VP603 SANYO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
- Three-channel video output circuit for CRT displays
- Optimal for monitors that require f VIDEO ‡
70 MHz, 17-inch fH ‡ 64 kHz
unit: mm 2117 Wideband Output Module (Video Pack) 13097HA(OT) No. 5542-1/8 [VP603] SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN CRT Display Video Output Amplifier: High-Voltage, Wideband Amplification VP603 Parameter Symbol Conditions Ratings Unit Maximum supply voltage VCC max 90 V VBB max 15 V Allowable power dissipation Pd max At Tc = 25°C with an ideal heat sink 25 W Junction temperature Tj max 150 °C Case temperature Tc max 100 °C Storage temperature Tstg –20 to +110 °C Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit Recommended supply voltage I VCC 70 V VBB 10 V Recommended supply voltage II VCC 80 V VBB 10 V Operating Conditions at Ta = 25°C
No. 5542-2/8 VP603 Parameter Symbol Conditions Ratings Unit min typ max Bandwidth I (–3 dB) fc VCC = 70 V, VBB = 10 V, CL = 5 pF, 75 MHzVIN (DC) = 2.5 V, VOUT (p-p) = 40 V Bandwidth II (–3 dB) fc VCC = 80 V, VBB = 10 V, CL = 5 pF, 70 MHzVIN (DC) = 2.7 V, VOUT (p-p) = 50 V Pulse response characteristics tr VCC = 80 V, VBB = 10 V, CL = 5 pF, 5.2 ns tf VIN (DC) = 2.7 V, VOUT (p-p) = 40 V 5.0 ns Voltage gain G V (DC) 17 19 21 ICC 1 VCC = 70 V, VBB = 10 V, VIN (DC) = 2.3 V, 27 mA Current drain I f = 10 MHz clock, CL = 5 pF, VOUT (p-p) = 40 V ICC 2 VCC = 70 V, VBB = 10 V, VIN (DC) = 2.3 V, 40 mAf = 70 MHz clock, CL = 5 pF, VOUT (p-p) = 40 V ICC 1 VCC = 80 V, VBB = 10 V, VIN (DC) = 2.6 V, 32 mA Current drain II f = 10 MHz clock, CL = 5 pF, VOUT (p-p) = 50 V ICC 2 VCC = 80 V, VBB = 10 V, VIN (DC) = 2.6 V, 47 mAf = 70 MHz clock, CL = 5 pF, VOUT (p-p) = 50 V Electrical Characteristics at Ta = 25°C Internal Equivalent Circuit
No. 5542-3/8 VP603
Sample Application Circuit 1. Mounting in the CRT neck Note: * This RC matching circuit is provided to match the IC internal impedance with the output load impedance. When the IC is mounted in the CRT neck, this circuit can be removed if the total CL (load capacitance) is under 10 pF. 2. Cable transmission (separate boards) Mounting location for the C, G matching circuit Add the RC matching circuit at a position as close as possible to the VP603 output pin. Thermal Design for the VP603 Since the VP603 is a three-channel device, we first consider a single channel. The chip temperature of each transistor during actual operation is determined using the following formula. qj-c (Tri): Thermal resistance of an individual transistor Pc (Tri): Collector loss for an individual transistor ∆Tc: Case temperature rise Ta: Ambient temperature No. 5542-4/8 VP603
The qj-c(Tri) for each chip is: Although the loss for each transistor in a V ideo Pack varies with frequency and is not uniform, if we assume that the maximum operating frequency, f = 70 MHz (clock), then the chips with the largest loss will be transistors 3 and 4 and that loss will be about 1/4 of the total loss.Thus from the Pd for a single channel we have: Here, we must select a heat sink with a capacity qh such that the Tj of these transistors does not exceed 150°C. Equation (4) below gives the relationship between qh and ∆Tc. The required qh is calculated using this equation and equation (1). VP603 Thermal Design Example Conditions: Using an f H = 70 kHz class monitor, fv = 100 MHz (clock) V CC = 80 V, VBB = 10 V, VOUT = 50 Vp-p (CL = 10 pF) Since this class of monitor can be operated up to Ta = 60°C, here we consider the case where the maximum clock frequency is 100 MHz. As mentioned previously, the chip with the largest loss is transistor Tr3/Tr4. Determining the value gives: We determine ∆Tj by substituting the value for qj-c in equation (5). Here, Tc(max) (measured at the package surface) is taken to be under 100°C. This means that it suffices to design the heat sink taking Tc(max) < 100°C as the design target to fulfill the conditions that Tj(max) < 150°C and furthermore that Tc(max) < 100°C; qh = ∆Tc ÷ Pd (TOTAL) = (Tc – Ta) ÷ [Pd (1CH) · 3] No. 5542-5/8 VP603
Thus the thermal resistance in this case is qh = 3.1°C/W. In actual practice, the ambient temperature and operating conditions will allow a heat sink smaller than that indicated by this calculation to be used. Therefore, design optimization taking the actual conditions into account is also required. Surge Protection Surge protection is required when this device is connected to a CRT. This product requires the same protection as earlier products. 1. Termination spark gap 2. Surge suppression resistor (Recommended value: 33 to 68 Ω ) 3. Surge suppression diode (Installed in the vicinity of the IC output pin.) Note: The value of surge suppression resistors must be determined taking both the stipulated discharge test and the required frequency bandwidth into account. No. 5542-6/8 VP603
Mounting notes: Since the specified heat sink is required to operate a mounted V ideo Pack, we recommend the following mounting technique. (See the thermal design item for details on the required heat sink.) In particular, since the package used for this product is even more compact than that used in the earlier VPS series, the following points require special care. (These are recommendations.) 1. A tightening torque of between 0.39 and 0.88 N-m is recommended. 2. The bolt hole spacing in the heat sink should match that of the IC. In particular, the bolt hole spacing should be pulled in to be as close as possible, within the range that mounting is possible, to the dimensions A and B in the package dimensions drawing, as shown below. 3. Use either the truss screws (truss bolts) or binding screws stipulated in the JIS standards as the mounting bolts. Also, use washers to protect the IC case. 4. Foreign matter, such as machining chips, must not be left trapped between the IC case and the heat sink. If grease is applied to the junction surface, be sure to apply the grease evenly. 5. Solder the IC leads to the printed circuit board after mounting the heat sink to the IC. Note: The heat sink is absolutely required to operate this V ideo Pack. Never, in any situation, apply power to a V ideo Pack as an independent device. The V ideo Pack may be destroyed. No. 5542-7/8 VP603
No. 5542-8/8 VP603 Peripheral wiring and ground leading: When shipped, the VP603 product lead pins have standard support for forming (zigzag) so that the distance between pins will be 2.54 mm. Also, the pin layout is standardized to the I/O and power supply line arrangement shown below. IC Surrounding Pin Layout (Top view) Note: Design applications that use two-sided printed circuit boards or similar technologies so that input and output lines do not cross. Crossed lines can lead to increased crosstalk. Also, lines should be kept as short as possible, and lines in the ground pattern should be made as wide as possible. These layout design principles will minimize bandwidth degradation and oscillation. This catalog provides information as of August, 1997. Specifications and information herein are subject to change without notice. n No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. n Anyone purchasing any products described or contained herein for an above-mentioned use shall: À Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: \` Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. n Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.