UG30APT GE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

ULTRAFAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage -50 to 200 Volts Forward Current -30.0 Amperes

FEATURES

♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Ideally suited for use in very high frequency switching power supplies, inverters and as a free wheeling diodes ♦ Ultrafast, 15 nanosecond typical recovery time ♦ Low leakage current ♦ Glass passivated chip junctions ♦ Soft recovery characteristics ♦ Excellent high temperature switching ♦ High temperature soldering guaranteed: 250°C, 0.16” (4.06mm) from case for 10 seconds MECHANICAL DATA Case: JEDEC TO-247AD molded plastic body over passivated chips Terminals:Plated leads solderable per MIL-STD-750, Method 2026 Polarity:As marked Mounting Position:Any Weight:2.2 ounces, 6.3 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS UG30APT UG30BPT UG30CPT UG30DPT UNITS Maximum repetitive peak reverse voltage V RRM 50 100 150 200 Volts Maximum RMS voltage V RMS 35 70 105 140 Volts Maximum DC blocking voltage V DC 50 100 150 200 Volts Maximum average forward rectified current at TC =120°C I (AV) 30.0 Amps Peak forward surge current 8.3 ms single half sine-wave superimposed I FSM 300.0 Amps on rated load (JEDEC Method) at TC =120°C Maximum instantaneous forward voltage per leg at 15A 1.0 30A VF 1.15 Volts 10A TJ=100°C 0.85 Maximum DC reverse current at T A =25°C 5.0 rated DC blocking voltage per leg T A =100°C IR 800.0 µA Maximum reverse recovery time (NOTE 1) trr 20.0 ns Maximum reverse recovery time T J= 25°C 35.0 (NOTE 2) TJ=100°C trr 50.0 ns Maximum recovered stored charge T J=25°C 22.0 (NOTE 2) TJ=100°C Q rr 50.0 nC Typical junction capacitance (NOTE 3) C J 70.0 pF Typical thermal resistance (NOTE 4) R Θ JC 2.0 °C/W Operating and storage temperature range T J, TSTG -65 to +150 °C NOTES : (1) Reverse recovery test conditions: IF=0.5A, IR =1.0A, Irr=0.25A (2) trrand Qrrmeasured at: IF=15A VR =30V, di/dt=50 A/µs, IRR =10% IRM for measurement of trr (3) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (4) Thermal resistance from junction to case per leg mounted on heatsink PIN 1 PIN 3 CASE 0.245 (6.2) 0.225 (5.7) 0.645 (16.4) 0.625 (15.9) 0.323 (8.2) 0.313 (7.9) 0.142 (3.6) 0.138 (3.5) 0.170 (4.3) 0.086 (2.18) 0.076 (1.93) 0.160 (4.1) 0.140 (3.5) 0.225 (5.7) 0.205 (5.2) 0.127 (3.22) 0.117 (2.97) 0.048 (1.22) 0.044 (1.12) 0.795 (20.2) 0.775 (19.6) 0.840 (21.3) 0.820 (20.8) 1 2 3

0.078 REF

(1.98) 0.203 (5.16) 0.193 (4.90) 10o TYP. BOTH SIDES 30o10o 1o REF. 0.118 (3.0) 0.108 (2.7) 0.030 (0.76) 0.020 (0.51) BOTH SIDES PIN 2 TO-247AD Dimensions in inches and (millimeters)

RATINGS AND CHARACTERISTIC CURVES UG30APT THRU UG30DPT 0.1 1 10 100 100 0 25 50 75 100 125 150 1750 1 10 100 100 1,000 0.01 0.1 100 0 25 50 75 100 125 150 1750 02 04 06 08 0 1 0 00.01 0.1 100 1,000 FIG. 1 - FORWARD CURRENT DERATING CURVE CASE TEMPERATURE, °C AVERAGE FORWARD CURRENT, AMPERES FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG di/dt=150 A/µs di/dt=100 A/µs di/dt=20 A/µs di/dt=50 A/µs di/dt=100 A/µs di/dt=150 A/µs di/dt=50 A/µs di/dt=20 A/µs FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG INSTANTANEOUS FORWARD VOLTAGE, VOLTS INSTANTANEOUS FORWARD CURRENT, AMPERES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG PEAK FORWARD SURGE CURRENT, AMPERES REVERSE VOLTAGE, VOLTSJUNCTION TEMPERATURE, °C TJ=125°C f=1.0 MHz Vsig=50mVp-p IF=15A VR =30V trr Q rr NUMBER OF CYCLES AT 60 H Z INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 6 - TYPICAL JUNCTION CAPACITANCE PER LEGFIG. 5 - REVERSE SWITCHING CHARACTERISTICS PER LEG JUNCTION CAPACITANCE, pF RECOVERED STORED CHARGE/REVERSE RECOVERY TIME, nC/ns TJ=25°C TJ=100°C TC =120°C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) TJ=25°C PULSE WIDTH=300 µs 1% DUTY CYCLE RESISTIVE OR INDUCTIVE LOAD