TPT7710F-SOAR

TPT7710 3PEAK | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 28

Technical content

Features

• 150-Mbps Data Rate
• 5-kV RMS Isolation Rating (WSOP)
• ±200-kV/μs typ Static CMTI, ±150-kV/μs typ Dynamic CMTI
• Low Power Consumption, typ 3 mA/ch @1 Mbps
• Low Propagation Delay: 12 ns Typical
• Default Output Low (TPT7710F) and High (TPT7710)
• Wide Temperature Range: −40°C to +125°C
• SOP8, WSOP8, and WSOP16 Packages
• Robust Electromagnetic Compatibility (EMC) – Low Emissions – System-Level ESD, EFT, and Surge Immunity
• Safety-Related Certifications: – VDE Certification according to DIN VDE V 0884-17(IEC60747-17) – 5000-VRMS (WSOP16, WSOP8), 3750-VRMS (SOP8) Isolation Rating per UL 1577 – CQC Certification per GB 4943.1 – CSA, TUV, and CB Certifications

Applications

• Industrial Automation
• Motor Control
• Power Supplies
• Isolated Interface and General-Purpose Isolation

Description

The TPT7710 devices are high-performance, dual-channel enhanced digital isolators with 5000-V RMS (WSOP8, WSOP16), and 3750-VRMS (SOP8) isolation ratings per UL 1577. These devices have also been certified by VDE, UL, CSA, TUV, CQC, and CB. The TPT7710 devices provide high reliability and high performance at low power consumption with isolating digital input and output. Each isolation signal channel is separated by a double capacitive silicon dioxide insulation barrier. In the event of input power or signal loss, the fail- safe default output is low for devices with the suffix F and high for devices without the suffix F. The common mode transient immunity (CMTI) and electromagnetic compatibility of the TPT7710 devices have been significantly enhanced through innovative circuit design and optimized structure. The TPT7710 family is available in SOP8, WSOP8, and WSOP16 packages, and is characterized from −40°C to +125°C. Functional Block Diagram VCCA GNDA GNDB Isolation Capacitor Isolation Capacitor OUTx INx Isolation Barrier OOK Modulator High CMTI Demodulator RF Clock EME Reduction VCCB TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 1 / 28 CA20230702A0

1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 2 / 28 CA20230702A0

Revision History

2020-05-05 Rev.Pre.0 Initial Version 2022-10-05 Rev.A.0 Released version TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 3 / 28 CA20230702A0

Table 1. Pin Functions: TPT7710

Absolute Maximum Ratings (1) Parameter Min Max Unit VCC Supply Voltage, VCCA, VCCB −0.5 6 V VIO Voltage at IN, OUT −0.5 VCC + 0.5 V IO Output Current −15 15 mA TJ Operating Virtual Junction Temperature - 150 °C Tstg Storage Temperature −65 150 °C (1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. ESD, Electrostatic Discharge Protection Parameter Condition Value Unit HBM, per ANSI/ESDA/JEDEC JS-001/ANSI/ESD STM5.5.1 (1) All Pin ±8 kV CDM, per ANSI/ESDA/JEDEC JS-002 (2) All Pin ±2 kV Latch up, per JESD78 All Pin ±600 mA (1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. (2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Recommended Operating Conditions Parameter Min Typ Max Unit VCCX Supply Voltage, VCCA, VCCB (1) 2.25 - 5.5 V VCC(UVLO+) UVLO threshold when supply voltage is rising (2) - 2 2.25 V VCC(UVLO+) UVLO threshold when supply voltage is falling (2) 1.7 1.85 - V VHYS(UVLO) Supply Voltage UVLO Hysteresis 60 150 - mV IOH High-Level Output Current VCCB = 5 V −4 - - mA VCCB = 3.3 V −2 - - mA VCCB = 2.5 V −1 - - mA IOL High-Level Output Current VCCB = 5 V - - 4 mA VCCB = 3.3 V - - 2 mA VCCB = 2.5 V - - 1 mA VIH High-Level Input Voltage (data input) 2 - VCC V VIL Low-Level Input Voltage (data input) 0 - 0.8 V fdata Data Rate (3) 0 - 150 Mbps TA Operating Ambient Temperature −40 25 125 °C (1) VCCA is input side VCC; VCCB is output side VCC; TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 5 / 28 CA20230702A0

(2) VCC(UVLO+), VCC(UVLO+), VHYS(UVLO) are same to VCCA and VCCB; (3) 150 Mbps is the maximum specified data rate, although higher data rates are possible. Thermal Information Package Type θJA θJC Unit SOP8 130 48 °C/W WSOP8 85 43 °C/W WSOP16 93 52 °C/W Insulation Specifications Parameter Conditions Value Unit SOP8 WSOP8 WSOP16 CLR External clearance Shortest terminal-to-terminal distance through air > 4.0 > 8.0 > 8.0 mm CPG External creepage Shortest terminal-to-terminal distance across the package surface > 4.0 > 8.0 > 8.0 mm DTI Distance through the insulation Minimum internal gap (internal clearance) > 22 > 22 > 22 μm DTC Distance through the Molding compound Minimum internal distance across the conductors inside the package 0.45 0.8 0.8 mm CTI Comparative tracking index > 600 > 600 > 600 V Material group I I I Over-voltage category For Rated Mains Voltage ≤ 150 VRMS I-IV I-IV I-IV For Rated Mains Voltage ≤ 300 VRMS I-III I-IV I-IV For Rated Mains Voltage ≤ 600 VRMS I-II I-IV I-IV For Rated Mains Voltage ≤ 1000 VRMS I I-III I-III Climatic category 40/125/21 40/125/21 40/125/21 Pollution degree 2 2 2 DIN V VDE V 0884-17 (1)(2) VIORM Maximum repetitive isolation voltage AC voltage 637 1414 1414 VPK VIOWM Maximum working isolation voltage AC voltage; TDDB Test 450 1000 1000 VRMS DC voltage 637 1414 1414 VDC VIOTM Maximum transient isolation voltage VTEST = VIOTM, t = 60 s (qualification); VTEST = 1.2 x VIOTM, t = 1 s (100% production) 5300 7070 7070 VPK VIOSM Maximum surge isolation voltage(3) Test method per IEC 62368-1, 1.2/50 μs waveform, VTEST = 1.3 × VIOSM (qualification) 5980 6500 6500 VPK TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 6 / 28 CA20230702A0

Method a, After Input/Output safety test subgroup 2/3, Vini = VIOTM, tini = 60 s; Vpd(m) = 1.2 × VIORM, tm = 10 s ≤ 5 ≤ 5 ≤ 5 pC Method a, After environmental tests subgroup 1, Vini = VIOTM, tini = 60 s; Vpd(m) = 1.6 × VIORM, tm = 10 s ≤ 5 ≤ 5 ≤ 5 Method b1; At routine test (100% production) and preconditioning (type test), Vini = 1.2 x VIOTM, tini = 1 s; Vpd(m) = 1.875 × VIORM, tm = 1 s ≤ 5 ≤ 5 ≤ 5 CIO Isolation capacitance VIO = 0.4 × sin (2πft), f = 1 MHz ~0.5 ~0.5 ~0.5 pF RIO Isolation resistance VIO = 500 V, T A= 25°C > 1012 > 1012 > 1012 Ω VIO = 500 V, 100°C ≤ T A≤ 125°C > 1011 > 1011 > 1011 Ω VIO = 500 V at T S= 150°C > 109 > 109 > 109 Ω UL 1577 VISO Withstanding isolation voltage VTEST= VISO , t = 60 s(qualification); VTEST= 1.2 × VISO, t = 1 s (100% production) 3750 5000 5000 VRMS (1) All pins on each side of the barrier are tied together creating a two-terminal device. (2) This coupler is suitable for safe electrical insulation only within the safety operating ratings. Compliance with the safety ratings shall be ensured by means of suitable protective circuits. (3) Testing must be carried out in oil. TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 7 / 28 CA20230702A0

Safety-Related Certifications VDE UL TUV CQC CSA CB Certified according to DIN VDE V 0884-17 Certified according to UL 1577 and CSA Component Acceptance Notice Certified according to EN IEC 62368-1 and EN IEC 61010-1 Certified according to GB 4943.1 Certified CSA C22.2 No. 62368-1 and CAN/CSA- C22.2 No. 60601-1 Certified according to EN IEC 62368-1 Basic insulation (WSOP) VIORM=

1414 VIOSM=

(SOP) VIORM= 637 VIOSM= 5980 (WSOP)Single protection, 5000Vrms (SOP)Single protection, 3750Vrms 6400Vrms reinforced insulation (WSOP), 800Vrms maximum work voltage. 4000Vrms basic insulation (SOP), 400V rms maximum work voltage. Reinforced insulation (WSOP), Altitude<=5000m,8 00V rms maximum work voltage. Basic insulation (SOP), Altitude<=5000m,4 00V rms maximum work voltage. 400Vrms basic insulation (SOP) and 600V rms reinforced insulation (WSOP) working voltage per CSA C22.2 No. 62368-1:19 3rd, IEC 62368-1:2018 Ed. 3(in pollution degree 2, material group I)

2 MOPP (Means of

Patient Protection) insulation requirements for 250Vrms (WSOP) in CAN/CSA-C22.2 No. 60601-1:14, IEC 60601-1:2005 + AMD1:2012 Reinforced insulation (WSOP), Altitude<=5000m,8 00V rms maximum work voltage. Basic insulation (SOP), Altitude<=5000m,4 00V rms maximum work voltage. Certificate No. 40054570 Report Reference E524241 Customer No. 2332359 Certificate No. CQC21001303701 CQC22001332218 CQC23001393273 Master contract: 302375 Ref. Certif. No. CN54369 CN56354 CN60001 TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 8 / 28 CA20230702A0

Parameter Conditions (1) Min Typ Max Unit Safety Supply Current RθJA = 130°C/W, VI = 5 V, TJ = mARθJA = 85°C/W, VI = 5 V, TJ = 150°C, TA = 25°C (WSOP8) - - 294.1 RθJA = 93°C/W, VI = 5 V, TJ = 150°C, TA = 25°C (WSOP16) - - 268.8 Safety Total Power RθJA = 130°C/W, TJ = 150°C, TA = mWRθJA = 85°C/W, TJ = 150°C, TA = RθJA = 93°C/W, TJ = 150°C, TA = 25°C (WSOP16) - - 1344 Maximum Safety Temperature - - - 150 °C (1) The assumed junction-to-air thermal resistance in the Thermal Information is that of a device installed on a high-K test board for leaded surface-mount packages. TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 9 / 28 CA20230702A0

Electrical Characteristics

All test condition is at V CCA = V CCB = 2.25 V to 5.5 V, T A = −40°C to +125°C, Typical value is in V CC = 3.3 V, T A = +25°C, unless otherwise noted. Parameter Conditions Min Typ Max Unit Input Electrical Specifications VIH Logic Input High Voltage Input signal, IN 2.0 - - V VIL Logic Input Low Voltage Input signal, IN - - 0.8 V VIT+ Rising Input Threshold Voltage Input signal, IN - 1.6 2 V VIT− Falling Input Threshold Voltage Input signal, IN 0.8 1.2 - V VHYS Input Threshold Voltage Hysteresis - 0.4 - V IIH High-Level Input Current VIH = VCCA at IN (1) - 2.5 10 μA IIL Low-Level Input Current VIL = 0 V at IN (1) −10 −2.5 - µA IOH High-Level Output Current mAVCCB = 3.3 V ± 10% −2 - - IOL Low-Level Output Current VCCB = 5 V ± 10% - - 4 mAVCCB = 3.3 V ± 10% - - 2 VCCB = 2.5 V ± 10% - - 1 VOH High-Level Output Voltage VCCB= 5 V ± 10%, IOH = −4 mA; Test OUT VCCB – 0.4 VCCB – 0.2 - VVCCB = 3.3 V ± 10%, IOH = –2 mA; Test OUT1 VCCB – 0.3 VCCB – 0.15 - VCCB = 2.5 V ± 10%, IOH = –1 mA; Test OUT VCCB – 0.2 VCCB – 0.1 - VOL Low-Level Output Voltage VCCB = 5 V ± 10%, IOL = 4 mA; Test OUT - 0.2 0.4 VVCCB = 3.3 V ± 10%, IOL = 2 mA; Test OUT - 0.15 0.3 VCCB = 2.5 V ± 10%, IOL = 1 mA; Test OUT - 0.1 0.2 CMTI Common-Mode Transient Immunity Static CMTI 150 200 - kV/μs Dynamic CMTI 100 150 - kV/μs Ci Input Capacitance (1) - 2 - pF (1) Provided by bench test and design simulation TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 10 / 28 CA20230702A0

Timing Specifications − 5-V Supply All test condition is at VCCA = VCCB = 5 V ± 10%, TA = −40°C to +125°C. Typical value is in VCC = 5 V, TA = +25°C, CL = 15 pF to GND, unless otherwise noted. Parameter Conditions Min Typ Max Unit fDATA Translation Data Rate - - 150 Mpbs tPLH Propagation Delay Time - 11.5 22 ns tPHL Propagation Delay Time - 12 22 ns PWD Pulse Width Distortion (1) |tPHL– tPLH| - 0.5 5 ns tsk(CC) Channel-to-Channel Output Skew Time (1)(2) Same direction channels - - 2.5 ns tsk(PP) Channel-to-Channel Output Skew Time (1)(2) Same direction channels - - 4.5 ns tr Output Signal Rise Time (1) - 0.7 4 ns tf Output Signal Fall Time (1) - 0.7 4 ns Jitter Eye Jitter p-p (1) fdata = 100 Mbps - 340 - ps tDO Default Output Delay Time from Input Power Loss Measured from the time VCC goes below 1.7 V - 30 80 ns tSU Setup Time - 28 80 us tie Time Interval Error (1) 216− 1 PRBS data at 100 Mbps (1) - 2.4 - ns (1) Provided by bench test and design simulation. (2) tsk(CC) & tsk(PP) is the shew of delay time between the different channels of a single device or different devices switching in the same direction while operating at identical supply voltages, temperature, input signals, and loads. TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 11 / 28 CA20230702A0

Supply Current Characteristics − 5-V Supply All test condition is at VCCA = VCCB = 5 V ± 10%, TA = −40°C to +125°C. Typical value is in VCC = 5 V, TA = +25°C, CL = 15 pF to GND, unless otherwise noted. Parameter Description Supply Current Min Typ Max Unit TPT7710 Supply current - DC signal VI= 0 V (TPT7710F) VI = VCCI (TPT7710) ICCA - 0.95 2.9 mA ICCB - 2.4 2.9 VI = VCCI (TPT7710F) VI = 0 V (TPT7710) ICCA - 8.2 7.5 ICCB - 2.1 2.9 Supply current - AC signal All channels switching with square wave clock input; CL= 15 pF

1 Mbps

ICCA - 4.4 5.5 ICCB - 2.4 2.9

10 Mbps

ICCA - 4.6 6.6 ICCB - 3.7 4 100 Mbps ICCA - 6.3 8.4 ICCB - 16.4 22 (1) Provided by bench test and design simulation. (2) VCCI is the VCC of VI. TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 12 / 28 CA20230702A0

Timing Specifications − 3.3-V Supply All test condition is at VCCA = VCCB = 3.3 V ± 10%, TA = −40°C to +125°C. Typical value is in VCC = 3.3 V, TA = +25°C, CL = 15 pF to GND, unless otherwise noted. Parameter Conditions Min Typ Max Unit fDATA Translation data rate - - 150 Mpbs tPLH Propagation delay time - 12.5 22 ns tPHL Propagation delay time - 12.2 22 ns PWD Pulse width distortion (1) |tPHL – tPLH| - 0.3 5 ns tsk(CC) Channel-to-channel output skew time (1)(2) Same direction channels - - 2.5 ns tsk(PP) Channel-to-channel output skew time (1)(2) Same direction channels - - 4.5 ns tr Output signal rise time (1) - 0.7 4 ns tf Output signal fall time (1) - 0.7 4 ns Jitter Eye jitter p-p (1) fdata = 100 Mbps - 340 - ps tDO Default output delay time from input power loss Measured from the time VCC goes below 1.7 V - 30 80 ns tSU Setup time - 28 80 μs tie Time interval error (1) 216 − 1 PRBS data at 100 Mbps - 2.4 - ns (1) Provided by bench test and design simulation. (2) tsk(CC) & tsk(PP) is the shew of delay time between the different channels of a single device or different devices switching in the same direction while operating at identical supply voltages, temperature, input signals, and loads. TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 13 / 28 CA20230702A0

Supply Current Characteristics − 3.3-V Supply All test condition is at VCCA = VCCB = 3.3 V ± 10%, TA = −40°C to +125°C. Typical value is in VCC = 3.3 V, TA = +25°C, CL = 15 pF to GND, unless otherwise noted. Parameter Description Supply Current Min Typ Max Unit TPT7710 Supply current - DC signal VI = 0 V (TPT7710F) VI = VCCI (TPT7710) ICCA - 0.92 2.9 mA ICCB - 2.4 2.9 VI = VCCI (TPT7710F) VI = 0 V (TPT7710) ICCA - 8.2 7.5 ICCB - 2.1 2.9 Supply current - AC signal All channels switching with square wave clock input; CL = 15 pF ICCA - 4.3 5.1 ICCB - 2.3 2.9 ICCA - 4.4 5.8 ICCB - 3.2 3.5

100 Mbps

ICCA - 5.5 8.2 ICCB - 11 18 (1) Provided by bench test and design simulation. (2) VCCI is the VCC of VI. TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 14 / 28 CA20230702A0

Timing Specifications − 2.5-V Supply All test condition is at VCCA = VCCB = 2.5 V ± 10%, TA = −40°C to +125°C. Typical value is in VCC = 2.5 V, TA = +25°C, CL = 15 pF to GND, unless otherwise noted. Parameter Conditions Min Typ Max Unit fDATA Translation data rate - - 150 Mpbs tPLH Propagation delay time - 13.5 22 ns tPHL Propagation delay time - 12.2 22 ns PWD Pulse width distortion (1) |tPHL – tPLH| - 1.3 5 ns tsk(CC) Channel-to-channel output skew time (1)(2) Same direction channels - - 2.5 ns tsk(PP) Channel-to-channel output skew time (1)(2) Same direction channels - - 4.5 ns tr Output signal rise time (1) - 0.7 4 ns tf Output signal fall time (1) - 0.7 4 ns Jitter Eye jitter p-p (1) fdata = 100 Mbps - 350 - ps tDO Default output delay time from input power loss Measured from the time VCC goes below 1.7 V - 30 80 ns tSU Setup time - 28 80 μs tie Time interval error (1) 216 − 1 PRBS data at 100 Mbps - 2.4 - ns (1) Provided by bench test and design simulation. (2) tsk(CC) & tsk(PP) is the shew of delay time between different channels of a single device or different devices switching in the same direction while operating at identical supply voltages, temperature, input signals, and loads. TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 15 / 28 CA20230702A0

Supply Current Characteristics − 2.5-V Supply All test condition is at VCCA = VCCB = 2.5 V ± 10%, TA = −40°C to +125°C. Typical value is in VCC = 2.5 V, TA = +25°C, CL = 15 pF to GND, unless otherwise noted. Parameter Description Supply Current Min Typ Max Unit TPT7710 Supply Current - DC Signal VI = 0 V (TPT7710F) VI = VCCI (TPT7710) ICCA - 1.54 2.9 mA ICCB - 4.4 2.9 VI = VCCI (TPT7710F) VI = 0 V (TPT7710) ICCA - 10.8 7.5 ICCB - 4 2.9 Supply Current - AC Signal All channels switching with square wave clock input; CL = 15 pF ICCA - 4.3 5.1 ICCB - 2.3 2.9 ICCA - 4.3 5.5 ICCB - 3 3.3 ICCA - 4.6 6.2 ICCB - 8.9 12.5 (1) Provided by bench test and design simulation. (2) VCCI is the VCC of VI. TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 16 / 28 CA20230702A0

Figure 4. Common-Mode Transient Immunity Test Circuit

The TPT7710 family of devices is available in two-channel configurations and default output state options to enable a variety of application uses. The table below lists the device features of the TPT7710 devices. Part Number Max Data Rate Channel Direction Default Output State Package Rating Isolation TPT7710 150 Mbps 1 Forward,

0 Reverse High

TPT7710F 150 Mbps 1 Forward,

0 Reverse Low

WSOP16 5000 VRMS/ 7070 VPK WSOP8 5000 VRMS/ 7070 VPK SOP8 3750 VRMS/ 5300 VPK Device Functional Modes The table below lists the functional modes for the TPT7710 devices. VCCI VCCO Input Output Comments Power up Power up High High Normal Operation Low Low Open Default Default mode. The default is High for TPT7710 and Low for TPT7710F. Power down Power up X Default Default mode: When VCCI is unpowered, the default is High for TPT7710 and Low for TPT7710F. X Power down X Undetermined When VCCO is unpowered, a channel output is undetermined. (1) VCC I = Input-side V CCA; VCC O = Output-side V CCB; Powered up (V CC ≥ 2.25 V); Powered down (V CC ≤ 1.7 V); X = Irrelevant (2) The outputs are in the undetermined state when 1.7 V < VCCI, VCCO < 2.25 V. TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 20 / 28 CA20230702A0

Order Number Package D1 (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P0 (mm) W0 (mm) Pin1 Quadrant TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 22 / 28 CA20230702A0

Package Outline Dimensions SOP8 TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 23 / 28 CA20230702A0

1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 24 / 28 CA20230702A0

1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 25 / 28 CA20230702A0

Order Number Operating Temperature Range Package Marking Information MSL Transport Media, Quantity Eco Plan TPT7710-SO1R −40 to 125°C SOP8 T7710 MSL3 Tape and Reel, 4000 Green TPT7710F-SO1R −40 to 125°C SOP8 7710F MSL3 Tape and Reel, 4000 Green TPT7710-SOAR −40 to 125°C WSOP8 T7710 MSL3 Tape and Reel, 1000 Green TPT7710F-SOAR −40 to 125°C WSOP8 7710F MSL3 Tape and Reel, 1000 Green TPT7710-SOBR −40 to 125°C WSOP16 T7710 MSL3 Tape and Reel, 1500 Green TPT7710F-SOBR −40 to 125°C WSOP16 7710F MSL3 Tape and Reel, 1500 Green Green: 3PEAK defines "Green" to mean RoHS compatible and free of halogen substances. TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 26 / 28 CA20230702A0

IMPORTANT NOTICE AND DISCLAIMER Copyright© 3PEAK 2012-2023. All rights reserved. Trademarks. Any of the 思瑞浦 or 3PEAK trade names, trademarks, graphic marks, and domain names contained in this document /material are the property of 3PEAK. You may NOT reproduce, modify, publish, transmit or distribute any Trademark without the prior written consent of 3PEAK. Performance Information. Performance tests or performance range contained in this document/material are either results of design simulation or actual tests conducted under designated testing environment. Any variation in testing environment or simulation environment, including but not limited to testing method, testing process or testing temperature, may affect actual performance of the product. Disclaimer. 3PEAK provides technical and reliability data (including data sheets), design resources (including reference designs), application or other design recommendations, networking tools, security information and other resources "As Is". 3PEAK makes no warranty as to the absence of defects, and makes no warranties of any kind, express or implied, including without limitation, implied warranties as to merchantability, fitness for a particular purpose or non-infringement of any third- party’s intellectual property rights. Unless otherwise specified in writing, products supplied by 3PEAK are not designed to be used in any life-threatening scenarios, including critical medical applications, automotive safety-critical systems, aviation, aerospace, or any situations where failure could result in bodily harm, loss of life, or significant property damage. 3PEAK disclaims all liability for any such unauthorized use. TPT7710 1-Channel Enhanced High-Performance Digital Isolator www.3peak.com 27 / 28 CA20230702A0

1-Channel Enhanced High-Performance Digital Isolator This page intentionally left blank www.3peak.com 28 / 28 CA20230702A0