XPEBWT-01-0000-00EC2

XPE2 CREE | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 12

Technical content

Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. CLD-DS56 Rev 0 cree Xlamp XP-e2 leds Product descriPtion The XLamp XP-e2 LeD builds on the unprecedented performance of the original XP-e by increasing lumen output up to 20% while providing a single die LeD point source for precise optical control. The XP- e2 LeD shares the same footprint as the original XP-e, providing a seamless upgrade path to more lumens and/or greater efficiency while shortening the design cycle for existing XP customers. XLamp XP-e2 LeDs are the ideal choice for lighting applications where high light output and maximum efficacy are required, such as LED retrofit lamps, outdoor lighting, portable lighting, or indoor directional lighting.

features

• Available in white, outdoor white, 80-CRI, 85-CRI and 90-CRI white
• ANSI-compatible chromaticity bins
• Binned @ 85 °C
• Maximum drive current: 1 A
• Low thermal resistance: 9 °C/W
• Wide viewing angle: 110°
• Unlimited floor life at ≤ 30 °C/85% RH
• Reflow solderable - JEDEC J-STD- 020C compatible
• Electrically neutral thermal path WWW. CREE.CoM/XLAMp Cree, Inc.

4600 Silicon Drive

Durham, NC 27703 USA Tel: +1.919.313.5300 table of contents Relative Spectral Power Relative Flux vs. Junction Relative Chromaticity vs. Current and Temperature - Warm White ... 6 Reflow Soldering Characteristics .. 8

Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. xlamp xp-e2 leds fluX characteristics (tJ = 85 °c) The following table provides several base order codes for XLamp XP-e2 LeDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp XP Family Binning and Labeling document. color cct range base order codes min. luminous flux (lm) @ 350 ma calculated minimum luminous flux (lm)** @ 85 °c order code min. max. Group flux (lm) @ 85 °c flux (lm) @ 25 °c* 700 ma 1.0 a Cool White 5000 K 10,000 K Q4 100 116 171 218 XpEBWT-L1-0000-00C51 Q5 107 124 183 233 XpEBWT-L1-0000-00D51 R2 114 132 195 249 XpEBWT-L1-0000-00E51 R3 122 142 209 266 XpEBWT-L1-0000-00F51 outdoor White 4000 K 5300 K Q4 100 116 171 218 XpEBWT-01-0000-00CC2 Q5 107 124 183 233 XpEBWT-01-0000-00DC2 R2 114 132 195 249 XpEBWT-01-0000-00EC2 R3 122 142 209 266 XpEBWT-01-0000-00FC2 Neutral White 3700 K 5300 K Q4 100 116 171 218 XpEBWT-L1-0000-00CE4 Q5 107 124 183 233 XpEBWT-L1-0000-00DE4 R2 114 132 195 249 XpEBWT-L1-0000-00EE4 80-CRI White 2600 K 4300 K Q2 87.4 101 150 191 XpEBWT-H1-0000-00AE7 Q3 93.9 109 161 205 XpEBWT-H1-0000-00BE7 Warm White 2600 K 3700 K Q2 87.4 101 150 191 XpEBWT-L1-0000-00AE7 Q3 93.9 109 161 205 XpEBWT-L1-0000-00BE7 Q4 100 116 171 218 XpEBWT-L1-0000-00CE7 85-CRI White 2600 K 3200 K P2 67.2 78.0 115 147 XpEBWT-p1-0000-007E7 p3 73.9 85.7 127 161 XpEBWT-p1-0000-008E7 P4 80.6 93.5 138 176 XpEBWT-p1-0000-009E7 Q2 87.4 101 150 191 XpEBWT-p1-0000-00AE7 90-CRI White 2600 K 3200 K P2 67.2 78.0 115 147 XpEBWT-U1-0000-007E7 p3 73.9 85.7 127 161 XpEBWT-U1-0000-008E7 P4 80.6 93.5 138 176 XpEBWT-U1-0000-009E7 Notes:

• Cree maintains a tolerance of ± 7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
• Typical CRI for Cool White (5000 K – 10,000 K CCT) is 70.
• Typical CRI for Neutral White (3700 K – 5300 K CCT) is 75.
• Typical CRI for outdoor White (4000 K - 5300 K CCT) is 70.
• Typical CRI for Warm White (2600 K – 3700 K CCT) is 80.
• Minimum CRI for 80-CRI White is 80.
• Minimum CRI for 85-CRI White is 85.
• Minimum CRI for 90-CRI White is 90. * Flux values @ 25 °C are calculated and for reference only. ** Calculated flux values are for reference only.

Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. xlamp xp-e2 leds characteristics characteristics unit minimum typical maximum Thermal resistance, junction to solder point °C/W 9 Viewing angle (FWHM) degrees 110 Temperature coefficient of voltage mv/°C -2.3 ESD classification (HBM per Mil-Std-883D) Class 2 DC forward current mA 350 1000 Reverse voltage v -5 Forward voltage (@ 350 mA, 85 °C) v 2.9 3.75 Forward voltage (@ 700 mA, 85 °C) 3.05 Forward voltage (@ 1000 mA, 85 °C) 3.15 LeD junction temperature °C 150 relative sPectral Power distribution Relative Spectral Power 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 380 430 480 530 580 630 680 730 780 Relative Radiant Power Wavelength (nm) Cool White Warm White

Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. xlamp xp-e2 leds relative fluX vs. Junction temPerature (if = 350 ma) electrical characteristics (tJ = 85 °c) Relative Flux Output vs. Junction Temperature 20% 40% 60% 80% 100% 120% 25 50 75 100 125 150 Relative Luminous Flux Junction Temperature (ºC) Electrical Characteristics (Tj = 25ºC) 100 200 300 400 500 600 700 800 900 1000 Forward Current (mA) Forward Voltage (V)

Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. xlamp xp-e2 leds thermal desiGn The maximum forward current is determined by the thermal resistance between the LeD junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. relative fluX vs. current (tJ = 85 °c) 200 400 600 800 1000 1200 0 20 40 60 80 100 120 140 Maximum Current (mA) Ambient Temperature (ºC) Rj-a = 10°C/W Rj-a = 15°C/W Rj-a = 20°C/W Rj-a = 25°C/W Relative Intensity vs. Current (Tj = 85ºC) 50% 100% 150% 200% 250% 0 100 200 300 400 500 600 700 800 900 1000 Relative Luminous Flux Forward Current (mA)

Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. xlamp xp-e2 leds relative chromaticity vs. current and temPerature - warm white* * Warm White XLamp Xp-E2 LEDs have a typical CRI of 80. Relative Chromaticity Vs. Current, WW -0.020 -0.015 -0.010 -0.005 0.000 0.005 0.010 0.015 0.020 0 100 200 300 400 500 600 700 800 900 1000 Current (mA) ΔCCx ΔCCy T J = 85 °C Relative Chromaticity Vs. Temperature WW -0.020 -0.015 -0.010 -0.005 0.000 0.005 0.010 0.015 0.020 0 20 40 60 80 100 120 140 160 Tsp (°C) ΔCCx ΔCCy I F = 350 mA

Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. xlamp xp-e2 leds tyPical sPatial distribution Typical Spatial Radiation Pattern 20% 40% 60% 80% 100% -100 -80 -60 -40 -20 0 20 40 60 80 100 Relative Luminous Intensity Angle (°)

Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. xlamp xp-e2 leds reflow solderinG characteristics In testing, Cree has found XLamp Xp-E2 LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all pCB designs and configurations of reflow soldering equipment. Profile Feature lead-based solder lead-free solder Average Ramp-Up Rate (Tsmax to Tp) 3 °C/second max. 3 °C/second max. preheat: Temperature Min (Tsmin) 100 °C 150 °C preheat: Temperature Max (Tsmax) 150 °C 200 °C preheat: Time (tsmin to tsmax) 60-120 seconds 60-180 seconds Time Maintained Above: Temperature (TL) 183 °C 217 °C Time Maintained Above: Time (tL) 60-150 seconds 60-150 seconds peak/Classification Temperature (Tp) 215 °C 260 °C Time Within 5 °C of Actual peak Temperature (tp) 10-30 seconds 20-40 seconds Ramp-Down Rate 6 °C/second max. 6 °C/second max Time 25 °C to Peak Temperature 6 minutes max. 8 minutes max. Note: All temperatures refer to topside of the package, measured on the package body surface.

Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. xlamp xp-e2 leds notes lumen maintenance Projections Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document at www.cree.com/xlamp_app_notes/LM80_results. please read the XLamp Long-Term Lumen Maintenance application note at www.cree.com/xlamp_app_notes/XRE_ lumen_maintenance for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note at www.cree.com/xlamp_app_notes/thermal_management for details on how thermal design, ambient temperature, and drive current affect the LeD junction temperature. moisture sensitivity In testing, Cree has found XLamp Xp-E2 LEDs to have unlimited floor life in conditions ≤ 30 ºC/85% relative humidity (RH). Moisture testing included a 168-hour soak at 85 ºC/85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. Cree recommends keeping XLamp LeDs in their sealed moisture-barrier packaging until immediately prior to use. Cree also recommends returning any unused LeDS to the resealable moisture-barrier bag and closing the bag immediately after use. rohs compliance The levels of environmentally sensitive, persistent biologically toxic (pBT), persistent organic pollutants (pop), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. vision advisory claim WARNING: Do not look at exposed lamp in operation. Eye injury can result. See LED Eye Safety at www.cree.com/ xlamp_app_notes/led_eye_safety.

Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. xlamp xp-e2 leds mechanical dimensions All measurements are ±.13 mm unless otherwise indicated. Anode Anode SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300 Fax (919) 313-5558 Durham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY AND CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE X° ± .5 ° .XXX ± .25 .XX ± .75 .X ± 1.5 FOR SHEET METAL PARTS ONLY .XX ± .25 .XXX ± .125 X° ± .5 ° UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: SURFACE FINISH: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 R1.53 .65 .83 3.30 .50 2.30 3.30 1.30 1/122.000 A2610-00029 OUTLINE DRAWING XPE G2 07/19/12D. CRONIN REVISONS REV DESCRIPTION BY DATE APP'D RECOMMENDED PCB SOLDER PAD RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300 Fax (919) 313-5558 Durham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY AND CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE X° ± .5 ° .XXX ± .25 .XX ± .75 .X ± 1.5 FOR SHEET METAL PARTS ONLY .XX ± .25 .XXX ± .125 X° ± .5 ° UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: SURFACE FINISH: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 R1.53 .65 .83 3.30 .50 2.30 3.30 1.30 1/122.000 A2610-00029 OUTLINE DRAWING XPE G2 07/19/12D. CRONIN REVISONS REV DESCRIPTION BY DATE APP'D RECOMMENDED PCB SOLDER PAD RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300 Fax (919) 313-5558 Durham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY AND CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE X° ± .5 ° .XXX ± .25 .XX ± .75 .X ± 1.5 FOR SHEET METAL PARTS ONLY .XX ± .25 .XXX ± .125 X° ± .5 ° UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: SURFACE FINISH: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 R1.53 .65 .83 3.30 .50 2.30 3.30 1.30 1/122.000 A2610-00029 OUTLINE DRAWING XPE G2 07/19/12D. CRONIN REVISONS REV DESCRIPTION BY DATE APP'D RECOMMENDED PCB SOLDER PAD RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300 Fax (919) 313-5558 Durham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY AND CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE X° ± .5 ° .XXX ± .25 .XX ± .75 .X ± 1.5 FOR SHEET METAL PARTS ONLY .XX ± .25 .XXX ± .125 X° ± .5 ° UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: SURFACE FINISH: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 R1.53 .65 .83 3.30 .50 2.30 3.30 1.30 1/122.000 A2610-00029 OUTLINE DRAWING XPE G2 07/19/12D. CRONIN REVISONS REV DESCRIPTION BY DATE APP'D RECOMMENDED PCB SOLDER PAD RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300 Fax (919) 313-5558 Durham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY AND CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE X° ± .5 ° .XXX ± .25 .XX ± .75 .X ± 1.5 FOR SHEET METAL PARTS ONLY .XX ± .25 .XXX ± .125 X° ± .5 ° UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: SURFACE FINISH: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 R1.53 .65 .83 3.30 .50 2.30 3.30 1.30 1/122.000 A2610-00029 OUTLINE DRAWING XPE G2 07/19/12D. CRONIN REVISONS REV DESCRIPTION BY DATE APP'D RECOMMENDED PCB SOLDER PAD RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING)

Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. xlamp xp-e2 leds taPe and reel All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard. All dimensions in mm. Loaded Pockets (1,000 Lamps) Leader 400mm (min) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) STARTEND Cathode Side Anode Side (denoted by + and circle) 160.0 A A B 2.5±.1 SECTION A-A SCALE 2 : 1 1.5±.1 8.0±.1 4.0±.1 1.75±.10 12.0 .0 +.3 DETAIL B SCALE 2 : 1 13mm Cover Tape Pocket Tape User Feed Direction User Feed Direction SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION X° ± .5 ° .XXX ± .010 .XX ± .03 .X ± .06 FOR SHEET METAL PARTS ONLY .XX ± .01 .XXX ± .005 X° ± .5 ° UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300 Fax (919) 313-5558 Durham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTANED WITHIN ARE THE PROPRIETARY AND CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE SURFACE FINISH: 63 330 +.25 -.75 12.4 +1.0 -.5 MEASURED AT EDGE 16.4 +0.2 MEASURED AT HUB 12.4 +.2 MEASURED AT HUB ±.213.1 1.9±.4 ±.421 60° 60° 1/10.500 A2400-00009 REEL, 13" X 12MM, 3 PIECE SNAP ANTI-STATIC HIPS ---- ---- 09/29/09D. CRONIN 2400-00009 INDEX QTY ITEM COMMENTS 1 1 2400-00009-CORE 2 2 2400-00009-REEL REVISONS REV DESCRIPTION BY DATE APP'D .30 [.012] T Ao 3.7 +/-0.1mm 3.7 +/-0.1mm Bo 2.00 [.079] Po 4.00 [.157] 10.25 [.404] 4.39 [.173] 4.39 [.173] 7.3 ° 12.00 [.472] NOMINAL 12.30 [.484] MAX W 1.75 [.069] 5.50 [.217]F 1.50 [.059] D18.00 [.315] P POCKET SIZE Ao - 3.7mm +/-0.1mm Bo - 3.7mm +/-0.1mm Ko - 2.46mm +0.1/-0mm .30 [.012] T Ao 3.7 +/-0.1mm 3.7 +/-0.1mm Bo 2.00 [.079] Po 4.00 [.157] 10.25 [.404] 4.39 [.173] 4.39 [.173] 7.3 ° 12.00 [.472] NOMINAL 12.30 [.484] MAX W 1.75 [.069] 5.50 [.217]F 1.50 [.059] D18.00 [.315] P POCKET SIZE Ao - 3.7mm +/-0.1mm Bo - 3.7mm +/-0.1mm Ko - 2.46mm +0.1/-0mm .30 [.012] T Ao 3.7 +/-0.1mm 3.7 +/-0.1mm Bo 2.00 [.079] Po 4.00 [.157] 10.25 [.404] 4.39 [.173] 4.39 [.173] 7.3 ° 12.00 [.472] NOMINAL 12.30 [.484] MAX W 1.75 [.069] 5.50 [.217]F 1.50 [.059] D18.00 [.315] P POCKET SIZE Ao - 3.7mm +/-0.1mm Bo - 3.7mm +/-0.1mm Ko - 2.46mm +0.1/-0mm .30 [.012] T Ao 3.7 +/-0.1mm 3.7 +/-0.1mm Bo 2.00 [.079] Po 4.00 [.157] 10.25 [.404] 4.39 [.173] 4.39 [.173] 7.3 ° 12.00 [.472] NOMINAL 12.30 [.484] MAX W 1.75 [.069] 5.50 [.217]F 1.50 [.059] D18.00 [.315] P POCKET SIZE Ao - 3.7mm +/-0.1mm Bo - 3.7mm +/-0.1mm Ko - 2.46mm +0.1/-0mm

Copyright © 2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc. xlamp xp-e2 leds PackaGinG Label with Cree Bin Code, Qty, Lot # Label with Cree Bin Code, Qty, Lot # Vacuum-Sealed Moisture Barrier Bag Dessicant (inside bag) Humidity Indicator Card (inside bag) Patent Label Label with Customer Order Code, Qty, Reel ID, PO #Patent Label Label with Cree Bin Code, Qty, Reel ID Label with Cree Bin Code, Qty, Reel ID Label with Cree Order Code, Qty, Reel ID, PO # Label with Cree Order Code, Qty, Reel ID, PO # Label with Cree Bin Code, Qty, Reel ID Unpackaged Reel Packaged Reel Boxed Reel