TP2271

TP2271 3PEAK | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 16

Technical content

Features

 Gain-bandwidth Product: 7MHz  High Slew Rate: 20V/μs  High EMIRR: 84dB at 900MHz  Low Noise: 19 nV/√Hz(f= 1kHz)  Wide Supply Range: 2.7V to 36V  Low Offset Voltage: 1.0mV Maximum  Low Input Bias Current: 3pA Typical  Below-Ground (V-) Input Capability to -0.3V  Rail-to-Rail Output Voltage Range  High Output Current: 80mA (2.0V Drop)  Unit Gain Stable  3mm*2mm DFN Package for TP2274  –40° C to 125° C Operation Range  Robust 3kV – HBM and 2kV – CDM ESD Rating

Applications

 Digital Servo Control Loops  Machine and Motion Control Devices  Photodiode Pre-amp  Industrial Process Control  Temperature Measurements  Strain Gage Amplifier  Medical Instrumentation Pin Configuration (Top View) TP2272 8-Pin SOIC/MSOP/TSSOP (-S, -V and -TS Suffixes) Out A ﹢In A ﹣In A ﹢In B ﹣In B Out BA B ﹣Vs ﹢Vs TP2274 14-Pin SOIC/TSSOP/DFN (-S , -T and -F Suffixes) Out A ﹢In A ﹣In A DA CB Out D ﹢In D ﹣In D Out B ﹢In B ﹣In B Out C ﹢In C ﹣In C ﹣Vs﹢Vs TP2271 8-Pin SOIC (-S Suffix) Out TP2271 5-Pin SOT23 (-T Suffix) NC ﹢In ﹣In ﹣Vs ﹢Vs NC NC 1Out +In -In ﹣Vs ﹢Vs

Description

The TP2271/TP2272/TP2274 are EMI Hardened 36V CMOS op-amps featuring EMIRR of 84dB at 900MHz. The devices are unity gain stable with 100pF capacitive load and high-speed with a wide 7MHz bandwidth and 20V/μs high slew rate, which make s the devices appropriated for I/V converters. The rail-to-rail output swing and input range that includes V– makes the TP227x ideal choices for interfacing to modern, single-supply and precision data converters. The TP227x op-amps offer lower noise, offset voltage, offset drift over temperature and bias current . In addition, the devices have better common -mode rejection and slew rates. The T P227x family, exhibiting high input impedance and low noise, is excellent for small signal conditioning for high impedance sources, such as piezoelectric transducers. Because of the micro power dissipation levels, the devices work well in hand held monitoring and remote sensing applications. The TP2271 is single channel version available in 8-pin SOIC and 5-pin SOT23 packages. The TP2272 is dual channel version available in 8 -pin SOIC and MSOP packages. The TP2274 is quad channel version available in 14-pin SOIC, TSSOP and DFN packages. 3PEAK and the 3PEAK logo are registered trademarks of 3PEAK INCORPORATED. All other trademarks are the property of their respective owners. EMIRR IN+ vs. Frequency 400 4000 EMIRR IN+(dB) Frequency (MHz)

2 REV C.02 www.3peakic.com.cn TP2271 / TP2272 / TP2274 36V Single supply, 7MHz Bandwidth, RRO Op-amps Order Information Model Name Order Number Package MSL Transport Media, Quantity Marking Information TP2271 TP2271-SR 8-Pin SOIC MSL 3 Tape and Reel, 4,000 TP2271 TP2271-TR 5-Pin SOT23 MSL 3 Tape and Reel, 3,000 E22 TP2272 TP2272-SR 8-Pin SOIC MSL 3 Tape and Reel, 4,000 TP2272 TP2272-VR 8-Pin MSOP MSL 3 Tape and Reel, 3,000 TP2272 TP2272-TSR 8-Pin TSSOP MSL 1 Tape and Reel, 3,000 TP2272 TP2272L1-SR 8-Pin SOIC MSL 1 Tape and Reel, 4,000 TP2272 TP2274 TP2274-SR 14-Pin SOIC MSL 3 Tape and Reel, 2,500 TP2274 TP2274-TR 14-Pin TSSOP MSL 3 Tape and Reel, 3,000 TP2274 TP2274-FR 14-Pin DFN MSL 3 Tape and Reel, 3,000 2274 Absolute Maximum Ratings Note 1 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolut e Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The op amp supplies must be established simultaneously, with, or before, the application of any input signals. Note 3: The inputs are protected by ESD protection diodes to e ach power supply. If the input extends more than 500mV beyond the power supply, the input current should be limited to less than 10mA. Note 4: The differential input voltage must be in the range of Input Voltage: V– – 0.3 to V+ + 0.3 V Note 5: A heat sink may be required to keep the junction temperature below the absolute maximum. This depends on the power supply voltage and how many amplifiers are shorted. Thermal resistance varies with the amount of PC board metal connected to the package. The specified values are for short traces connected to the leads. ESD, Electrostatic Discharge Protection Symbol Parameter Condition Minimum Level Unit HBM Human Body Model ESD MIL-STD-883H Method 3015.8 3 kV CDM Charged Device Model ESD JEDEC-EIA/JESD22-C101E 2 kV Thermal Resistance Package Type θJA θJC Unit Package Type θJA θJC Unit 5-Pin SOT23 250 81 °C /W 14-Pin SOIC 120 36 °C /W 8-Pin SOIC 158 43 °C /W 14-Pin TSSOP 180 35 °C /W 8-Pin MSOP 210 45 °C /W 14-Pin DFN 100 34 ° C/W 8-Pin TSSOP 191 44 °C /W

36V Single supply, 7MHz Bandwidth, RRO Op-amps www.3peakic.com.cn REV C.02

Electrical Characteristics

The specifications are at TA = 27° C. VS = ±15V, VCM = 0V, RL = 2kΩ, CL =100pF.Unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VOS Input Offset Voltage VOS TC Input Offset Voltage Drift -40°C to 125°C 2 μV/° C IB Input Bias Current TA = 27 °C 3 pA TA = 85 °C 250 pA TA = 125 °C 7.7 nA IOS Input Offset Current 1 pA Vn Input Voltage Noise f = 0.1Hz to 10Hz 2.35 μVRMS en Input Voltage Noise Density f = 1kHz 19 nV/√Hz CIN Input Capacitance Differential Common Mode 4 2.5 pF CMRR Common Mode Rejection Ratio VCM = -14.5V to 13V 95 126 dB VCM Common-mode Input Voltage Range V– -0.3 V+-2.0 V PSRR Power Supply Rejection Ratio 95 130 dB AVOL Open-Loop Large Signal Gain RLOAD = 2kΩ 95 120 dB VOL, VOH Output Swing from Supply Rail RLOAD = 100kΩ 50 mV ROUT Closed-Loop Output Impedance G = 1, f =1kHz, IOUT = 0 0.01 Ω RO Open-Loop Output Impedance f = 1kHz, IOUT = 0 125 Ω ISC Output Short-Circuit Current Sink or source current 80 mA VS Supply Voltage 2.7 36 V IQ Quiescent Current per Amplifier 900 1500 μA PM Phase Margin RLOAD = 2kΩ, CLOAD = 100pF 60 ° GM Gain Margin RLOAD = 2kΩ, CLOAD = 100pF 8 dB GBWP Gain-Bandwidth Product f = 1kHz 7 MHz SR Slew Rate AV = 1, VOUT = 0V to 10V, CLOAD = 100pF, RLOAD = 2kΩ 20 V/μs FPBW Full Power Bandwidth Note 1 210 kHz tS Settling Time, 0.1% Settling Time, 0.01% AV = –1, 10V Step 0.8 1 μs THD+N Total Harmonic Distortion and Noise f = 1kHz, AV =1, RL = 2kΩ, VOUT = 3.5VRMS 0.0001 % Xtalk Channel Separation f = 1kHz, RL = 2kΩ 110 dB Note 1: Full power bandwidth is calculated from the slew rate FPBW = SR/π • VP-P

4 REV C.02 www.3peakic.com.cn TP2271 / TP2272 / TP2274 36V Single supply, 7MHz Bandwidth, RRO Op-amps Typical Performance Characteristics VS = ± 15V, VCM = 0V, RL = Open, unless otherwise specified. Offset Voltage Production Distribution Unity Gain Bandwidth vs. Temperature 100 120 140 160 180 200 Population Offset Voltage(mV) -50 0 50 100 150 GBW(MHz) Temp(℃) Open-Loop Gain and Phase CMRR vs. Input Common Mode Voltage -20 130 180 1 10 100 1k 10k 100k 1M 10M 100M Gain(dB) & Phase Frequency (Hz) Phase Open Loop Gain 100 150 -15 -12 -9 -6 -3 0 3 6 9 12 15 CMRR(dB) Common Mode Voltage (V) Positive Output Swing vs. Load Current Negative Output Swing vs. Load Current VOUT(V) IOUT(A) 125℃ 27℃ -40℃ 0.5 1.5 2.5 3.5 VOUT(V) IOUT(A) 125℃ 27℃ -40℃

36V Single supply, 7MHz Bandwidth, RRO Op-amps www.3peakic.com.cn REV C.02 Typical Performance Characteristics VS = ± 15V, VCM = 0V, RL = Open, unless otherwise specified. (Continued) Common Mode Rejection Ratio CMRR vs. Frequency 100 150 -15 -12 -9 -6 -3 0 3 6 9 12 15 CMRR(dB) Common Mode Voltage (V) 100 120 140 0.1 10 1k 100k 10M CMRR(dB) Frequency (Hz) Quiescent Current vs. Temperature Short Circuit Current vs. Temperature 0.2 0.4 0.6 0.8 1.2 1.4 -50 0 50 100 150 Supply Current (mA) Temperature (℃) -50 0 50 100 ishort(mA) Temperature (C) Isorce Isink Power-Supply Rejection Ratio Quiescent Current vs. Supply Voltage 100 120 140 0.1 10 1k 100k 10M PSRR(dB) Frequency (Hz) 0.85 0.86 0.87 0.88 0.89 0.9 0.91 0.92 0.93 0 2 4 6 8 10 12 14 Supply Current (mA) Supply Voltage (V)

6 REV C.02 www.3peakic.com.cn TP2271 / TP2272 / TP2274 36V Single supply, 7MHz Bandwidth, RRO Op-amps Typical Performance Characteristics VS = ± 15V, VCM = 0V, RL = Open, unless otherwise specified. (Continued) Power-Supply Rejection Ratio vs. Temperature CMRR vs. Temperature 116 118 120 122 124 -50 0 50 100 PSRR (dB) Temperature (C) 110 112 114 116 118 120 122 124 126 128 130 132 -50 0 50 100 CMRR(dB) Temperature (C) EMIRR IN+ vs. Frequency Large-Scale Step Response 400 4000 EMIRR IN+(dB) Frequency (MHz) Time (50μs/div) Output Voltage (2V/div) G = +1 RL=10KΩ Negative Over-Voltage Recovery Positive Over-Voltage Recovery G = +1 RL=10KΩ 2V/div Time (0.5μs/div) 2V/div G = +10 ±V= ±2.5V 2V/div Time (0.5μs/div) 5V/div G = +10 ±V= ±15V

36V Single supply, 7MHz Bandwidth, RRO Op-amps www.3peakic.com.cn REV C.02 Pin Functions -IN: Inverting Input of the Amplifier. Voltage range of this pin can go from V– to (V+ - 2.0V). +IN: Non-Inverting Input of Amplifier. This pin has the same voltage range as –IN. V+ or +VS: Positive Power Supply. Typically the voltage is from 2.7V to 36V. Split supplies are possible as long as the voltage between V+ and V – is between 2.7V and 36V. A bypass capacitor of 0.1μF as close to the part as possible should be used between power supply pins or between supply pins and ground. V– or –VS: Negative Power Supply. It is normally tied to ground. It can also be tied to a voltage other than ground as long as the voltage between V+ and V– is from 2.7V to 36V. If it is not connected to ground, bypass it with a capacitor of 0.1μF as close to the part as possible. OUT: Amplifier Output. The voltage range extends to within milli-volts of each supply rail. N/C: No connection. The exposed thermal pad of DFN package should be left floated. Operation The TP227x op-amps have input signal range from V– to (V+ – 2.0V). The output can extend all the way to the supply rails. The input stage is comprised of a PMOS differential amplifier. The Class-AB control buffer and output bias stage uses a proprietary compensation technique to take full advantage of the process technology to drive very high capacitive loads. This is evident from the transient over shoot measurement plots in the Typical Performance Characteristics. Applications Information EMI Harden The EMI hardening makes the TP2271/2272/2274 a must for almost all op amp applications. Most applications are exposed to Radio Frequency (RF) signals such as the signals transmitted by mobile phones or wireless computer peripherals. The TP2271/2272/2274 will effectively reduce disturbances caused by RF signals to a level that will be hardly noticeable. This again reduces the need for add itional filtering and shielding Using this EMI resistant series of op amps will thus reduce the number of components and space needed for applications that are affected by EMI, and will help applications, not yet identified as possible EMI sensitive, to be more robust for EMI. Wide Supply Voltage The TP2271/2272/2274 operational amplifiers can operate with power supply voltages from 2.7V to 36V. Each amplifier draws 0.8mA quiescent current at 36V supply voltage. The TP2271/2272/2274 is optimized for wide bandwidth low power applications. They have a n industry leading high GBW to power ratio and the GBW remains nearly constant over specified temperature range. Low Input Bias Current The TP2271/2272/2274 is a CMOS OPA family and features very low input bias current in pA range. The low input bias current allows the amplifiers to be used in applications with high resistance sources. Care must be taken to minimize PCB Surface Leakage. See below section on “PCB Surface Leakage” for more details. PCB Surface Leakage In applications where low input bias current is critical, Printed Circuit Board (PCB) surface leakage effects need to be considered. Sur face leakage is caused by humidity, dust or other contamination on the board. Under low humidity conditions, a typical resistance between nearby traces is 1012Ω. A 5V difference would cause 5pA of current to flow,

8 REV C.02 www.3peakic.com.cn TP2271 / TP2272 / TP2274 36V Single supply, 7MHz Bandwidth, RRO Op-amps which is greater than the TP2271/2272/2274 OPA’s input bias current at +27°C (± 3pA, typical). It is recommended to use multi-layer PCB layout and route the OPA’s -IN and +IN signal under the PCB surface. The effective way to reduce surface leakage is to use a guard ring around sensitive pins (or traces). The guard ring is biased at the same voltage as the sensitive pin. An example of this type of layout is shown in Figure 1 for Inverting Gain application. 1. For Non-Inverting Gain and Unity-Gain Buffer: a) Connect the non-inverting pin (VIN+) to the input with a wire that does not touch the PCB surface. b) Connect the guard ring to the inverting input pin (VIN–). This biases the guard ring to the Common Mode input voltage. 2. For Inverting Gain and Trans-impedance Gain Amplifiers (convert current to voltage, such as photo detectors): a) Connect the guard ring to the non-inverting input pin (VIN+). This biases the guard ring to the same reference voltage as the op-amp (e.g., VDD/2 or ground). b) Connect the inverting pin (VIN–) to the input with a wire that does not touch the PCB surface. VIN+ VIN- +VSGuard Ring Figure 1 The Layout of Guard Ring Ground Sensing and Rail to Rail Output The TP2271/2272/2274 family has excellent output drive capability. It drives 2k load directly with good THD performance. The output stage is a rail-to-rail topology that is capable of swinging to within 50mV of either rail. The maximum output current is a function of total supply voltage. As the supply voltage to the amplifier increases, the output current capability also increases. Attention must be paid to keep the junction temperature of the IC below 150° C when the output is in continuous short-circuit. The output of the amplifier has reverse-biased ESD diodes connected to each supply. The output should not be forced more than 0.3V beyond either supply, otherwise current will flow through these diodes. Power Supply Layout and Bypass The TP2271/2272/2274 OPA’s power supply pin (V DD for single-supply) should have a local bypass capacitor (i.e., within 100mm to provide large, slow currents. This bulk capacitor can be shared with other analog parts. Ground layout improves performance by decreasing the amount of stray capacitance and noise at the OPA’s inputs and outputs. To decrease stray capacitance, minimize PC board lengths and resistor leads, and place external components as close to the op amps’ pins as possible. Proper Board Layout To ensure optimum performance at the PCB level, care must be taken in the design of the board layout. To avoid leakage currents, the surface of the board sh ould be kept clean and free of moisture. Coating the surface creates a barrier to moisture accumulation and helps reduce parasitic resistance on the board. Keeping supply traces short and properly bypassing the power supplies minimizes power supply disturb ances due to output current variation, such as when driving an ac signal into a heavy load. Bypass capacitors should be connected as closely as possible to the device supply pins. Stray capacitances are a concern at the outputs and the inputs of the amplifier. It is recommended that signal traces be kept at least 5mm from supply lines to minimize coupling. A variation in temperature across the PCB can cause a mismatch in the Seebeck voltages at solder joints and other points where dissimilar metals are in c ontact, resulting in thermal voltage errors. To minimize these thermocouple effects, orient resistors so heat sources warm both ends equally. Input signal paths should contain matching numbers and types of components, where possible to match the number and type of thermocouple junctions. For example, dummy components such as zero value resistors can be used to match real resistors in the opposite input path. Matching components should be located in close proximity and should be oriented in the same manner. Ensure leads

36V Single supply, 7MHz Bandwidth, RRO Op-amps www.3peakic.com.cn REV C.02 are of equal length so that thermal conduction is in equilibrium. Keep heat sources on the PCB as far away from amplifier input circuitry as is practical. The use of a ground plane is highly recommended. A ground plane reduces EMI noise and al so helps to maintain a constant temperature across the circuit board. TP2272 VIN 3000pF 22kΩ 22kΩ 2.7kΩ 10kΩ R3 C3 100pF VO 2000pF 20pf kHz Three-Pole Low-Pass Filter

10 REV C.02 www.3peakic.com.cn TP2271 / TP2272 / TP2274 36V Single supply, 7MHz Bandwidth, RRO Op-amps Package Outline Dimensions SOT23-5 Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max A 1.050 1.250 0.041 0.049 A1 0.000 0.100 0.000 0.004 A2 1.050 1.150 0.041 0.045 b 0.300 0.400 0.012 0.016 C 0.100 0.200 0.004 0.008 D 2.820 3.020 0.111 0.119 E 1.500 1.700 0.059 0.067 E1 2.650 2.950 0.104 0.116 e 0.950TYP 0.037TYP e1 1.800 2.000 0.071 0.079 L 0.700REF 0.028REF L1 0.300 0.460 0.012 0.024 θ 0° 8° 0° 8°

36V Single supply, 7MHz Bandwidth, RRO Op-amps www.3peakic.com.cn REV C.02 D b E e θ C Package Outline Dimensions SO-8 (SOIC-8) Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max A1 0.100 0.250 0.004 0.010 A2 1.350 1.550 0.053 0.061 b 0.330 0.510 0.013 0.020 C 0.190 0.250 0.007 0.010 D 4.780 5.000 0.188 0.197 E 3.800 4.000 0.150 0.157 E1 5.800 6.300 0.228 0.248 e 1.270 TYP 0.050 TYP L1 0.400 1.270 0.016 0.050 θ 0° 8° 0° 8°

12 REV C.02 www.3peakic.com.cn TP2271 / TP2272 / TP2274 36V Single supply, 7MHz Bandwidth, RRO Op-amps Package Outline Dimensions MSOP-8 Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max A 0.800 1.200 0.031 0.047 A1 0.000 0.200 0.000 0.008 A2 0.760 0.970 0.030 0.038 b 0.30 TYP 0.012 TYP C 0.15 TYP 0.006 TYP D 2.900 3.100 0.114 0.122 e 0.65 TYP 0.026 E 2.900 3.100 0.114 0.122 E1 4.700 5.100 0.185 0.201 L1 0.410 0.650 0.016 0.026 θ 0° 6° 0° 6° e E A D L1 L2 L R θ b

36V Single supply, 7MHz Bandwidth, RRO Op-amps www.3peakic.com.cn REV C.02 TSSOP-8 Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max D 2.900 3.100 0.114 0.122 E 4.300 4.500 0.169 0.177 b 0.190 0.300 0.007 0.012 c 0.090 0.200 0.004 0.008 E1 6.250 6.550 0.246 0.258 A 1.200 0.047 A2 0.800 1.000 0.031 0.039 A1 0.050 0.150 0.002 0.006 e 0.65(BSC) 0.026（BSC） L 0.500 0.700 0.020 0.028 H 0.25(BSC) 0.01（BSC） θ 1° 7° 1° 7°

14 REV C.02 www.3peakic.com.cn TP2271 / TP2272 / TP2274 36V Single supply, 7MHz Bandwidth, RRO Op-amps Package Outline Dimensions TSSOP-14 Symbol Dimensions In Millimeters MIN TYP MAX A - - 1.20 A1 0.05 - 0.15 A2 0.90 1.00 1.05 b 0.20 - 0.28 c 0.10 - 0.19 D 4.86 4.96 5.06 E 6.20 6.40 6.60 E1 4.30 4.40 4.50 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF L2 0.25 BSC R 0.09 - - θ 0° - 8° E e A D L1 L2 L R θ c

36V Single supply, 7MHz Bandwidth, RRO Op-amps www.3peakic.com.cn REV C.02 θ e b E1 E D A A2 L Package Outline Dimensions SO-14 (SOIC-14) Symbol Dimensions In Millimeters MIN TYP MAX A 1.35 1.60 1.75 A1 0.10 0.15 0.25 A2 1.25 1.45 1.65 b 0.36 0.49 D 8.53 8.63 8.73 E 5.80 6.00 6.20 E1 3.80 3.90 4.00 e 1.27 BSC L 0.45 0.60 0.80 L1 1.04 REF L2 0.25 BSC θ 0° 8°

16 REV C.02 www.3peakic.com.cn TP2271 / TP2272 / TP2274 36V Single supply, 7MHz Bandwidth, RRO Op-amps Package Outline Dimensions DFN-14 Symbol Dimensions In Millimeters MIN TYP MAX A 0.7 0.75 0.8 A1 0.02 0.05 b 0.15 0.18 0.25 c 0.18 0.20 0.25 D 2.90 3.00 3.10 D2 2.40 2.50 2.60 e 0.40 Nd 2.40 E 1.90 2.00 2.10 E2 0.70 0.80 0.90 L 0.30 0.35 0.40 H 0.20 0.25 0.30