TRB255 TELTONIKA | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 14
Technical content
Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
+ - 9-30 VDC positive power pin CTS - RS232 clear data to send pin (output). RTS - RS232 request data to send pin (input). R+ - RS485 receiver positive signal pin. D+ - RS485 driver positive signal pin. - - Negative/ground power pin. - Ground pins for D1, D2, D3, A, RS232 and RS485. A - Analog input pin. Analog voltage range 0-30 V. TX - RS232 transmitted data (input). RX - RS232 received data (output). R- - RS485 receiver negative signal. D- - RS485 driver negative signal. DATASHEET // TRB255 HARDWARE FRONT VIEW BACK VIEW INPUT/OUTPUT 16 PIN CONNECTOR PINOUT D1, D2, D3 - Configurable digital Input/Output pins. Open collector output, max output 30 V, 300 mA or Digital input where 0-6 V detected as logic low and 8-30 V – logic high. Mobile signal strength indication LEDs Mobile antenna connector GNSS antenna connector Mobile network type LEDs Power LED Reset button Input/output connector Ethernet port Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
FEATURES
LTE (Cat M1) / NB-IoT / EGPRS 2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, on roaming, no network, network denied, data connection fail Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP Bytes sent/received, connected band, IMSI, ICCID. SIM switch Status MOBILE Mobile module Supports sending and reading Unstructured Supplementary Service Data messages SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, Call utilities USSD SMS/Call Tag based VLAN separation Custom data limits for both SIM cards VLAN (planned) Mobile quota control Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites onlyWEB filter (planned) Flexible access control of TCP, UDP, ICMP packets, MAC address filterAccess control Operator black/white list Used band status display, Band lock Black/White list Band management Auto APN Direct connection (bridge) between mobile ISP and device on LAN APN Bridge Possibility to use different PDNs for multiple network access and servicesMultiple PDN Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2) (planned) TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, PPP, SSH, DHCP, Telnet, MQTT, Wake On Lan (WOL) H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets Network protocols VoIP passthrough support (planned) NETWORK Routing Pre-shared key, digital certificates, X.509 certificates DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks) DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC Attack prevention SECURITY Authentication Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-TFirewall IKEv1, IKEv2, with 5 encryption methods (DES, 3DES, AES128, AES192, AES256) GRE tunnel IPSec GRE Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s codeStunnel (planned) Client/Server services can run simultaneously, L2TPv3 supportPPTP, L2TP Method of building scalable IPsec VPNsDMVPN (planned) SSTP client instance supportSSTP (planned) ZeroTier VPN client supportZeroTier WireGuard VPN client and server support Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice. WireGuard Multiple clients and server can be running simultaneously, 12 encryption methods VPN OpenVPN OpenVPN Encryption Ping Reboot, Periodic Reboot, LCP and ICMP for link inspection Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e Connection monitoring QoS / Smart Queue Management (SQM) (planned) Port forward, traffic rules, custom rulesFirewall Static and dynamic IP allocation, DHCP RelayDHCP Supported >25 service providers, others can be configured manually Possibility to mount remote file system via SSH protocol DDNS SSHFS 1 x LAN port 10/100 Mbps, comply IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover (Configurable to work as WAN port) ETHERNET LAN
Respond to one ID in range [1;255] or anyID filtering Allow access through WAN MODBUS TCP custom register block, which allows to read/write to a file inside the router, and can be used to extend MODBUS TCP slave functionality Allow remote access Custom registers SERIAL COMMMUNICATION MODES Console, OverIP, Modem (Full or Partial control), MODBUS RTU master, MODBUS gateway, NTRIP client (planned)Modes MODBUS RTU MASTER From 300 to 3000000Supported baud rates 01, 02, 03, 04, 05, 06, 15, 16 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII Supported functions Supported data formats 7 or 8Number of data bits 1 or 2 None, Even, Odd Number of stop bits Parity bits None, RTS/CTS (only for RS232 interface), Xon/XoffFlow control MODBUS TCP MASTER 01, 02, 03, 04, 05, 06, 15, 16Supported functions MQTT GATEWAY Allows sending commands and receiving data from MODBUS Master trough MQTT brokerGateway DATA TO SERVER HTTP(S), MQTT, Azure MQTT, KinesisProtocols 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCIISupported data formats SYSTEM CHARACTERISTICS Qualcomm QCA9531, MIPS 24kc, 650 MHzCPU
64 MB, DDR2
16MB SPI Flash (4 MB available for user) Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice. RAM Flash storage MONITORING & MANAGEMENT HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log Firmware update from server, automatic notification WEB UI FOTA SSH (v1, v2) SMS status, SMS configuration, send/read SMS via HTTP POST/GET SSH SMS OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystemTR-069 MQTT Broker, MQTT publisher SNMP (v1, v2, v3), SNMP Trap MQTT SNMP Management API over HTTP/HTTPSJSON-RPC MODBUS TCP status/controlMODBUS Teltonika Remote Management Systems (RMS)RMS IoT PLATFORMS Allows monitoring of: Device data, Mobile data, Network info, AvailabilityCloud of Things Allows monitoring of: WAN Type, WAN IP Mobile Operator Name, Mobile Signal Strength, Mobile Network Type Allows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength, WAN Type and IP ThingWorx Cumulocity Can send device IP, Number of bytes send/received/ 3G connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, Sim State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type, Temperature, PIN count to Azure IoT Hub server Azure IoT Hub
2 pins in 16 pin industrial terminal blockConnector 9 – 30 VDC, reverse polarity protection, surge protection +/-1 kV 50 µs max Idle: <1.2 W, Max: <5 W Input voltage range Power consumption PHYSICAL INTERFACES (PORTS, LEDS, ANTENNAS, BUTTON, SIM) 1 x RJ45 port, 10/100 MbpsEthernet 3 x Configurable I/O, 1 x Analog input in 16 pin terminal block 3 x connection status LEDs, 3 x connection strength LEDs, 1 x power LED, 1 x Eth port status LED I/O’s Status LEDs 2 x SIM slots (Mini SIM – 2FF), 1.8 V/3 V, double stacked SIM tray 2 pins in 16 pin terminal block SIM Power 1 x SMA connector for LTE, 1 x SMA connector for GNSS 4 pins in 16 pin terminal block (TX, RX, RTS, CTS) Antennas RS232 4 pins in 16 pin terminal block (D+, D-, R+, R-) Reboot/User default reset/Factory reset button RS485 Reset FIRMWARE / CONFIGURATION Update FW from file, check FW on server, configuration profiles, configuration backupWEB UI Update FW/configuration from server Update FW/configuration for multiple devices FOTA RMS Update FW without losing current configurationKeep settings LOCATION TRACKING GPS, GLONASS, BeiDou, Galileo and QZSSGNSS GNSS coordinates via WebUI, SMS, TAVL, RMS NMEA 0183 Coordinates NMEA NTRIP protocol (Networked Transport of RTCM via Internet Protocol)NTRIP (planned) Supported server software TAVL, RMS Configurable multiple geofence zones Server software Geofencing INPUT/OUTPUT 3 x Configurable Inputs/Outputs. Digital input 0 - 6 V detected as logic low, 8 - 30 V detected as logic high. Open collector output, max output 30 V, 300 mAConfigurable I/O 1 x Analog input (0 - 30 V) HTTP POST/GET, Schedule Analog input Output control SMS, EmailEvents Allows to set certain I/O conditions to initiate eventI/O juggler SERIAL Terminal block connector: TX, RX, RTS, CTSRS232 Terminal block connector: D+, D-, R+, R- (2 or 4 wire interface) From 300 to 3000000 RS485 Supported baud rates 7 or 8Number of data bits 1 or 2 None, Even, Odd Number of stop bits Parity None, RTS/CTS (only for RS232 interface), Xon/XoffFlow control FIRMWARE CUSTOMIZATION RutOS (OpenWrt based Linux OS)Operating system Busybox shell, Lua, C, C++Supported languages SDK package with build environment providedDevelopment tools Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
Aluminium housing with DIN rail mounting optionCasing material 83 x 25 x 74.2 mm 165 g Dimensions (W x H x D) Weight OPERATING ENVIRONMENT -40 C to 75 COperating temperature 10% to 90% non-condensingOperating humidity DIN rail, wall mounting (additional kits needed), flat surface placementMounting options Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
A. B. admin admin01 Bytes received/sent* SIM card slot in use Data connection state State LOGIN TO DEVICE 1. Unscrew two back panel hex bolts and remove the back panel. 2. Insert your SIM card(s) into the SIM socket(s), which are located on the bottom side of PCB. 3. Attach the panel and tighten the hex bolts. 4. Attach the mobile antenna (max torque 0.4 N·m / 3.5 lbf·in). 5. Connect open PSU leads to 16 pin terminal block: a) red wire to top row first contact (+); b) black wire to bottom row first contact (-). 6. Connect the 16 pin terminal block to gateway 16 pin connector and plug other end of the power adapter into a power outlet. 1. Power on the device and connect the Ethernet cable to your computer. 2. Allow the gateway to boot up. This might take up t 4. Use login information shown in image A when prompted for authentication. 5. After you log in, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter and one digit. This step is mandatory, and you will not be able to interact with the gateway WebUI until you change the password. 6. When you change the gateway password, the Configuration Wizard will start. The Configuration Wizard is a tool used to set up some of the gateway main operating parameters. 7. Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions. HARDWARE INSTALLATION *Order code dependent. **Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations. Bundled accessories specifications* Radio specifications RF technologies Max RF power EGPRS, NB-IoT, LTE (Cat-M1), GNSS 33 dBm@GSM, 23 dBm@LTE Mobile antenna 698~960 / 1710~2690 MHz, 50 Ω, VSWR < 3, gain 3 dBi, omnidirectional, SMA male connector GNSS antenna 1575.42~1602 MHz, 2.2~5 VDC, VSWR < 1.5, gain 28 dB (typ.), RHCP polarization, SMA male connector Power adapter Input: 0.4 A@100-240 VAC, output: 9 VDC, 1 A, connected to 16 pin terminal block TECHNICAL INFORMATION -65 dBm Connected Registered (home); OPERATOR; 4G (LTE) Ready 348.7 KB / 223.5 KB Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
STANDARD PACKAGE CONTAINS*
- TRB255
- 9 W PSU
- 1 x Mobile antenna (swivel, SMA male)
- 1x GNSS antenna (adhesive, SMA male, 3 m cable)
- 16 pin terminal block
- 1 x hex key
- Ethernet cable (1.5 m)
- QSG (Quick Start Guide)
- RMS Flyer
- Packaging box DATASHEET // TRB255 WHAT'S IN THE BOX? TRB255 9 W PSU 1X GNSS ANTENNA (ADHESIVE, SMA MALE, 3 M CABLE) ETHERNET CABLE (1.5 M)
16 PIN TERMINAL BLOCK 1 X HEX KEY
1 X LTE ANTENNA (SWIVEL, SMA
MALE) * For all standard order codes standard package contents are the same, execpt for PSU. Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
PRODUCT CODE PACKAGE CONTAINSHS CODE HTS CODE STANDARD ORDER CODES TRB255 000000 For more information on all available packaging options – please contact us directly. 851762 8517.62.00 Standard Package with Euro PSU TRB255 000100 851762 8517.62.00 Standard Package with US PSU PRODUCT CODE FREQUENCYREGION (OPERATOR) AVAILABLE VERSIONS The price and lead-times for region (operator) specific versions may vary. For more information please contact us. Global 4G (LTE-FDD): B1, B2, B3, B4, B5, B8, B12, B13, B18, B19, B20, B28 4G (LTE-TDD): B39 (for Cat M1 only) 2G: B2, B3, B5, B8 Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
Philips Pan Head screw #6-32×3/16, 2pcs 82 mm x 46 mm x 20 mm V DIN RAIL KIT DIN Rail adapter Philips Pan Head screw #6-32×3/16, 2pcs for RUT2xx/RUT9xx ORDER CODE HTS CODEHS CODE PR5MEC00 For more information on all available packaging options – please contact us directly. 73269098 7326.90.98 SURFACE MOUNTING KIT Parameter Mounting standard Material Weight Screws included Dimensions RoHS Compliant Value Flat surface mount ABS + PC plastic 2x5 g Philips Pan Head screw #6-32×3/16, 2pcs 25 mm x 48 mm x 7.5 mm V DIN RAIL KIT Surface mounting kit Philips Pan Head screw #6-32×3/16, 2pcs ORDER CODE HTS CODEHS CODE PR5MEC12 For more information on all available packaging options – please contact us directly. 73269098 7326.90.98 COMPACT DIN RAIL KIT Parameter Mounting standard Material Weight Screws included Dimensions RoHS Compliant Value 35mm DIN Rail ABS + PC plastic 6.5 g Philips Pan Head screw #6-32×3/16, 2pcs 70 mm x 25 mm x 14,5 mm V DIN RAIL KIT Compact plastic DIN Rail adapter (70x25x14,5mm) Philips Pan Head screw #6-32×3/16, 2pcs ORDER CODE HTS CODEHS CODE PR5MEC11 For more information on all available packaging options – please contact us directly. 73269098 7326.90.98 Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
TRB255 SPATIAL MEASUREMENTS & WEIGHT DATASHEET // TRB255 MAIN MEASUREMENTS W x H x D dimensions for TRB255: Device housing*: Box: 83 x 25 x 74.2 173 x 71 x 148 TOP VIEW The figure below depicts the measurements of TRB255 and its components as seen from the top: RIGHT VIEW The figure below depicts the measurements of TRB255 and its components as seen from the right side: *Housing measurements are presented without antenna connectors and screws; for measurements of other device elements look to the sections below. Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
The figure below depicts the measurements of TRB255 and its components as seen from the front panel side: FRONT VIEW The figure below depicts the measurements of TRB255 and its components as seen from the back panel side: REAR VIEW Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
The figure below depicts an approximation of the device's dimensions when cables and antennas are attached: MOUNTING SPACE REQUIREMENTS Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.
The scheme below depicts protrusion measurements of an attached DIN Rail: DIN RAIL Copyright © 2022, TELTONIKA NETWORKS. Specifications and information given in this document are subject to change by TELTONIKA NETWORKS without prior notice.