HSM59 CONNOR-WINFIELD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
CONNOR—WINFIELD sree oes PHONE (630) 851-4722 CORPORATION FAX (630) 851-5040 SPECIFICATIONS HSM59 Frequency Range 1.8MHz to 80MHz +30ppm input voltage change, load change, aging, shock and vibration) Temperature Range Oc to +70°C Waveform HCMOS Squarewave Load SOpF Voltage Voh 4.5V_ Minimum Vol 0.5V_ Maximum Output Coerent lon tl Duty Cycle 45/55% Maximum Rise/Fall Time Output E/D Time 100nS Maximum Enable Vih 2.2V_ Minimum Input lih 400uUA Maximum , 30uA Typical npu Disable Vil 0.8V_ Maximum fil 400uA Maximum , SOuUA Typical Start Up Time 10mS Maximum Supply Voltage +5Vde 410% 1.8MHz to 20MHz: 20mA Maximum 20MHz to SOMHz: 30mA Maximum Supply Current 5OMHz to 70MHz: 50mA Maximum 7OMHz to 80MHz: _80mA Maximum .060 MAX (1.50mm) [PIN] CONNECTION]
197 MAX -— 102
(5.00mm) (2.60mm) oe [3] oureur | | Bs | Dimensional Tolerance: .005 2 $ 3 (13mm) .295 MAX -200 (7.50mm) -028 Sonn) (8.08mm) ORDERING INFORMATION (.71mm) : ! CLOCK J L CENTER (sen) <L 004 REF L087 SERIES FREQUENCY ° (10mm) Specifications subject to change without notice _ ars er
CONNOR-—WINFIELD sno eee PHONE (630) 851-4722 CORPORATION vex (630 861-00 OUTPUT WAVEFORM TEST CIRCUIT TTT ® OSCILLOSCOPE Tr) - —) Tr - te 8 PROBE +4.5Vde 90% Vcc | |POWER : @ [aot +2.5Vde 50% Vee +0.5Vd ae - Svde — 10% vee a Ty 0.0Vde "O” LEVEL + iT i Til FRED SYMMETRY INPUT FOR E/D O COUNTER MECHANICAL CHARACTERISTICS ENVIRONMENTAL CHARACTERISTICS TEMPERATURE CYCLE: FREE DROP: The specimen shall meet electrical characteristics after The specimen shall meet electrical characteristics after tested 5 cycles of 55 C/30 min & +125 C/30 min. tested 3 times Free Drop testing on the hard wooden board froma height of 75cm. 2 HERMETICAL in Flourinert (FC=43) ot VIBRATION: mest electrical enoracterstice of 125-0 +/-5'6, for 5 minutes ° 1 specimen shall meet electrical characteristics after tested by the following conditions; SOLVENT RESISTANCE: 10-55Hz 1.5mm Amplitude, 55-2000Hz 206’s, Marking will withstand immersion in Isopropyl Alcohol 2 hours for each plane. or Trichloroethylene. THERMAL SHOCK: After applied Thermal Shock of 260 C max x 10 sec max SOLDERING x 2 times, or 230 C max x 180 sec max, the specimen shall meet electrical characteristics. GENERAL CONDITIONS: SOLDERABILITY: (ElAJ-RCX—0102/101 Condition 1a) 260°C max x 10 sec max x 2 times max or 1, Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl alcohol=75%) 230°C mox x 180 sec max x 1 time. 2. Solder: QQ-S-571 (Sn=63%, Pb=37%) 3. Solder bath temperoture: 235 C +/-5 C. TYPICAL OPERATION DATA (Vopor phase reflow) 4. Depth of immersion: Up to electrical terminal. 20 to 100 sec up to 215°C, 50 sec at 215°C then 5. immersing time: Within 2 sec +/—0.5 sec into solder down to room temperature per 1 to 5°C/sec bath. After performing the above procedures, a newly soldered coverage shall be greater than 90%. | ( PIN 1 TAPING AND REEL 69 / DIMENSIONS (75mm) Snes i ered .08 08 (7.9mm)] a bes ny (2.0mm) (2.0mm) | ‘4 SUGGESTED PAD LAYOUT | ooh AY ow 9.84 { 3 | (250mm DIA) [e] 3 ae, Zi 8} 40mm TT 165 08 —— @ Ker) 3.15 318 [e] a (4-2men) 4 f_]c-by Dh (60mm) (6.0mm) ol\\..06 oA 7] |_| fl j j Te] ol erm on _ [ROUND]
1.00 DIA Lo] Ql 078 TYP | |~ o70 1A
(25mm DIA) 3 (2.0mm) (1.8mm) ani Bypass capacitor, C—by, should be —|__|— 295 (7.5mm) | ceramic capacitor > .Otuf. MEETS EIA—481A AND EIAJ—1009B oa .07(1.75mm) | Specifications subject to change 2,000 _PCS/REEL 63 (160mm) | without notice. suueTin ¢, —SMO17 | rey, 05 pace 2 of 2 | pave: _8/6/01_ ISSUED_BY: —___