TP6001 3PEAK | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 17

Technical content

Features

 Supply Voltage: 2.1V to 6.0V  Low Supply Current: 80μA per channel  Rail to Rail Input and Output  Bandwidth: 1 MHz  Slew Rate: 0.7V/μs  Excellent EMI Suppress Performance  Offset Voltage: ±3mV Maximum  Offset Voltage Temperature Drift: 2 μV/°C  Low Noise: 27 nV/√Hz at 1kHz  High Output Capability: 100mA  –40° C to 125° C Operation Temperature Range

Applications

 Active Filters, ASIC Input or Output Amplifier  Sensor Interface  Smoke/Gas/Environment Sensors  Portable Instruments and Mobile Device

Description

The TP600X series are CMOS dual, and quad RRIO op -amps with low offset, low power and stable high frequency response. They incorporate 3PEAK’s proprietary and patented design techniques to achieve very good AC performance with 1MHz bandwidth, 0.6V/μs slew rate and l ow distortion while drawing only 80μA of quiescent current per amplifier. The input common- mode voltage range extends 300mV beyond V – and V+, and the outputs swing rail-to-rail. The TP600X family can be used as plug-in replacements for many commercially available op-amps to reduce power and improve input/output range and performance. The combination of features makes the TP600X ideal choices for motor control and portable audio amplification, sound ports, and other consumer Audio. The TP600X Op-amp is very stable, and it is capable of driving heavy capacitive loads such as those found in LCDs. The ability to swing rail -to-rail at the inputs and outputs enables designers to buffer CMOS DACs, ASICs, or other wide output swing devices in single-supply systems. Pin Configuration TP6001 5-Pin SOT23/SC70 -T and -C Suffixes TP6002 8-Pin SOIC/TSSOP/MSOP -S, -T, -TS and -V Suffixes Out A ﹢In A ﹣In A ﹢In B ﹣In B Out BA B ﹣Vs ﹢Vs TP6004 14-Pin SOIC/TSSOP -S and -T Suffixes Out A ﹢In A ﹣In A DA CB Out D ﹢In D ﹣In D Out B ﹢In B ﹣In B Out C ﹢In C ﹣In C ﹣Vs﹢Vs 1Out + In - In ﹣Vs ﹢Vs TP6001R 5-Pin SOT23 -T Suffixes 1Out + In - In + Vs - Vs TP6001U 5-Pin SOT23/SC70 -T and -C Suffixes 1+In -VS -In Out +VS

1MHz, 8 0μA, RRIO, Op Amps Table of Contents

1MHz, 8 0μA, RRIO, Op Amps

Revision History

2017/3/1 Rev.Pre Pre-Release Version 2017/8/11 Rev.0 Release Version, confirm spec limit 2017/10/28 Rev.0.01 Correct the max of Common-mode Input Voltage Range in Electrical Characteristics from (V+) - 0.1 to (V+) + 0.1. Correct Operating Temperature Range in Maximum Ratings from –45 to 125° C to –40 to 125°C. 2017/12/7 Rev 0.02 Add Package: TP6001U-CR 2018/2/1 Rev 0.03 Correct Pin configuration of TP6001R. Correct the quiescent current per amplifier in “Description” from 500uA to 80uA Order Information Order Number Operating Temperature Range Package Marking Information MSL Transport Media, Quantity TP6001-TR -40 to 125°C 5-Pin SOT23 601XX Note 2 3 Tape and Reel, 3000 TP6001-CR Note 1 -40 to 125°C 5-Pin SC70 601XX Note 2 1 Tape and Reel, 3000 TP6001R-TR -40 to 125°C 5-Pin SOT23 60RXX Note 2 3 Tape and Reel, 3000 TP6001U-TR Note 1 -40 to 125°C 5-Pin SOT23 60UXX Note 2 3 Tape and Reel, 3000 TP6001U-CR -40 to 125°C 5-Pin SC70 60UXX Note 2 1 Tape and Reel, 3000 TP6002-SR -40 to 125°C 8-Pin SOIC 6002 XXXX Note 3

3 Tape and Reel, 4000

TP6002-TSR -40 to 125°C 8-Pin TSSOP 6002 XXXX Note 3

3 Tape and Reel, 3000

TP6002-VR Note 1 -40 to 125°C 8-Pin MSOP 6002 XXXX Note 3 TP6004-SR -40 to 125° C 14-Pin SOIC 6004 XXXX Note 3

3 Tape and Reel, 2500

TP6004-TR -40 to 125° C 14-Pin TSSOP 6004 XXXX Note 3 Note 1: The sample will be ready in 1 month. Note 2: XX is the date code. Note 3: XXXX is date code.

1MHz, 8 0μA, RRIO, Op Amps Absolute Maximum Ratings Note 1 Parameters Rating Supply Voltage, (+VS)– (-VS) 7 V Input Voltage (-VS) – 0.3 to (+VS) + 0.3 Differential Input Voltage ±7V Input Current: +IN, –IN Note 2 ±10mA Output Short-Circuit Duration Note 3 Infinite Maximum Junction Temperature 150° C Operating Temperature Range –40 to 125°C Storage Temperature Range –65 to 150° C Lead Temperature (Soldering, 10 sec) 260° C Note 1: Stresses beyond those listed under Abso lute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The inputs are protected by ESD protection diodes to each power supply. If the input extends more than 300mV beyond the power supply, the input current should be limited to less than 10mA. Note 3: A heat sink may be required to keep the junction temperature below the absolute maximum. This depends on the power supply voltage and how many amplifiers are shorted. Thermal resistance varies with the amount of PC board metal connected to the package. The specified values are for short traces connected to the leads. ESD Rating Symbol Parameter Condition Minimum Level Unit HBM Human Body Model ESD MIL-STD-883H Method 3015.8 8 kV CDM Charged Device Model ESD JEDEC-EIA/JESD22-C101E 2 kV Thermal Information Package Type θJA θJC Unit 5-Pin SC70 400 ° C/W 5-Pin SOT23 250 81 ° C/W 8-Pin SOIC 158 43 ° C/W 8-Pin TSSOP 191 44 ° C/W 8-Pin MSOP 210 45 ° C/W 14-Pin SOIC 120 36 ° C/W 14-Pin TSSOP 180 35 ° C/W

1MHz, 8 0μA, RRIO, Op Amps

Electrical Characteristics

All test condition is VS = 5V, TA = 25° C, RL = 2kΩ, CL =100pF, unless otherwise noted. Symbol Parameter Conditions Min Typ Max Unit Power Supply VS Supply Voltage Range 2.1 6 V IQ Quiescent Current per Amplifier 80 130 μA PSRR Power Supply Rejection Ratio 80 100 dB Input Characteristics VOS Input Offset Voltage VCM = 0V to 3V -3 0.5 3 mV VOS TC Input Offset Voltage Drift TA = -40° C to 125° C 2 μV/° C IB Input Bias Current TA = 25 °C 1 pA TA = 85 °C 25 pA IOS Input Offset Current 1 pA CIN Input Capacitance Differential Mode 8 pF Common Mode 7 pF Av Open-loop Voltage Gain RLOAD = 10kΩ 85 110 dB VCMR Common-mode Input Voltage Range CMRR Common Mode Rejection Ratio VCM = 0V to 3V 70 100 dB Xtalk Channel Separation f = 1kHz, RL = 2kΩ 110 dB Output Characteristics VOH, VOL Maximum Output Voltage Swing RLOAD = 10kΩ 3 15 mV ISC Output Short-Circuit Current 100 mA AC Specifications GBW Gain-Bandwidth Product 1 MHz SR Slew Rate AV = 1, VOUT = 1.5V to 3.5V, CLOAD = 60pF, RLOAD = 1kΩ

0.7 V/μs

Settling Time, 0.1% AV = 1, 2V Step, CLOAD = 60pF, RLOAD = 1kΩ 3.5 μs Settling Time, 0.01% 4.8 μs PM Phase Margin RLOAD = 1kΩ, CLOAD = 60pF 60 ° GM Gain Margin RLOAD = 1kΩ, CLOAD = 60pF 15 dB Noise Performance EN Input Voltage Noise f = 0.1Hz to 10Hz 8 μVPP eN Input Voltage Noise Density f = 1kHz 27 nV/√Hz iN Input Current Noise f = 1kHz 2 fA/√Hz THD+N Total Harmonic Distortion and Noise f = 1kHz, AV =1, RL = 2kΩ, VOUT = 1Vp-p 0.003 %

Application Information

Low Supply Voltage and Low Power Consumption The TP600X family of operational amplifiers can operate with power supply voltages from 2.1 V to 6.0 V. Each amplifier draws only 80 μA quiescent current. The low supply voltage capability and low supply current are ideal for portable applications demanding high capacitive load driving capability and stable wide bandwidth. The TP600X family is optimized for wide bandwidth low power applications. They have an industry leading high GBWP to power ratio and are unity gain stable for any capacitive load. When th e load capacitance increases, the increased capacitance at the output pushed the non -dominant pole to lower frequency in the open loop frequency response, lowering the phase and gain margin. Higher gain configurations tend to have better capacitive drive capability than lower gain configurations due to lower closed loop bandwidth and hence higher phase margin. Ground Sensing and Rail to Rail Output The TP600X family has excellent output drive capability, delivering over 100 mA of output drive current. The output stage is a rail-to- rail topology that is capable of swinging to within 10mV of either rail. Since the inputs can go 300 mV be yond either rail, the op-amp can easily perform ‘true ground’ sensing. The maximum output current is a function of total supply voltage. As the supply voltage to the amplifier increases, the output current capability also increases. Attention must be paid to keep the junction temperature of the IC below 150° C when the output is in continuous short-circuit. The output of the amplifier has reverse-biased ESD diodes connected to each supply. The output should not be forced more than 0.5V beyond either supply, otherwise current will flow through these diodes. Driving Large Capacitive Load The TP600X family of OPA is designed to drive large capacitive loads. Refer to Typical Performance Characteristics for “Phase Margin vs. Load Capacitance”. As always, larger l oad capacitance decreases overall phase margin in a feedback system where internal frequency compensation is utilized. As the load capacitance increases, the feedback loop’s phase margin decreases, and the closed-loop bandwidth is reduced. This produces gain peaking in the frequency response, with overshoot and ringing in output step response. The unity-gain buffer (G = +1V/V) is the most sensitive to large capacitive loads. When driving large capacitive loads with the TP600X OPA family (e.g., > 200 pF wh en G = +1V/V), a small series resistor at the output (RISO in Figure 3) improves the feedback loop’s phase margin and stability by making the output load resistive at high er frequencies. Vin Vout Cload Riso

1MHz, 8 0μA, RRIO, Op Amps Tape and Reel Information Order Number Package D1 W1 A0 B0 K0 P0 W0 Pin1 Quadrant

1MHz, 8 0μA, RRIO, Op Amps Package Outline Dimensions SC70-5 /SOT-353 SOT23-5 Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max A 1.050 1.250 0.041 0.049 A1 0.000 0.100 0.000 0.004 A2 1.050 1.150 0.041 0.045 b 0.300 0.400 0.012 0.016 C 0.100 0.200 0.004 0.008 D 2.820 3.020 0.111 0.119 E 1.500 1.700 0.059 0.067 E1 2.650 2.950 0.104 0.116 e 0.950TYP 0.037TYP e1 1.800 2.000 0.071 0.079 L 0.700REF 0.028REF L1 0.300 0.460 0.012 0.024 θ 0° 8° 0° 8° Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max A 0.900 1.100 0.035 0.043 A1 0.000 0.100 0.000 0.004 A2 0.900 1.000 0.035 0.039 b 0.150 0.350 0.006 0.014 C 0.080 0.150 0.003 0.006 D 2.000 2.200 0.079 0.087 E 1.150 1.350 0.045 0.053 E1 2.150 2.450 0.085 0.096 e 0.650TYP 0.026TYP e1 1.200 1.400 0.047 0.055 L 0.525REF 0.021REF L1 0.260 0.460 0.010 0.018 θ 0° 8° 0° 8°

1MHz, 8 0μA, RRIO, Op Amps D b E e θ C SOP-8 Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max A1 0.100 0.250 0.004 0.010 A2 1.350 1.550 0.053 0.061 b 0.330 0.510 0.013 0.020 C 0.190 0.250 0.007 0.010 D 4.780 5.000 0.188 0.197 E 3.800 4.000 0.150 0.157 E1 5.800 6.300 0.228 0.248 e 1.270 TYP 0.050 TYP L1 0.400 1.270 0.016 0.050 θ 0° 8° 0° 8°

1MHz, 8 0μA, RRIO, Op Amps TSSOP-8 Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max D 2.900 3.100 0.114 0.122 E 4.300 4.500 0.169 0.177 b 0.190 0.300 0.007 0.012 c 0.090 0.200 0.004 0.008 E1 6.250 6.550 0.246 0.258 A 1.200 0.047 A2 0.800 1.000 0.031 0.039 A1 0.050 0.150 0.002 0.006 e 0.65(BSC) 0.026（BSC） L 0.500 0.700 0.020 0.028 H 0.25(BSC) 0.01（BSC） θ 1° 7° 1° 7°

1MHz, 8 0μA, RRIO, Op Amps MSOP-8 Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max A 0.800 1.200 0.031 0.047 A1 0.000 0.200 0.000 0.008 A2 0.760 0.970 0.030 0.038 b 0.30 TYP 0.012 TYP C 0.15 TYP 0.006 TYP D 2.900 3.100 0.114 0.122 e 0.65 TYP 0.026 E 2.900 3.100 0.114 0.122 E1 4.700 5.100 0.185 0.201 L1 0.410 0.650 0.016 0.026 θ 0° 6° 0° 6° e E A D L1 L2 L R θ b

1MHz, 8 0μA, RRIO, Op Amps SOP-14 Symbol Dimensions In Millimeters MIN NOM MAX A 1.35 1.60 1.75 A1 0.10 0.15 0.25 A2 1.25 1.45 1.65 A3 0.55 0.65 0.75 b 0.36 0.49 b1 0.35 0.40 0.45 c 0.16 0.25 c1 0.15 0.20 0.25 D 8.53 8.63 8.73 E 5.80 6.00 6.20 E1 3.80 3.90 4.00 e 1.27 BSC L 0.45 0.60 0.80 L1 1.04 REF L2 0.25 BSC R 0.07 R1 0.07 h 0.30 0.40 0.50 θ 0° 8° θ1 6° 8° 10° θ2 6° 8° 10° θ3 5° 7° 9° θ4 5° 7° 9°

1MHz, 8 0μA, RRIO, Op Amps TSSOP-14 Symbol Dimensions In Millimeters MIN TYP MAX A - - 1.20 A1 0.05 - 0.15 A2 0.90 1.00 1.05 b 0.20 - 0.28 c 0.10 - 0.19 D 4.86 4.96 5.06 E 6.20 6.40 6.60 E1 4.30 4.40 4.50 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF L2 0.25 BSC R 0.09 - - θ 0° - 8° E e A D L1 L2 L R θ c

1MHz, 8 0μA, RRIO, Op Amps 3PEAK and the 3PEAK logo are registered trademarks of 3PEAK INCORPORATED. All other trademarks are the property of their respective owners.