TS2-I-24V-800S

TS2-I-24V-800S PANASONIC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 1

Technical content

• The elegant solution to time delay problems.
• High repeat accuracy and reliability.
• Not susceptible to external disturbance.
• Increase in timing delay by using an external capacitor with time-off delay device – o –.
• No auxiliary power supply required with time-off delay operation.
• No „first cycle effect“, with the time-on delay device. The first and following operations are of the same duration. en_ds_61708_0000_300506D TS + The trimmer is omitted on the -i/-o- 0s device. This must be replaced by an external potentiometer. The time delay thus achievable is 20s per 100 kΩ Ωwith the -i- devices and approx 20s per 1 MΩ Ωwith the -o- devices. The minimum time delays are 1s (with -i-) and 0.3 s (with -o-). * With the -o- 0s device, the pulse frequency is 5 Hz. max., and is inversely proportional to Rext(e.g. at 12 kΩ Ωthe pulse frequency is 1 Hz). ** Connect C ext between pins 12 and 13! Note: Excitation voltage ripple should be maintained below 5% by use of appropriate smoothing. Strong external magnetic fields influence relay data. 1)Data concerning operational life is based on resistive loads and ambient temperature of 20-30°C. TR-W Wiping function on requestWith surge voltages (1.2/50µsec) over DC 500V TS-i. b. w relays may not operate as intended. Characteristics Remarks Operation Contact arrangement Max. make/rated/break current A Voltage switching range V Power switching range W (VA) Contact material Volumetric/contact resistance m Ω Ω Operational life 5 A, 1000 VA / 5 A, 100 W switching ops. 4 A, 1000 VA / 0.1 A, 1 W switching ops. Voltage withstand: cont./cont.- control circuitry Veff Insulation resistance: cont./cont.- control circuitry Ω Ω Shock-, vibration resistance g, g/Hz Life of trimmer Type of protection Potentiometer/Contacts Storage temperature °C Permiss. ambient temp. at max. load °C Min. control pulse duration at rated voltage. ms 20 / 5 / 5 10-5-250 10-10-100 (1000) AuAg10 6 ·104 / 3 · 105 105 / 2 · 108 1013/1 010 50, 20 / 1000 >100 operations -20 / +85 -20 / +65 100 dust tight / IP50 See also the S relay data sheet Independant of position Typically 1000 ops. Consequently, time tol.: < 4% with -i- devices 25 % with -0- devices Operating characteristics Type: – i – ”on“ delay – b – pulse relay TS2-/TS3-/TS4 – i / – b – 5 V TS2-/TS3-/TS4 – i / – b – 12 V TS2-/TS3-/TS4 – i / – b – 24 V Rated time: „on“ delay „i“ 0 s +) 10s 100s 800s Minimum timing range [s] typical at rated voltage 1-1000 0.3-10 1-100 8-800 Time tolerance at U rated± 10% < 1% pulse relay „b“ pulse frequency 0.04 … 5 Hz* Operating voltage V 4.0 – 9.0 8.5 – 18.0 17.0 – 30.0 Current consumpt. mA Type: – o – ”off“ delay TS2-/TS3-/TS4 – o – 5 V TS2-/TS3-/TS4 – o – 12 V TS2-/TS3-/TS4 – o – 24 V Rated time: „off“ delay „o“ 0 s +) 10 s 100 s Minimum timing range [s] typical at rated voltage 0.3-100 0.3-10 1-100 Time tolerance at U rated± 10% – approx 20% Time delay increase with Cextper µF** – 1.5s 4.7 s Operating voltage V 4.0 – 9.0 8.5 – 18.0 18.0 – 28.0 Current consumpt. mA Connection diagrams (bottom view) Warning! No reverse battery protection Ordering example TS2–i, –o– or –b – 5, 12, 24 V – 0 s TS3–i, –o– or –b – 5, 12, 24 V – 0 s TS4–i, –o– or –b – 5, 12, 24 V – 0 s TS2–i, –o– or –b – 5, 12, 24 V – 10 s or – 100 s – i – 800 s, – b – 25 s TS3–i, –o– or –b – 5, 12, 24 V – 10 s or – 100 s – i–800s, –b–25 s TS4–i, –o– or –b – 5, 12, 24 V – 10 s or – 100 s – i – 800 s, – b – 25 s (NO = normally open, NC = normally closed, CO = changeover) 2NO2NC (2CO)/3NO1NC (2NO1CO)/4NO W arning! pins 1 and 6 may not be connected. Pins 7 and 12 are negative and connected internally Approx. 15 g Housing material: CRASTIN SK-615 FR Polycarbonate Basic grid 2.54 mm PCB hole dia. /L501351.3 mm ± 0.1 mm