ZXFV301 ZETEX | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 12

Technical content

The ZXFV301 is a 4:1 high speed analog switch designed for use as a buffered video multiplexer and other high-speed applications. It features low different gain and phase distortion. The high speed high output current capability provides 75/H9024 cable drive for use in high performance video applications. The input channel is selected by means of four logic lines. An output enable line allows expansion to eight channels using two devices ZXFV301 as shown in the example application figure 1. An alternative device, ZXFV302 has a seperate datasheet and provides the same functionality and pin-out as the ZXFV301 but with only two logic lines controlling the switch via a decoder. FEATURES AND BENEFITS

  • 3dB Bandwidth 300MHz
  • Slew rate 450V/ /H9262s
  • Differential gain 0.01%
  • Differential phase 0.04/H11034
  • Output current 40mA
  • Stable up to 100pF load
  • /H110065 Volt supply
  • Supply current 19mA
  • 16 pin SO package

APPLICATIONS

  • Video routing and switching
  • CCTV switching
  • Video distribution selection
  • RGB multiplexing
  • High frequency instrumentation Data acquisition
  • Data acquisition ZXFV301 ISSUE 2 - NOVEMBER 2002 4:1 HIGH SPEED MULTIPLEXER Part Number Container Increment ZXFV301N16TA Reel 7 ″ 500 ZXFV301N16TC Reel 13 ″ 2500

Ordering information

Fig.1:Typical Application for 8 channel CCTV

Supply voltage VCC -0.5V to +6V Supply voltage VEE -6V to +0.5V Analog inputs to ground V EE -0.5V to VCC +0.5V Digital inputs to ground -0.5V to V CC +0.5V Outputs to ground* V EE -0.5V to VCC +0.5V Output current, max continous 40mA Operating Ambient Temperature Range -40 /H11034C to 85/H11034C Storage -65/H11034C to 150/H11034C Operating Junction temperature TJMAX 150/H11034C The thermal resistance from the semiconductor die to ambient is typically 120/H11034C/W when the SO16 package is mounted on a PCB in free air. The power dissipation of the device when loaded must be designed to keep the device junction temperature below T JMAX. *During power-up and power-down, these voltage ratings require an appropriate sequence of applying and removing signals and power supplies. ZXFV301 ISSUE 2 - NOVEMBER 2002 PARAMETER CONDITIONS TEST MIN TYP MAX UNIT Supply Voltage V+ 4.75 5 5.25 V Supply Voltage V- -5.25 -5 -4.75 V Positive supply current P 15 19 22 mA Negative supply current P 9 14 18 mA Voltage gain DC P 0.99 1.000 1.01 V/V Input Common mode Voltage P /H110063V Input resistance P 35 45 55 k /H9024 Output offset Voltage All channels held at 0V P -10 +10 +30 mV Input bias current Active channels held at 0V P -25 -11 +5 /H9262A Output Voltage swing P /H110063V Output drive current P 40 mA Output resistance C 1 /H9024 Output resistance Disabled (EN low) P 1.5 3 4.5 M /H9024 Positive PSRR P 40 54 dB Negative PSRR C 30 51 dB Small signal bandwidth

1 C 300 MHz

Slew rate, 25% to 75% 2V pk-pk C 450 V/ /H9262s Logic input HIGH V Hmin C2 V Logic input LOW V Lmax C 0.8 V Logic input current I INHIGH logic input voltage = 5V C 5 pA Logic input current I INLOW logic input voltage = 0V C -70 /H9262A

ELECTRICAL CHARACTERISTICS

/H110065V power supplies, Tamb = 25/H11034C unless otherwise stated. RL = 150/H9024, CL = 10pF Characteristics apply to channel selected, and EN input HIGH unless otherwise stated Test level: P = 100% production test C = characterised only

PARAMETER CONDITIONS TEST MIN TYP MAX UNIT tON Vout = /H110062V, see timing diagram C 35 ns tOFF Vout = /H110062V, see timing diagram C 10 ns tLOW Vout = /H110062V, see timing diagram C 50 ns tHIGH Vout = /H110062V, see timing diagram C 40 ns Cross-talk, all hostile 1 10MHz, 0dBm in C 75 dB Differential Gain C 0.01 % Differential Phase C 0.04 deg Switching transients, magnitude All channels held at 0V C 50 mV Switching transients, duration All channels held at 0V C 25 ns /H110065V power supplies, Tamb = 25/H11034C unless otherwise stated. RL = 150/H9024, CL = 10pF Characteristics apply to channel selected, and EN input HIGH unless otherwise stated Test level: P = 100% production test C = characterised only Notes: 1. Bandwidth and cross talk measured using Zetex Evaluation Circuit Board detailed later in this datasheet. EN SELECT OUT tOFF 10% 90% tON 10% t LOW Notes: The ‘select’ waveform represents a change in the channel selected (see Truth Table). tHIGH is equivalent to tLOW but , applies for a positive going transition of OUT. Fig.2: TIMING DIAGRAM SEL1 SEL2 SEL3 SEL4 EN OUT XXXX0 H i Z

01111 I N 1

11111 H i Z

Truth table for selection of input channel

-25 -20 -15 -10 0.1 1 10 100 1000-105 -100 -95 -90 -85 -80 -75 -70 -65 -60 -55 -50 0.1 1 10 100 1000-105 -100 -95 -90 -85 -80 -75 -70 -65 -60 -55 -50 0.1 1 10 100 1000-105 -100 -95 -90 -85 -80 -75 -70 -65 -60 -55 -50 CL=10pF CL=0pF Vin = 0dBm Av = +1 Frequency Response dB Frequency (MHz) Vin = 10dBm Av = +1 Typical All Hostile Cross Talk dB Frequency (MHz) Vin = 10dBm Av = +1 Vin = 10dBm Av = +1 Typical Disabled Cross Talk dB Frequency (MHz) Feed-through Vs Frequency Unselected Channel dB Frequency (MHz) CHARACTERISTICS

Figure 4. These circuits are suitable for 75 /H9024 amplifier load is then 150/H9024. output can be provided if required). be solid tantalum electrolytic or ceramic types. overall loss when loaded by 75/H9024is also 15.45 dB.

4 R1,R2,R3,R4 51R 0805

4 R5,R6,R7,R8 22k 0805

1 R9 120R 0805

1 R10 62R 0805

1 R11 10R 0805

5 R12 to R16 47k 0805

10 TP1 to TP10 /H5007PCB test terminal,

Figure 3: BASIC APPLICATION CIRCUIT, 4 CHANNEL DC COUPLED, DUAL SUPPLIES

Figure 4: CCTV CIRCUIT WITH 8 CAMERA FROM SINGLE SUPPLY

Figure 5: EVALUATION CIRCUIT & PRINTED BOARD LAYOUT SHOWING TOP COPPER (overall dimensions 4x3 inches)

Figure 6: EVALUATION CIRCUIT BOARD BOTTOM COPPER (viewed through from top)

Oldham, OL9 8NP United Kingdom Telephone (44) 161 622 4422 Fax: (44) 161 622 4420 uk.sales@zetex.com Zetex GmbH Streitfeldstraße 19 D-81673 München Germany Telefon: (49) 89 45 49 49 0 Fax: (49) 89 45 49 49 49 europe.sales@zetex.com Americas Zetex Inc

700 Veterans Memorial Hwy

Hauppauge, NY11788 USA Telephone: (631) 360 2222 Fax: (631) 360 8222 usa.sales@zetex.com Asia Pacific Zetex (Asia) Ltd 3701-04 Metroplaza, Tower 1 Hing Fong Road Kwai Fong Hong Kong Telephone: (852) 26100 611 Fax: (852) 24250 494 asia.sales@zetex.com These offices are supported by agents and distributors in major countries world-wide. This publication is issued to provide outline information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose or form part of any order or contract or be regarded as a representation relating to the products or services concerned. The Company reserves the right to alter without notice the specification, design, price or conditions of supply of any product or service. For the latest product information, log on to www.zetex.com © Zetex plc 2002 PACKAGE OUTLINE DIM Millimetres Inches MIN MAX MIN MAX A 9.80 10.00 0.386 0.394 B 1.27 BSC 0.05 BSC C 0.53 REF 0.02 REF D 0.33 0.51 0.013 0.020 E 3.80 4.00 0.15 0.157 F 1.35 1.75 0.053 0.069 G 0.10 0.25 0.004 0.01 H 0 °8 °0 °8 ° I 0.40 1.27 0.016 0.05 J 5.80 6.20 0.228 0.244 Conforms to JEDEC MS-012AC Iss C (SO16N)