TVM4G-016.8M

TVM4G-016.8M CONNOR-WINFIELD | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 2

Technical content

Specifications subject to change without notice. All dimensions in inches. © Copyright 2008 The Connor-Winfield Corporation Bulletin Page Revision Date Tx227 1o f2

27 May 2008

5.0x7.0mm Clipped Sinewave Output The Connor Winfield model is a x .0mm Surface Mount emperature Compensated Crystal Oscillator ( TCXO). TVM4G 5.0 7 Voltage Controlled T VC Through the use of Analog Temperature Compensation, t is capable of holding sub 1-ppm stabilities he TVM4G over the -20 to 70 temperature range. Model TVM4G VCTCXO 3.0Vdc Operation Clipped Sinewave Output Logic Frequency Stability: Temperature Range: Low Jitter <1pS RMS 5.0 x 7.0mm Surface Mount Package Tape and Reel Packaging ±2.0ppm -20 to 70°C

2111 Comprehensive Drive

Aurora, Illinois 60505 Phone: 630-851-4722 Fax: 630-851-5040 www.conwin.com US Headquarters 630-851-4722: European Headquarters: +353-61-472221 Description Features Specification TVM4G 0828 16.8MHZ Absolute Maximum Ratings PARAMETER UNITS MINIMUM NOMINAL MAXIMUM UNITS NOTE Storage Temperature -55 - 125 °C Supply Voltage (Vcc) -0.5 - 6.0 Vdc Input Voltage (Vc) -0.5 - Vcc+0.5 Vdc Operating Specifications PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE Frequency Range - 16.8 - MHz Frequency Stability -2.00 - 2.00 ppm 1 Temperature Range -20 - 70 °C Power Supply Stability +/-5% -0.2 - 0.2 ppm Load Stability +/-5% -0.2 - 0.2 ppm Aging -1.0 - 1.0 ppm / year Supply Voltage (Vcc) 2.85 3.0 3.15 Vdc Supply Current (Icc) - - 2 mA Period Jitter - 3 5 ps rms Phase Jitter (BW=12kHz to 20MHz) - 0.5 1 ps rms SSB Phase Noise at 10Hz offset - -85 - dBc/Hz SSB Phase Noise at 100Hz offset - -115 - dBc/Hz SSB Phase Noise at 1KHz offset - -135 - dBc/Hz SSB Phase Noise at >10KHz offset - -150 - dBc/Hz Input Characteristics PARAMETER MINIMUM NOMINAL MAXIMUM UNITS Notes Control Voltage 0.5 1.5 2.5 V Frequency Tuning Range +/-10 - - ppm Linearity +/-5 - - % Slope Positive Input Impedance 100K - - Ohms Clipped Sinewave Output Characteristics PARAMETER MINIMUM NOMINAL MAXIMUM UNITS Notes Output Voltage 0.8 - - V 2 Output Load Resistance - 10.0K - Ohm Output Load Capacitance - 10.0 - pF

Aurora, Illinois 60505 Phone: 630-851-4722 Fax: 630-851-5040 www.conwin.com Specifications subject to change without notice. All dimensions in inches. © Copyright 2008 The Connor-Winfield Corporation US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Bulletin Page Revision Date Tx227 2o f2 120°C 150°C 180°C 260°C 220°C 360 Sec. Max. 120 S Max. 10 S 60 S Max. Time Temperature 260°C Pin ConnectionsPackage Layout Suggested Pad Layout Solder Profile Test Circuit

Ordering Information

TVM4G - 016.8M TCXO SERIES CENTER FREQUENCY Tape and Reel Information Typical Phase Noise Output Waveform 200 mV/Div Environmental Characteristics Vibration: Vibration per Mil Std 883E Method 2007.3 Test Condition A Shock: Mechanical Shock per Mil Std 883E Method 2002.4, Condition B. Soldering: See solder profile page 2. Sollderability Sollderability per Mil Std 883E Method 2003 Note: 1) Frequency stability vs. change in temperature, referenced to the mid point between minimum and maximum frequency value over the specified temperature range. 2) AC coupled. Dimensional Tolerance: ±.005 (.127mm) ±.02 (.508mm) 0.276 0.006 (7.0mm) 0.197 0.006 (5.0mm) 0.079 Max. (2.0mm) 0.03 (0. mm) (4 Places) 0.0 ( mm) 1.40 (4 Places) Pad 1 1 2 (Bottom View) (Top View) TVM4G 0828 16.8MHZ

1 Control Voltage

2 Ground

3 Output

4 Supply Voltage (Vcc)

(Top View) 1 2 Model TVM4G-016.8MHz 10 pF10Kohm 1 2 VC DNC DNC DNC DNC DNC OutputVcc Supply Voltage.01 uF Bypass DNC 0.69 (17.53mm) 0.08 (2.0mm) 0.08 (2.0mm) 3.15 (80mm) 9.84 (250mm) 0.08 (2.0mm) 8.45 Dia. (214.6mm) 1.0 Dia. (25.4mm) 4-PAD Ceramic Package Standard Orientation Meets EIA-481A and EIJ-1009B 2000 Pieces/Reel Maximum. Direction of Feed (Customer) 0.157 (4mm) 0.079 (2mm) 0.020 R. (0.5mm) 0.63 (1.6mm) Dia. 0.059 (1.5mm) Dia. 0.069 (1.75mm) 0.295 0.626 (15.90mm) 0.059 (1.5mm) Dia. Minimum Pocket Size (Ao) (Bo) (Ko) 5.33mm (0.21”) 7.87mm (0.31”) 3.07mm (0.121”) 16mm (0.630”) Width 8mm (0.315”) Pitch Typical 0.210 (5.33mm) (Ao) 0.121 (3.07mm) (Ko) 0.315 (8.0mm) Typical 0.31 (7.87mm) (Bo) 0.014 (+/-.004) (0.36mm +/-.01) SM-MECH09