XBHAWT-00-0000-0000T60E3

XBHAWT-00-0000-000LT60E1 CREE | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 13

Technical content

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree ® and XLamp ® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. Cree, Inc.

4600 Silicon Drive

Durham, NC 27703 USA Tel: +1.919.313.5300 www.CRee. Com/XLAmp CLD-DS90 Rev 1F Cree® XLamp® XB-H LEDs ProDuCt DEsCriPtion The XLamp ® XB-H LeD delivers a breakthrough combination of lumen output and efficacy in a small package. Delivering more than 500 lumens at 1.5 A, 25 °C in a 2.45 mm 2 package, the Cree XB-H LeD offers triple the lumen density of competing high‑power LEDs to significantly increase the performance of today’s lighting designs. The XB‑H LED joins a new generation of directionally optimized LEDs that offers the industry’s highest optical control factor (OCF), a measurement of how LED size and performance benefit directional lighting applications. High‑OCF LEDs enable lighting manufacturers to improve the performance of any lighting design, create smaller and less expensive systems, and develop new lighting solutions that were previously not possible.

FEAturEs

• Available in white, outdoor white and 80‑, 85‑ and 90‑CRI white
• ANSI‑compatible chromaticity bins
• Binned at 85 °C
• Maximum drive current: 1500 mA
• Low thermal resistance: 4 °C/W
• Wide viewing angle: 110°
• Unlimited floor life at ≤ 30 ºC/85% RH
• Reflow solderable ‑ JEDEC J‑STD‑020C
• Electrically neutral thermal path
• RoHS and REACh compliant
• UL ® recognized component (E349212) tABLE oF ContEnts Relative Flux vs. Junction Relative Chromaticity vs Current and

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. XLamp ® XB-H LED CHArAC tEristiCs Characteristics unit Minimum typical Maximum Thermal resistance, junction to solder point °C/W 4 Viewing angle (FWHM) degrees 110 Temperature coefficient of voltage mV/°C ‑2.2 ESD withstand voltage (HBM per Mil‑Std‑883D) v 8000 DC forward current mA 1500 Reverse voltage v 5 Forward voltage (@ 700 mA, 85 °C) v 2.9 3.3 Forward voltage (@ 1000 mA, 85 °C) v 3.0 Forward voltage (@ 1500 mA, 85 °C) v 3.15 LeD junction temperature °C 150

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. XLamp ® XB-H LED FLuX CHArAC tEristiCs ( tJ = 85 °C) The following table provides several base order codes for XLamp XB‑H LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order‑code nomenclature, please consult the XLamp XB LED Family Binning and Labeling document. Color CCt range Minimum Luminous Flux @ 700 mA Calculated Minimum Luminous Flux (lm)** @ 85 °C order Code Min. Max. Group Flux (lm) @ 85 °C Flux (lm) @ 25 °C* 1.0 A 1.5 A Cool White 5000 K 8300 K T6 280 322 372 499 XBHAWT‑00‑0000‑000L T60E1 T5 260 299 345 463 XBHAWT‑00‑0000‑000L T50E1 T4 240 276 318 428 XBHAWT‑00‑0000‑000L T40E1 T3 220 253 292 392 XBHAWT‑00‑0000‑000L T30E1 Outdoor White 3200 K 5300 K T6 280 322 372 499 XBHAWT‑00‑0000‑0000T60E3 T5 260 299 345 463 XBHAWT‑00‑0000‑0000T50E3 T4 240 276 318 428 XBHAWT‑00‑0000‑0000T40E3 T3 220 253 292 392 XBHAWT‑00‑0000‑0000T30E3 Neutral White 3700 K 5300 K T5 260 299 345 463 XBHAWT‑00‑0000‑000L T50E4 T4 240 276 318 428 XBHAWT‑00‑0000‑000L T40E4 T3 220 253 292 392 XBHAWT‑00‑0000‑000L T30E4 80‑CRI Minimum White 2600 K 4300 K T4 240 276 318 428 XBHAWT‑00‑0000‑000HT40E5 T3 220 253 292 392 XBHAWT‑00‑0000‑000HT30E5 Warm White 2600 K 3700 K T4 240 276 318 428 XBHAWT‑00‑0000‑0000T40E7 T3 220 253 292 392 XBHAWT‑00‑0000‑0000T30E7 T2 200 230 265 356 XBHAWT‑00‑0000‑0000T20E7 85‑CRI Minimum White 2600 K 3200 K T2 200 230 265 356 XBHAWT‑00‑0000‑000PT20E7 S6 182 209 242 324 XBHAWT‑00‑0000‑000PS60E7 S5 172 198 228 306 XBHAWT‑00‑0000‑000PS50E7 90‑CRI Minimum White 2600 K 3200 K S6 182 209 242 324 XBHAWT‑00‑0000‑000US60E7 S5 172 198 228 306 XBHAWT‑00‑0000‑000US50E7 S4 164 186 218 292 XBHAWT‑00‑0000‑000US40E7 Notes:

• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. See the Measurements section (page 9).
• Typical CRI for Cool White (5000 K ‑ 8300 K CCT) is 70.
• Typical CRI for Neutral White (3700 K ‑ 5300 K CCT) is 75.
• Typical CRI for Warm White (2600 K ‑ 3700 K CCT) is 80. * Flux values @ 25 °C are calculated and for reference only. ** Calculated flux values at 1 A and 1.5 A are for reference only.

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. XLamp ® XB-H LED rELAtivE sPEC trAL PowEr DistriBution rELAtivE FLuX vs. JunC tion tEMPErA turE (iF = 700 mA) Relative Spectral Power 20% 40% 60% 80% 100% 380 430 480 530 580 630 680 730 780 Relative Radiant Power Wavelength (nm) Cool White Warm White Relative Flux Output vs. Junction Temperature 20% 40% 60% 80% 100% 120% 25 50 75 100 125 150 Relative Luminous Flux Junction Temperature (ºC)

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. XLamp ® XB-H LED ELEC triCAL CHArAC tEristiCs ( tJ = 85 °C) rELAtivE FLuX vs. CurrEnt ( tJ = 85 °C) Electrical Characteristics (Tj = 25ºC) 300 600 900 1200 1500 2.50 2.75 3.00 3.25 Forward Current (mA) Forward Voltage (V) Relative Intensity vs. Current (Tj = 25ºC) 20% 40% 60% 80% 100% 120% 140% 160% 180% 0 300 600 900 1200 1500 Relative Luminous Flux Forward Current (mA)

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. XLamp ® XB-H LED RelAtive ChRom AtiCity vs CuRRent And tempeRA tuRe (W ARm White*) * Warm White XLamp XB‑H LEDs have a typical CRI of 80. Delta CCT vs. Current -0.006 -0.004 -0.002 0.000 0.002 0.004 0.006 100 300 500 700 900 1100 1300 1500 Current (mA) ΔCCx ΔCCy Delta CCT vs Temp -0.006 -0.004 -0.002 0.000 0.002 0.004 0.006 25 50 75 100 125 150 Tsp (°C) ΔCCx ΔCCy

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. XLamp ® XB-H LED tyPiCAL sPAtiAL DistriBution tHErMAL DEsiGn The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. Typical Spatial Radiation Pattern 20% 40% 60% 80% 100% -90 -60 -30 0 30 60 90 Relative Luminous Intensity Angle (º) Thermal Design 200 400 600 800 1000 1200 1400 1600 0 20 40 60 80 100 120 140 160 Maximum Current (mA) Ambient Temperature (ºC) Rj-a = 10 °C/W Rj-a = 15 °C/W Rj-a = 20 °C/W Rj-a = 25 °C/W

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. XLamp ® XB-H LED rEFLow so LDErinG CHArAC tEristiCs In testing, Cree has found XLamp XB‑H LEDs to be compatible with JEDEC J‑STD‑020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. Profile Feature Lead-Free solder Average Ramp‑Up Rate (Tsmax to Tp) 1.2 °C/second Preheat: Temperature Min (Tsmin) 120 °C Preheat: Temperature Max (Tsmax) 170 °C Preheat: Time (tsmin to tsmax) 65-150 seconds Time Maintained Above: Temperature (TL) 217 °C Time Maintained Above: Time (tL) 45‑90 seconds Peak/Classification Temperature (Tp) 235 ‑ 245 °C Time Within 5 °C of Actual Peak Temperature (tp) 20‑40 seconds Ramp‑Down Rate 1 ‑ 6 °C/second Time 25 °C to Peak Temperature 4 minutes max. Note: All temperatures refer to topside of the package, measured on the package body surface. IPC/JEDEC J‑STD‑020C TP TL Temperature Time t 25˚C to Peak Preheat ts tS tP Ramp-down Ramp-up Critical Zone TL to TP Tsmax Tsmin

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. XLamp ® XB-H LED notEs Measurements The luminous flux, radiant power, chromaticity and CRI measurements in this document are binning specifications only and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors that are not within Cree’s control and are not intended or provided as operational specifications for the products. Calculated values are provided for informational purposes only and are not intended as specifications. pre‑Release Qualification testing Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long‑term reliability for XLamp LEDs and details of Cree’s pre‑release qualification testing for XLamp LEDs. Lumen Maintenance Cree now uses standardized IES LM‑80‑08 and TM‑21‑11 methods for collecting long‑term data and extrapolating LED lumen maintenance. For information on the specific LM‑80 data sets available for this LED, refer to the public LM-80 results document. Please read the Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture sensitivity Cree recommends keeping XLamp LEDs in the provided, resealable moisture‑barrier packaging (MBP) until immediately prior to soldering. Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity. Once the MBP is opened, XLamp XB‑H LEDs may be stored as MSL 1 per JEDEC J‑STD‑033, meaning they have unlimited floor life in conditions of ≤ 30 ºC/85% relative humidity (RH). Regardless of storage condition, Cree recommends sealing any unsoldered LEDs in the original MBP . roHs Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product Documentation sections of www.cree.com. rEACh Compliance REACh substances of very high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA) has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative to insure you get the most up‑to‑date REACh SVHC Declaration. REACh banned substance information (REACh Article 67) is also available upon request.

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. XLamp ® XB-H LED uL® recognized Component Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/ UL 8750. vision Advisory WARNING: Do not look at exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer to the LED Eye Safety application note. notEs - ContinuED

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. XLamp ® XB-H LED MECHAniCAL DiMEnsions Thermal vias, if present, are not shown on these drawings. All measurements are ±.13 mm unless otherwise indicated. SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300Fax (919) 313-5558 4600 Silicon DriveDurham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE FOR SHEET METAL PARTS ONLY UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED: SURFACE FINISH: 1.6 2.45 2.45 R1.53 0.65 2.28 2.29 REF. 2.29 REF. 2.29 0.36 0.33 0.92 2.29 0.92 2.29 0.36 2.29 2.29 2.29 0.39 0.85 0.85 0.25 1.95 0.17 1/131.000 C2610-00038 XBH OUTLINE 11/20/13D. CRONIN REVISONS REV DESCRIPTION BY DATE APP'D RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) RECOMMENDED PCB SOLDER PAD ALTENATIVEPRIMARY ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300Fax (919) 313-5558 4600 Silicon DriveDurham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE FOR SHEET METAL PARTS ONLY UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED: SURFACE FINISH: 1.6 2.45 2.45 R1.53 0.65 2.28 2.29 REF. 2.29 REF. 2.29 0.36 0.33 0.92 2.29 0.92 2.29 0.36 2.29 2.29 2.29 0.39 0.85 0.85 0.25 1.95 0.17 1/131.000 C2610-00038 XBH OUTLINE 11/20/13D. CRONIN REVISONS REV DESCRIPTION BY DATE APP'D RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) RECOMMENDED PCB SOLDER PAD ALTENATIVEPRIMARY ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED top view side view SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300Fax (919) 313-5558 4600 Silicon DriveDurham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE FOR SHEET METAL PARTS ONLY UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED: SURFACE FINISH: 1.6 2.45 2.45 R1.53 0.65 2.28 2.29 REF. 2.29 REF. 2.29 0.36 0.33 0.92 2.29 0.92 2.29 0.36 2.29 2.29 2.29 0.39 0.85 0.85 0.25 1.95 0.17 1/131.000 C2610-00038 XBH OUTLINE 11/20/13D. CRONIN REVISONS REV DESCRIPTION BY DATE APP'D RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) RECOMMENDED PCB SOLDER PAD ALTENATIVEPRIMARY ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED Bottom view SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300Fax (919) 313-5558 4600 Silicon DriveDurham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE FOR SHEET METAL PARTS ONLY UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED: SURFACE FINISH: 1.6 2.45 2.45 R1.53 0.65 2.28 2.29 REF. 2.29 REF. 2.29 0.36 0.33 0.92 2.29 0.92 2.29 0.36 2.29 2.29 2.29 0.39 0.85 0.85 0.25 1.95 0.17 1/131.000 C2610-00038 XBH OUTLINE 11/20/13D. CRONIN REVISONS REV DESCRIPTION BY DATE APP'D RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) RECOMMENDED PCB SOLDER PAD ALTENATIVEPRIMARY ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED Alternate Bottom view Anode Anode SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300Fax (919) 313-5558 4600 Silicon DriveDurham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE FOR SHEET METAL PARTS ONLY UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED: SURFACE FINISH: 1.6 2.45 2.45 R1.53 0.65 2.28 2.29 REF. 2.29 REF. 2.29 0.36 0.33 0.92 2.29 0.92 2.29 0.36 2.29 2.29 2.29 0.39 0.85 0.85 0.25 1.95 0.17 1/131.000 C2610-00038 XBH OUTLINE 11/20/13D. CRONIN REVISONS REV DESCRIPTION BY DATE APP'D RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) RECOMMENDED PCB SOLDER PAD ALTENATIVEPRIMARY ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300Fax (919) 313-5558 4600 Silicon DriveDurham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE FOR SHEET METAL PARTS ONLY UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED: SURFACE FINISH: 1.6 2.45 2.45 R1.53 0.65 2.28 2.29 REF. 2.29 REF. 2.29 0.36 0.33 0.92 2.29 0.92 2.29 0.36 2.29 2.29 2.29 0.39 0.85 0.85 0.25 1.95 0.17 1/131.000 C2610-00038 XBH OUTLINE 11/20/13D. CRONIN REVISONS REV DESCRIPTION BY DATE APP'D RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) RECOMMENDED PCB SOLDER PAD ALTENATIVEPRIMARY ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED recommended PCB solder Pad recommended stencil Pattern (hatched Area is opening)

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. XLamp ® XB-H LED tAPE AnD rEEL All Cree carrier tapes conform to EIA‑481D, Automated Component Handling Systems Standard. Except as noted, all dimensions in mm. SIZE TITLE OF REV. SHEET C DRAWING NO. DATE DATE DATE CHECK FINAL PROTECTIVE FINISH MATERIAL APPROVED DRAWN BY THIRD ANGLE PROJECTION SCALE A B C D 123456 6 5 4 3 2 1 A B C D Phone (919) 313-5300 Fax (919) 313-5558 Durham, N.C 27703 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY AND CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION OF CREE INC. NOTICE X° ± .5 ° .XXX ± .25 .XX ± .75 .X ± 1.5 FOR SHEET METAL PARTS ONLY .XX ± .25 .XXX ± .125 X° ± .5 ° UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: SURFACE FINISH: 1.6 BB 8.00 ±.10 4.00 ±.10 2.00 ±.10 +.10/-.001.50 ± .101.00 .30 ± .10

12.00 Nominal

12.30 Max

5.50 ±.10 1.75 ±.10 10.25 ±.10 2.60+/-0.1mm 2.05 +/-0.1 2.60 +/-0.1 REVISONS REV DESCRIPTION BY DATE APP'D A Released DC 10/23/11 JL B ADDED CATHODE AND ANODE NOTE DC 2/26/12 C CHANGED POCKET DIMS AND TOLERANCES DC 8/3/12 1/14.000 C2402-00020 Carrier Tape, 2525 HEW 10/23/11D. CRONIN Notes: 1. 10 sprocket hole pitch cumulative tolerance ± 0.2mm REFERENCE VENDOR PART NUMBER 020246 CATHODE SIDE ANODE SIDE B-BSECTION Loaded Pockets (1,000 Lamps) Leader 400mm (min) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) STARTEND Cathode Side Anode Side (denoted by + and circle) 160.0 A A B 2.5±.1 SECTION A-A SCALE 2 : 1 1.5±.1 8.0±.1 4.0±.1 1.75±.10 12.0 .0 +.3 DETAIL B SCALE 2 : 1 13mm Cover Tape Pocket Tape User Feed Direction User Feed Direction

Copyright © 2014-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC. XLamp ® XB-H LED PACkAGinG Patent Label (on bottom of box) Label with Cree Bin Code, Quantity, Reel ID Label with Cree Bin Code, Quantity, Reel ID Label with Cree Order Code, Quantity, Reel ID, PO # Label with Cree Order Code, Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Unpackaged Reel Packaged Reel Boxed Reel CREE Bin Code & Barcode Label Vacuum-Sealed Moisture Barrier Bag Label with Customer P/N, Qty, Lot #, PO # Label with Cree Bin Code, Qty, Lot # Label with Cree Bin Code, Qty, Lot # Vacuum-Sealed Moisture Barrier Bag Patent Label Label with Customer Order Code, Qty, Reel ID, PO #