WL2205-L RFHIC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Korean Facilities : 82-31-250-5078 / rfsales@rfhic.com All specifications may change without notice US Facility : 919-677-8780 / sales@rfhicusa.com 1 / 4 Version 1.0 Product Features Applications

  • E-pHEMT chip on board
  • No matching circuit needed
  • 30 ~ 2200MHz Wideband Amplifier
  • Higher linearity
  • Surface Mount Hybrid package
  • CP-16A Tape & Reel Package
  • Pb Free / RoHS Standard
  • CATV
  • Radio systems
  • Satellite
  • RF Sub-Systems

Description

RFHIC’s Low Noise Amplifier series are all hybrid LNA type products which includes all matching for the convenience of customers. WL series are a wideband LNA used for up to 4GHz. All LNA h ybrids are possible to have custom frequency & spec without any additional NRE cost involved. Electrical Specifications PARAMETER UNIT MIN TYP MAX CONDITION Operating Frequency MHz 30 - 2200 - Gain dB 13 15.5 - - Gain Flatness dB - 1.2 1.5 30 ~ 2200MHz Input Return Loss dB - -15 - - Output Return Loss dB - -20 - - 1dB Compression Point dBm 13 17 - 30 ~ 2200MHz Output IP3 dBm - 30 - 30 ~ 1000MHz - 26 - 1000 ~ 2200MHz Noise Figure dB - 1.4 - 30 ~ 1000MHz - 1.7 - 1000 ~ 2200MHz DC Current mA - 50 - Vdd = 5.0V Note 1. Test conditions unless otherwise noted. Test Freq = 1-500MHz, T=25℃, Vdd=5V , 50Ω system 2. OIP3 measured with 2 tones at an output power of +5dBm/tone separated by 1MHz, Test Freq = 30 and 2200MHz Absolute Maximum Ratings PARAMETER UNIT MIN TYP MAX CONDITION Supply Voltage VDC - 5 9 - Operating Temperature ℃ -40 - 85 - Storage Temperature ℃ -50 - 125 - Package Type : CP-16A

Korean Facilities : 82-31-250-5078 / rfsales@rfhic.com All specifications may change without notice US Facility : 919-677-8780 / sales@rfhicusa.com 2 / 4 Version 1.0 Typical Performance @ VDD=5V , IDS=50mA, T=25℃, 50ohm System S-Parameter Frequency vs. Noise Figure -10 -20 -10 -30 Freq(GHz) Return Loss(dB) Gain(dB) 30 400 800 1200 1600 2000 Freq(MHz) NF(dB) Frequency vs. P1dB Frequency vs. OIP3 30 400 800 1200 1600 2000 Freq(MHz) P1dB(dBm) 30 400 800 1200 1600 2000 Freq(MHz) OIP3(dBm) Block Diagram Note 1. WL Series Have internal DC blocking capacitors at the RF input and output ports. S21 S22 S11

Korean Facilities : 82-31-250-5078 / rfsales@rfhic.com All specifications may change without notice US Facility : 919-677-8780 / sales@rfhicusa.com 3 / 4 Version 1.0 Package Dimensions (Type: CP-16A) * Unit: mm[inch] | Tolerance ±0.15[.006] ▲ T o p V i e w ▲ S i d e V i e w ▲ Bottom View Pin Description Pin No Function Pin No Function

1 GND 4 GND

2 Input 5 Output

3 GND 6 Vcc

Recommended Pattern Evaluation board Layout * Mounting Configuration Notes 1. Ground / thermal via holes are critical for the proper performance of this device. 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via hole region contacts the heatsink. 4. Do not put solder mask on the backside of the PCB in the region where the board contacts the heatsink. 5. RF trace width depends upon the PCB material and construction. 6. Use 1 oz. Copper minimum.

Korean Facilities : 82-31-250-5078 / rfsales@rfhic.com All specifications may change without notice US Facility : 919-677-8780 / sales@rfhicusa.com 4 / 4 Version 1.0

Revision History

Part Number Release Date Version Modification Data Sheet Status WL2205-L 20121010 1.0 - - RFHIC Corporation reserves the right to make changes to any products herein or to discontinue any product at any time without notice. While product specifications have been thoroughly examined for reliability, RFHIC Corporation strongly recommends buyers to verify that the information they are using is accurate before ordering. RFHIC Corporation does not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including wi thout limitation consequential or incidental damages. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expect ed to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC Corporation and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such unauthorized use. Sales, inquiries and support should be directed to the local authorized geographic distributor for RFHIC Corporation. For customers in the US, please contact the US Sales Team at 919- 677-8780. For all other inquiries, please contact the International Sales Team at 82-31-250-5078.