VCXO-5030-EAE-S

VCXO-5030-DAE-H VECTRON | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

Voltage Controlled Crystal Oscillator Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Small 14mm x 9mm • Low phase noise • Frequency Range: 1 MHZ to 800 MHZ • Previous Model: J-Type • Clock Smoothing • Frequency Translation • SONET, SDH, ATM, DSLAM, ADM • Features Applications VX-503 The VX-503 voltage controlled crystal oscillator expands VI’s advanced VCXO performance capabilities while adhering to a package foot- print compatible with the industry-common J-lead package. The VX-503 VCXO is a quartz stabilized square wave generator with either a CMOS output for driving CMOS/TTL loads or a PECL output. The device is packaged in a 6 pin J-lead ceramic package and is hermetically sealed with a grounded conductive lid.

Description

Parameter Min Typ Max Units Condition Pin Out Information for the CMOS output Option Pin Symbol Function Pin 1 VC VCXO Control Voltage Pin 2 Tri-State1 TTL logic low disables output. TTL logic high, or no connect, enables output. Pin 3 GND Case and Electrical Ground Pin 4 Output VCXO Output Pin 5 CMOS/TTL select1,2 TTL logic low optimizes symmetry for CMOS. TTL logic high, or NC, optimizes symmetry for TTL Pin 6 VCC Power Supply Voltage (5.0 V or 3.3 V ±10%) 1. Standard option. Tri-State can be connected to pin 5 and CMOS/TTL select would be on pin 2. 2. Output is HCMOS. For frequencies >12MHz, this option optimizes symmetry for either CMOS or TTL thresholds. Ground this pin for frequencies < 12MHz. Performance Speci/f_i cations

Performance Speci/f_i cations Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Parameter Min Typ Max Units Condition Electrical Performance @ 25°C for the CMOS output option Supply voltage 4.5 3.0 5.0 3.3 5.5 3.6 VDC VDC Current consumption 10mA + 0.25mA per MHz, typical Center Frequency 1.024 77.760 MHZ Absolute Pull Range over the operating temperature range, aging and power supply Vc= 0.5 to 4.5 or 0.3 to 3.0 V -100 -80 -50 -100 -80 -50 +100 +80 +50 +100 +80 +50 ppm ppm ppm ppm ppm ppm -40 ...+85 °C -40 ...+85 °C -40 ...+85 °C 0 ... +70 °C 0 ... +70 °C 0 ... +70 °C Gain Transfer Positive Output Level High 0.8 V Output Level Low 0.1 V Output Rise/Fall Time 5 ns Duty Cycle 45 Input Leakage ±1 uA Control Voltage Modulation BW 10 KHz RMS Jitter, 77.760MHz 3 ps RMS Jitter, 77.760MHz, 12kHz to 20MHZ <0.5 ps Maximum Control Voltage 0 Vdd Maximum Supply Voltage 7 V Storage Temperature -55 +125 °C Soldering Temp./Time 240/10 °C/s 1. Power supply bypass is required and a 0.1uF in parallel with a 0.01uF high frequency capacitor is recommended. 2. Figure 1 de/f_i nes these parameters. Figure 2 illustrates the load used to test devices. operation) Output Waveform Output Test Conditions (25±5°C) for 5 volt devices, 15pF cap only for 3.3V. Environmental Compliance Mechanical Shock MIL-STD-883, Method 2002 Mechanical Vibration MIL-STD-883, Method 2007 Solderability MIL-STD-883, Method 2003 Gross and Fine Leak MIL-STD-883, Method 1014 Resistance to Solvents MIL-STD-883, Method 2015

Performance Speci/f_i cations Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Parameter Min Typ Max Units Condition Re/f_l ow Pro/f_i le (IPC/JEDEC J-STD-020C) PreHeat Time Ramp Up Time Above 217 °C Time To Peak Temperature Time At 260 °C Ramp Down 60 sec Min, 180 sec Max 3 °C /sec Max 60 sec Min, 150 sec Max 480 sec Max 20 sec Min, 40 sec Max 6 °C /sec Max PECL Output Options Pin Symbol Function Pin 1 VC VCXO Control Voltage Pin 2 N/C or E/D2 No Connect or Output Disable Pin 3 GND Case and Electrical Ground Pin 4 Output VCXO Output Pin 5 COutput VCXO Complementary Output Pin 6 VCC Power Supply Voltage (5.0 V or 3.3 V ±10%) 1. By setting OD high, the outputs are disabled and OUT is held low while Complementary OUT is held high. Output is enabled if E/D < VCC-1.6V. 2. See ordering information for enable/disable option. Electrical Performance @ 25°C for the PECL output option Supply voltage 4.5 3.0 5.0 3.3 5.5 3.6 VDC VDC Current consumption frequency dependent Center Frequency 15 170 MHZ Absolute Pull Range over the operating temperature range, aging and power supply Vc= 0.5 to 4.5 or 0.3 to 3.0 V -50 -32 -50 -32 +50 +32 +50 +32 ppm ppm ppm ppm -40 ...+85 °C -40 ...+85 °C 0 ... +70 °C 0 ... +70 °C

Parameter Min Typ Max Units Condition Gain Transfer Positive Output Level High -1.025 -0.880 V Output Level Low -1.810 -1.620 V Output Logic Levels for -40 to 85 °C Operation Output Level High -1.085 -0.880 V Output Level Low -1.830 -1.555 V Output Rise/Fall Time 1 ns Duty Cycle 45 55 % Input Leakage ±1 mA Control Voltage Modulation BW 10 KHz RMS Jitter, 77.760MHz, 12kHz to 20MHZ <1 ps Maximum Control Voltage 0 Vdd V Maximum Supply Voltage 7 V Storage Temperature -55 +125 °C Soldering Temp./Time 240/10 °C/s 1. Power supply bypass is required and a 0.1uF in parallel with a 0.01uF high frequency capacitor is recommended. 2. Transition times are measured from 20% to 80% of a full 10K ECL level swing. Output Waveform Output Test Conditions (25±5°C) Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Performance Speci/f_i cations

Parameter Min Typ Max Units Condition Tape and Reel Dimensions (mm) Tape Dimensions Reel Dimensions Product A B C D E F G H I J K L # Per Reel J-Type 24 11.5 1.5 4 12 1.78 21 13 100 5 25 330 200 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Performance Speci/f_i cations

Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Outline Drawing / Enclosure

Ordering Information

VX - 503 0 - D A T - K X X 2 - 10M0000000 Product Family VX: VCXO Package 9 x 14 mm Height 0: B 4.5mm Supply Voltage D: 5 Vdc E: 3.3 Vdc Pullability Code H: ±32ppm K: ±50ppm P: ±80ppm S: ±100ppm Frequency Screening Code X: No Screening Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Rev: 3/2/2009 daf For Additional Information, Please Contact USA: Vectron International

267 Lowell Road

Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Europe: Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 3328.4784.17 Fax: +49 (0) 3328.4784.30 Asia: Vectron International 1F-2F, No 8 Workshop, No 308 Fenju Road WaiGaoQiao Free Trade Zone Pudong, Shanghai, China 200131 Tel: 86.21.5048.0777 Fax: 86.21.5048.1881 RF Output Code A: ACMOS B: TTL C: PECL Temperature Range E: -40… +85°C T: 0… +70°C Notes: Contact factory for improved stabilities or additional product options. Not all options and codes are available at all 1. frequencies. Unless other stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency 2. control voltage, load, temperature (25°C). Phase noise degrades with increasing output frequency. 3. Subject to technical modi/f_i cation. 4. Contact factory for availability. 5. Option Code 0: 6ps rms jitter 1: 12ps rms jitter 2: 20ps rms jitter Enable Code A: Enable Hi, Tristate X: No Enable