively. The internal control loop is compensated by C1, which is normally 10nF. If the thermistor (R5) is used, the power will be backed off progressively as the TADJ pin goes low. With the TADJ pin above 75mV, power is 100% and this is reduced to zero when the TADJ pin reaches 50mV. Making R4 = 5k Ω and using a 103KT1608 thermistor, the thermistor will reach 869Ω at 105°C giving V TADJ = 74mV which will start to reduce the LED power above 105°C. By 125°C the thermistor will reach 547 Ω giving V TADJ = 50mV which gives zero power. This will protect the LED from damage. These temperature values can be set by the customer by using a different thermistor or a different value of R4. If protection is not required, leaving the TADJ pin open circuit will make it float to a high voltage and always give 100% power. Bill of materials Reference Part No Value Manufacturer Contact Details U1 ZXLD1322 LED Driver Zetex www.zetex.com D1 ZXCS2000 Schottky diode Zetex L1 MSS7341-103ML 10µH 2A Coilcraft www.coilcraft.com L1 NPIS64D100MTRF 10µH 2A NIC www.niccomp L1 744 777910 10µH 2A Wurth www.wurth.co.uk C1 Generic 10nF 10V Generic 0603 C2 GRM31CR71H475K 4.7µF 50V Murata 1206 www.murata.com C3 GRM31MR71E225K 2.2µF 25V Murata 1206 www.murata.com R1 Generic 25m Ω Generic 0805 R2 Generic 1.5k Ω Generic 0603 R3 Generic 100m Ω Generic 0805 R4 Generic 5.1k Ω Generic 0603 R5 Thermistor NTC 10k 103kt1608
Issue 1 - January 2008 16 www.zetex.com © Zetex Semiconductors plc 2008 Additional notes Note that the ON time is set by the time it takes the coil to reach the peak current. This peak value is reduced by the control loop to give the desired LED power, so the ON time can vary over a wide range. The minimum coil current can be zero (d iscontinuous operation) or finite (continuous operation) depending on the supply voltage, LED current and the LED voltage. The OFF time is set by an internal timer and is nominally 1.2µs at 100% LED power (VADJ = 500mV), increasing to about 8µs at 10% LED power (VADJ = 50mV). The longer OFF time and variable peak current enables the circuit to dim the LED whilst maintaining continuous switching, rather than "skipping" or stalling and continuous running is better for reducing electrical noise and also for eliminating audible noise from the coil core. Layout considerations As with all switching DC to DC converters, the currents can be large. Using small inductors with a reasonable high supply voltage wi ll cause currents to change quickly. High dI/dt can cause inductively-coupled spikes into adjacent tracks. At the transition from of the ON phase to the OFF phase and back, where the power transistor switches, the voltage at the collector rises and falls quickly. High dV/dt can cause capacitively coupled spikes into adjacent tracks, especially if they have a high impedance. For this reason, all tracks on the PCB should be thick, to minimise drops, and short to keep all the components coupled tightly together. A double-sided board should be used with a ground plane to screen the tracks and provide a good ground return for the various functions and the rear exposed pad on the package should have an appropriately-sized land with good ground connecti ons, both to reduce electrical noise due to ground drops and to improve thermal conductivity. The input decoupling capacitor C1 should be ver y close to the chip pins and the LED sense resistor R3 should have Kelv in tracks to M_VIN and VIN to achieve LED current measurement accuracy, as the PCB tracks will have comparable resistance to the 100m Ω resistor, so taking sense tracks to the current monitor which are not connected close to the ends of R3 will cause a measurement error. The peak current sense resistor R1 should have short tracks to the ground at the bottom end and Kelvin tracks to ISENSE at the top end. This resistor might need to be only 25m Ω and PCB track resistance becomes comparable if the tracks are not very short. ISENSE is a high impedance input, so a thin track from this pin directly to the top of R SENSE resistor R1 will still give an accurate measurement. The ADJ pin should have short tracks, as this is a fairly low-level signal controlling the power of the system. As it needs to be less than 28mV for shutdown, a close ground connection is needed for the pull-down device, as any ground drops could raise the potential. In particular, if a bipolar transistor is used as a pull-down device, this will have an appreciable VSAT, which could perhaps be half the shutdown potential. The bottom of the thermistor must be coupled very closely to ground, as the TADJ pin varies the LED current from 100% to 0% for a voltage change of only 25mV, so any noise on the bottom of the thermistor will seriously affect the accuracy of the Thermal Protection circuit.
Issue 1 - January 2008 17 www.zetex.com © Zetex Semiconductors plc 2008 Note: Controlling dimensions are in millimeters. Approximate dimensions are provided in inches DIM Inches Millimeters DIM Inches Millimeters Min Max Min Max Min Max Min Max E D A b L PIN 1 DOT BY MARKING CHAMFER 0.300 X 45° PIN #1 IDENTIFICATION
Issue 1 - January 2008 18 www.zetex.com © Zetex Semiconductors plc 2008 Zetex sales offices Europe Zetex GmbH Kustermann-park Balanstraße 59 D-81541 München Germany Telefon: (49) 89 45 49 49 0 Fax: (49) 89 45 49 49 49 europe.sales@zetex.com Americas Zetex Inc
700 Veterans Memorial Highway
Hauppauge, NY 11788 USA Telephone: (1) 631 360 2222 Fax: (1) 631 360 8222 usa.sales@zetex.com Asia Pacific Zetex (Asia Ltd) 3701-04 Metroplaza Tower 1 Hing Fong Road, Kwai Fong Hong Kong Telephone: (852) 26100 611 Fax: (852) 24250 494 asia.sales@zetex.com Corporate Headquarters Zetex Semiconductors plc Zetex Technology Park, Chadderton Oldham, OL9 9LL United Kingdom Telephone: (44) 161 622 4444 Fax: (44) 161 622 4446 hq@zetex.com © 2008 Published by Zetex Semiconductors plc Definitions Product change Zetex Semiconductors reserves the right to alter, without notice, specifications, design, price or conditions of supply of any product or service. Customers are solely responsible for obtaining the latest relevant information before placing orders. Applications disclaimer The circuits in this design/application note are offered as desi gn ideas. It is the responsibility of the user to ensure that t he circuit is fit for the user’s application and meets with the user’s requirements. No representation or warranty is given and no liability whatsoev er is assumed by Zetex with respect to the accuracy or use of such in formation, or infringement of patents or other intellectual prop erty rights arising from such use or otherwise. Zetex does not assume any le gal responsibility or will not be held legally liable (whether in contract, tort (including negligence), breach of statutory duty, restricti on or otherwise) for any damages, loss of profit, business, con tract, opportunity or consequential loss in the use of these circuit applications, under any circumstances. Life support Zetex products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Zetex Semiconductors plc. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body or 2. support or sustain life and whose failure to perform when proper ly used in accordance with instructions for use provided in the labelling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support devi ce or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Reproduction The product specifications contained in this publication are issu ed to provide outline information only which (unless agreed by the company in writing) may not be used, applied or reproduced for any purpose or form part of any order or contract or be regarded as a representation relating to the products or services concerned. Terms and Conditions All products are sold subjects to Zetex’ terms and conditions of sale, and this disclaimer (save in the event of a conflict bet ween the two when the terms of the contract shall prevail) according to region, supplied at the time of order acknowledgement. For the latest information on technology, delivery terms and conditions and prices, please contact your nearest Zetex sales office. Quality of product Zetex is an ISO 9001 and TS16949 certified semiconductor manufacturer. To ensure quality of service and products we strongly advise the purchase of parts dire ctly from Zetex Semiconductors or one of our regionally authorized distributors. For a complete listing of authorized distributors please visit: www.zetex.com/salesnetwork Zetex Semiconductors does not warrant or accept any liability whatsoever in respect of any parts purchased through unauthorized sales channels. ESD (Electrostatic discharge) Semiconductor devices are susceptible to damage by ESD. Suitable precautions should be taken when handling and transporting devices. The possible damage to devices depends on the circumstances of the handling and transporting, and the nature of the device. The extent of damage can vary from immediate functional or parametric malfunc tion to degradation of function or performance in use over ti me. Devices suspected of being affected should be replaced. Green compliance Zetex Semiconductors is committed to envir onmental excellence in all aspects of its operations which includes meeting or exce eding regulatory requirements with respect to the use of hazardous s ubstances. Numerous successful programs have been implemented to reduce the use of hazardous substances and/or emissions. All Zetex components are compliant with the Ro HS directive, and through this it is supporting its customers in their compliance with WEEE and ELV directives. Product status key: “Preview” Future device intended for production at some point. Samples may be available “Active” Product status recommended for new designs “Last time buy (LTB)” Device will be discontinued and last time buy period and delivery is in effect “Not recommended for new designs” Device is still in production to support existing designs and production “Obsolete” Production ha s been discontinued Datasheet status key: “Draft version” This term denotes a very early datasheet ver sion and contains highly provisional information, which may change in any manner without notice. “Provisional version” This term denotes a pre-release datasheet. It provides a clear indication of anticipated performance. However, changes to the test conditions and specifications may occur, at any time and without notice. “Issue” This term denotes an issued datasheet cont aining finalized specifications. However, changes to specifications may occur, at any time and without notice.