VHD6031035AA PLETRONICS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

Product information is current as of publication date. The product conforms Copyright © 2008, Pletronics Inc. to specifications per the terms of the Pletronics standard warranty. Production processing does not necessarily include testing of all parameters. VHD6 Series 3.3V VCXO CMOS Oscillator December 2008

  • Pletronics’ VHD6 Series is a voltage controlled crystal oscillator with a CMOS output.
  • This model uses fundamental mode crystals with no multiplication circuits.
  • Tape and Reel or tube packaging is available.
  • 10 to 108 MHZ
  • 3.2 x 5 mm Ceramic LCC Package
  • Voltage Control Function on pad 1
  • Enable/ Disable Function on pad 2 Pletronics Inc. certifies this device is in accordance with the RoHS 6/6 (2002/95/EC) and WEEE (2002/96/EC) directives. Pletronics Inc. guarantees the device does not contain the following: Cadmium, Hexavalent Chromium, Lead, Mercury, PBB’s, PBDE’s Weight of the Device: 0.09 grams Moisture Sensitivity Level: 1 As defined in J-STD-020C Second Level Interconnect code: e4 Absolute Maximum Ratings: Parameter Unit VCC Supply Voltage -0.5V to +5.5V Vi Input Voltage -0.5V to V CC + 0.5V Vo Output Voltage -0.5V to V CC + 0.5V Thermal Characteristics The maximum die or junction temperature is 155oC The thermal resistance junction to board is 60 to 100oC/Watt depending on the solder pads, ground plane and construction of the PCB.

VHD6 Series 3.3V VCXO CMOS Oscillator December 2008 www.pletronics.com 425-776-1880 2 Part Number: VHD6031035 E G 500 100 -16.384M -XX Internal code or blank Nominal Frequency in MHZ Pullability in ppm (Vcontrol) 050 = +_ 50 ppm minimum 100 = +_ 100 ppm minimum Stability in ppm 000 = APR 500 = +_ 50 ppm 250 = +_ 25 ppm Highest Specified Operating Temperature A = +40oC F = +65oC L = +90oC B = +45oC G = +70oC M = +95oC C = +50oC H = +75oC N = +100oC D = +55oC J = +80oC P = +105oC E = +60oC K = +85oC Lowest Specified Operating Temperature A = +10oC E = -10oC J = -30oC B = +5oC F = -15oC K = -35oC C = +0oC G = -20oC L = -40oC D = -5oC H = -25oC M = -45oC Series (Part Type, Logic & Package) Part Marking: PLE VHD6 FF.FFFM C YMDXX Legend: P or PLE = Pletronics FF.FFFM = Frequency in MHZ YMD = Date of Manufacture xx = Internal factory codes Specifications such as frequency stability, supply voltage and operating temperature range, etc. are not identified from the marking. External packaging labels and packing list will correctly identify the ordered Pletronics part number. Codes for Date Code YMD Code 8 9 0 1 2 3 4 Year 2008 2009 2010 2011 2012 2013 2014 Code A B C D E F G H J K L M Month JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC C o d e 123456789ABC D a y 123456789 1 0 1 1 1 2 Code D E F G H J K L M N P R D a y 1 31 41 51 61 71 81 92 02 12 22 32 4 Code T U V W X Y Z D a y 2 52 62 72 82 93 03 1

VHD6 Series 3.3V VCXO CMOS Oscillator December 2008 www.pletronics.com 425-776-1880 3 Electrical Specification for 3.30V +_5% over the specified temperature range Item Min Typ Max Unit Condition Frequency Range 10 - 108 MHZ Frequency Accuracy 1 + _25 - - ppm Not specified if APR is specified Pullability 1 +_90 - + _125 ppm For Vcontrol 1.65 V + _1.5 V. Not specified if APR is specified Defined by the part number Pullability (APR) 1 + _50 - - ppm Absolute Pull Range, includes the effect of temperature stability Defined by the part number Output Waveform CMOS Output High Level 90 - - % of V CC for IOH= +7 mA Output Low Level - - 10 % of V CC for IOL = -7 mA Output TRISE and TFALL - 3.0 6.0 nS 10% to 90% of V CC, CLOAD = 15 pF Output Symmetry 45 50 55 % at 50% point of V CC (See load circuit) Vcontrol Resistance Pin 1 20 25 - Kohm Modulation Bandwidth 10 20 - KHz Vcontrol = 1.65V + _1.65V, -3dB Integrated Jitter - 0.4 0.6 pS 12 KHz to 20 MHZ E/D Internal Pull-up 50 - - Kohm to V CC V disable - - 15 % of V CC applied to pin 1 V enable 85 - - % of V CC applied to pin 1 Output leakage VOUT = VCC -10 - +10 uA Pin 1 low, device disabled VOUT = 0V -10 - +10 uA Enable time - - 250 nS Time for output to reach a logic state Disable time - - 250 nS Time for output to reach a high Z state Start up time - 1.5 10 mS Time for output to reach specified frequency Supply Current - 5.0 8.0 mA C LOAD = 15 pF Operating Temperature -45 +105 oC Defined by part number Storage Temperature Range -55 +125 oC Specifications with Pad 2 E/D open circuit 1For all supply voltages, load changes, aging for 1 year, shock, vibration and temperatures.

VHD6 Series 3.3V VCXO CMOS Oscillator December 2008 www.pletronics.com 425-776-1880 4 Load Circuit and Test Waveform Reliability: Environmental Compliance Parameter Condition Mechanical Shock MIL-STD-883 Method 2002, Condition B Vibration MIL-STD-883 Method 2007, Condition A Solderability MIL-STD-883 Method 2003 Thermal Shock MIL-STD-883 Method 1011, Condition A ESD Rating Model Minimum Voltage Conditions Human Body Model 1500 MIL-STD-883 Method 3115 Charged Device Model 1000 JESD 22-C101 Package Labeling Font is Courier New Font is Arial Bar code is 39-Full ASCII (example actual PN will appear) Trise 10% * Vcc Ground Vlow 50% * Vcc 90% * Vcc Vhigh Tfall Symmetry

VHD6 Series 3.3V VCXO CMOS Oscillator December 2008 www.pletronics.com 425-776-1880 5 3 4 Mechanical: Inches mm C 0.053 max 1.35 max D 1 0.050 1.27 E1 0.050 1.27 F1 0.004 0.10 G1 0.039 1.00 H1 0.025 0.63 Contacts: Gold 11.8 µinches 0.3 µm minimum over Nickel 50 to 350 µinches 1.27 to 8.89 µm

1 Typical dimensions

I1 0.020 0.50 J1 0.004R 0.10R K1 0.008R 0.20R Pad Function Note

1 Vcontrol Input

2 Output

When this pad is not connected, the oscillator shall operate When this pad is logic low, the output will be inhibited (high impedance state) Recommend connecting this pad to Vcc if the oscillator is to be always on

3 Ground (GND)

4 Output

5 N.C. No Internal connection, pad may be connected to ground or V CC

6 Supply Voltage

(VCC) Recommend connecting appropriate power supply bypass capacitors as close as possible. Layout and application information For Optimum Jitter Performance, Pletronics recommends:

  • a ground plane under the device
  • no large transient signals (both current and voltage) should be routed under the device do not layout near a large magnetic field such as a high frequency switching power supply
  • do not place near piezoelectric buzzers or mechanical fans.

VHD6 Series 3.3V VCXO CMOS Oscillator December 2008 www.pletronics.com 425-776-1880 6 260°C Maximum

10 Seconds Maximum

215°C±10°C Approximately 50 Seconds Allowed rate of temperature change Maximum 4°C per second 120 to 160 Seconds 100 150 200 250 Temperature (°C) 175°C±10°C Reflow Cycle (typical for lead free processing) The part may be reflowed 2 times without degradation. Tape and Reel: available for quantities of 250 to 1000 per reel Constant Dimensions Table 1 Tape Size D0 D1 Min E1 P0 P2 S1 Min T Max Max 8mm 1.5 +0.1 -0.0 1.0 1.75 +_0.1 4.0 +_0.1 2.0 +_0.05 0.6 0.6 0.1 12mm 1.5 16mm 1.5 2.0 +_0.1 24mm 1.5 Variable Dimensions Table 2 Tape Size Max E2 Min F P1 T2 Max W Max Ao, Bo & Ko Note 1: Embossed cavity to conform to EIA-481-B Dimensions in mm Not to scale REEL DIMENSIONS A inches 7.0 10.0 13.0 mm 177.8 254.0 330.2 B inches 2.50 4.00 3.75 mm 63.5 101.6 95.3 Tape Width D mm 16.4 +2.0 -0.0 16.4 +2.0 -0.0 16.4 +2.0 -0.0 16.0 Reel dimensions may vary from the above

VHD6 Series 3.3V VCXO CMOS Oscillator December 2008 www.pletronics.com 425-776-1880 7 IMPORTANT NOTICE Pletronics Incorporated (PLE) reserves the right to make corrections, improvements, modifications and other changes to this product at anytime. PLE reserves the right to discontinue any product or service without notice. Customers are responsible for obtaining the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to PLE’s terms and conditions of sale supplied at the time of order acknowledgment. PLE warrants performance of this product to the specifications applicable at the time of sale in accordance with PLE’s limited warranty. Testing and other quality control techniques are used to the extent PLE deems necessary to support this warranty. Except where mandated by specific contractual documents, testing of all parameters of each product is not necessarily performed. PLE assumes no liability for application assistance or customer product design. Customers are responsible for their products and applications using PLE components. To minimize the risks associated with the customer products and applications, customers should provide adequate design and operating safeguards. PLE products are not designed, intended, authorized or warranted to be suitable for use in life support applications, devices or systems or other critical applications that may involve potential risks of death, personal injury or severe property or environmental damage. Inclusion of PLE products in such applications is understood to be fully at the risk of the customer. Use of PLE products in such applications requires the written approval of an appropriate PLE officer. Questions concerning potential risk applications should be directed to PLE. PLE does not warrant or represent that any license, either express or implied, is granted under any PLE patent right, copyright, artwork or other intellectual property right relating to any combination, machine or process which PLE product or services are used. Information published by PLE regarding third-party products or services does not constitute a license from PLE to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from PLE under the patents or other intellectual property of PLE. Reproduction of information in PLE data sheets or web site is permissible only if the reproduction is without alteration and is accompanied by associated warranties, conditions, limitations and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. PLE is not responsible or liable for such altered documents. Resale of PLE products or services with statements different from or beyond the parameters stated by PLE for that product or service voids all express and implied warranties for the associated PLE product or service and is an unfair or deceptive business practice. PLE is not responsible for any such statements. Contacting Pletronics Inc. Pletronics Inc. Tel: 425-776-1880 19013 36 th Ave. West Fax: 425-776-2760 Lynnwood, WA 98036-5761 USA E-mail: ple-sales@pletronics.com URL: www.pletronics.com Copyright © 2008, Pletronics Inc.