WRPP MSYSTEM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

MODEL: WRPP WRPP SPECIFICATIONS ES-2222 Rev.3 Page 1/4 http://www.m-system.co.jp/ Dual Output Plug-in Signal Conditioners W-UNIT ENCODER SIGNAL DISTRIBUTOR (rotary encoder use) Functions & Features

  • Isolating two phase pulse input signals from a rotary encoder and distributing them to two outputs (input frequency = output frequency)
  • Various outputs (open collector, voltage pulse, RS-422 line driver pulse)
  • Can be used as a pulse isolator of two different I/O specs
  • Converting RS-422 line driver pulse into an open collector pulse
  • Isolation up to 2000 V AC
  • Maximum frequency of 1 MHz (2.83) (3.15) 136 (5.35) mm (inch) MODEL: WRPP–[1][2][3][4]-[5][6]

ORDERING INFORMATION

  • Code number: WRPP-[1][2][3][4]-[5][6] Specify a code from below for each of [1] through [6]. (e.g. WRPP-JJJN-R/Q)
  • Specify the specification for option code /Q (e.g. /C01/S01) [1] INPUT A1: Dry contact K: 3.3 V pulse C: 5 V pulse D: 12 V/24 V pulse J: RS-422 line driver pulse [2] OUTPUT 1 A: Open collector (max. frequency 100 kHz) K: 3.3 V pulse (max. frequency 1 MHz) M: 5 V pulse (max. frequency 500 kHz) N: 12 V pulse (max. frequency 100 kHz) J: RS-422 line driver pulse (max. frequency 1 MHz) [3] OUTPUT 2 A: Open collector (max. frequency 100 kHz) K: 3.3 V pulse (max. frequency 1 MHz) M: 5 V pulse (max. frequency 500 kHz) N: 12 V pulse (max. frequency 100 kHz) J: RS-422 line driver pulse (max. frequency 1 MHz) [4] OUTPUT LOGIC (both Input 1 & 2) N: The same as the input R: Inverted [5] POWER INPUT AC Power M2: 100 – 240 V AC (Operational voltage range 85 – 264 V, 47 – 66 Hz) DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) R2: 11 – 27 V DC (Operational voltage range 11 – 27 V, ripple 10 %p-p max.) (CE not available) P: 110 V DC (Operational voltage range 85 – 150 V, ripple 10 %p-p max.) [6] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q (multiple selections) COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating TERMINAL SCREW MATERIAL /S01: Stainless steel GENERAL SPECIFICATIONS Construction: Plug-in Connection: M3.5 screw terminals Screw terminal: Chromated steel (standard) or stainless steel Housing material: Flame-resistant resin (black) Isolation: Input to output 1 to output 2 to power Input monitor LED: Available to check input pulse existence Input pulse sensing: DC coupled

MODEL: WRPP WRPP SPECIFICATIONS ES-2222 Rev.3 Page 2/4 http://www.m-system.co.jp/ INPUT SPECIFICATIONS ■ Dry Contact Max. frequency: 100 kHz Input requirements Sensing: 5 V DC / 10 mA Detecting level: OFF: ≥ 3.0 V / ≥ 750 Ω ON: ≤ 2.0 V / ≤ 333 Ω Sensing voltage/current shows the excitation supply to the input terminal and the current value at the time of shortcircuit. Detecting level shows the threshold used to determine ON or OFF status of the pulses and the resistance values of the dry contact of that time. ■ Voltage Pulse Waveform: Square or sine

  • 3.3 V Pulse Max. frequency: 1 MHz Input impedance: Approx. 8 kΩ 100 pF Max. voltage between terminals (pulse): -10 – +15 V Max. voltage between terminals (DC): -5 – +10 V DC Detecting level: VH ≥ 2.0 V, VL ≤ 1.3 V
  • 5 V Pulse Max. frequency: 500 kHz Input impedance: Approx. 14 kΩ 100 pF Max. voltage between terminals (pulse): -10 – +15 V Max. voltage between terminals (DC): -5 – +10 V DC Detecting level: VH ≥ 3.0 V, VL ≤ 2.0 V
  • 12 V, 24 V Pulse Max. frequency: 100 kHz Input impedance: Approx. 20 kΩ Max. voltage between terminals (pulse): -30 – +50 V Max. voltage between terminals (DC): -30 – +50 V DC Detecting level: VH ≥ 7.0 V, VL ≤ 5.0 V ■ RS-422 Line Driver Pulse Maximum frequency: 1 MHz Receiver: Conforms to RS-422 (No receiving resistor incorporated) OUTPUT SPECIFICATIONS ■ Open collector Max. frequency: 100 kHz Rating: 50 V DC @ 100 mA Saturation voltage: 0.12 V DC ■ Voltage Pulse: Rating (3.3, 5 or 12 V) ±20 % Max. frequency ; Load resistance (the lower value of either this or the maximum frequency of the input signal)

3.3 V 1 MHz ; 660 Ω

5 V 500 kHz ; 1 kΩ

12 V 100kHz ; 2.4 kΩ Low level: ≤ 0.5 V ■ RS-422 Line Driver Pulse: Conforms to RS-422 Max. frequency: 1 MHz Output current: ±20 mA INSTALLATION Power Consumption

  • AC: Approx. 4 VA at 100 V Approx. 5 VA at 200 V Approx. 6 VA at 240 V
  • DC: Approx. 3 W Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Surface or DIN rail Weight: 250 g (0.55 lb) PERFORMANCE Response time delay
  • 3.3 or 5 V voltage pulse or RS-422 line driver pulse: Approx. 0.15 - 0.5 μsec.
  • 12 V voltage pulse or open collector: 0.2 - 2 μsec. Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 2000 V AC @1 minute (input to output 1 to output 2 to power to ground) STANDARDS & APPROVALS EU conformity: EMC Directive EMI EN 61000-6-4 EMS EN 61000-6-2 Low Voltage Directive EN 61010-1 Installation Category II Pollution Degree 2 Input or output 1 or output 2 to power input: Reinforced insulation (300 V) Input to output 1 to output 2: Basic insulation (300 V) RoHS Directive EN 50581

MODEL: WRPP WRPP SPECIFICATIONS ES-2222 Rev.3 Page 3/4 http://www.m-system.co.jp/ EXTERNAL VIEW *OQVU.POJUPS-&%1IBTF# 3FE *OQVU.POJUPS-&%1IBTF" (SFFO OUTPUT LOGIC Applicable for both Output 1 and 2. H L Voltage pulse or RS-422 line driver pulse Output Non-inverted Non-inverted Dry contactInput H L H L OFF ON H L Inverted Inverted H L OFF ON OFF ON OFF ON OFF ON Open collector Voltage pulse RS-422 line driver pulse EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch) 80 (3.15) 50 (1.97) 72 (2.83) 107 (4.21) 80 (3.15) (.79) 60 (2.36) 72 (2.83) 7.8 (.31) CLAMP (top & bottom) DIN RAIL 35mm wide2–4.5 (.18) dia. MTG HOLE 25 (.98) deep 14–M3.5 SCREW

  • When mounting, no extra space is needed between units. 12 5614 11 110 15

MODEL: WRPP WRPP SPECIFICATIONS ES-2222 Rev.3 Page 4/4 http://www.m-system.co.jp/ SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Input Connection Examples Output Connection Examples Base Socket Output Circuit Phase A Output Circuit Phase B Output Circuit Phase A 500Ω ■ Dry Contact Input ■ Open Collector Output ■ Voltage Pulse Output■ Open Collector Output ■ RS-422 Line Driver Pulse Output PHASE A INPUT OUTPUT 1 OUTPUT 2 PHASE B U (+) V (−) POWER Input Circuit Input Circuit Output Circuit Phase B RS-422 Receiver RS-422 Receiver Phase A Phase A Phase B Phase B −Rotary Encoder Isolation PHASE A PHASE A PHASE B PHASE B ■ Voltage Pulse Input ■ RS-422 Line Driver Pulse Input Specifications are subject to change without notice.