TMCC160

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 39

Technical content

motionCookie SYSTEM IN A PACKAGE motionCookie™ © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com TMCC160 DATASHEET Block Diagram Microcontroller UART CAN SPI0 SPI1 AIN Gatedriver PWM DIAG Current TMCC160 ABN HALL Ref. Switches I_U, I_V DC/DC (3.3V) Power Supply VM Power Bridge Motor V ABN HALL I_U, I_V U W Figure 1: TMCC160 System Block Diagram Features & Benefits Integrated BLDC or PMSM Servo Controller Integrated Gate Driver up to 1A Gate Current Voltage Range 7…24V Integrated FOC Controller UART, CAN or SPI Interface Hall Interface ABN Incremental Encoder Interface Integrated Switching Regulator

Description

The TMCC160 is a ready to use PMSM/ BLDC motor controller in a miniaturized 12x17mm² system in a package. It integrates a powerful programmed microcontroller with efficient state of the art commutation algorithm, gate driver, different interface options as well as a step down converter which generates the digital power supply, measurement and diagnostic features. Integrated motionCookie™ microsystem with 3-Phase BLDC/PMSM gate driver for up to 24V and 1A gate current with a complete servocontroller software stack.

Applications

Pump, Fan Applications Industrial Automation Medical, Lab Automation CNC Machines E-Bikes Battery Powered Devices

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

1 Table of Contents

4.1 Gate Driver Charge Pump (TMC6130) 8

4.5.1 Direct Coil Current Measurement 15

4.5.2 Recommended Schematic for Direct

4.5.11 Power Supply Filtering

motionCookie SYSTEM IN A PACKAGE motionCookie™ © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com PRODUCT DETAILS

2 Pin Assignments

TMCC160 has two pad sizes. The pads on the edges measure 0.43mm x 0.43mm with 1mm pitch. The inner pads measure 1.93mm x 1.93mm. Please refer to chapter TMCC160 Package Footprint for further information about the package dimensions.

2.1 Package Pin Numbering

CAN_RXD CAN_TXD EXTAL XTAL Figure 1 TMCC160 pin assignments / bottom view

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

2.2 Package Pin Description

1 Out (D) RS485_DIR RS485 transceiver direction output. 2 In (D) CSN_SPI1 SPI1 chip select input (low active) (slave interface). 3 In (D) SCLK_SPI1 SPI1 serial clock input (slave interface). 4 In (D) MOSI_SPI1 SPI1 serial input (slave interface). 5 Out (D) MISO_SPI1 SPI1 serial output (slave interface). 6 In (A) I_V Analog current sense amplifier input for PMSM phase V. 7 In (A) I_U Analog current sense amplifier input for PMSM phase U. 8 In (A) TEMP Analog input for temperature measurement. 9 In (A) AIN General purpose analog input. 10 Out (D) Brake PWM output for brake chopper circuit. 11 In (D) REFL Left reference switch input. 12 In (D) REFR Right reference switch input. 13 Out DA 3.3V switch regulator diode anode. 14 Out SW 3.3V switch regulator switch cathode. 15 Out LS1 Low side N-channel MOSFET gate output phase 1 (U). 16 In BM1 MOSFET bridge output phase 1 (U). 17 Out HS1 High side N-channel MOSFET gate output phase 1 (U). 18 Out HS3 High side N-channel MOSFET gate output phase 3 (W). 19 In BM3 MOSFET bridge output phase 3 (W). 20 Out LS3 Low side N-channel MOSFET gate output phase 3 (W). 21 Out VCP_REG Gate driver linear regulator output. Connect 4.7µF capacitor. 22 In VCP Gate driver charge pump input. 23 Out VCP_SW Gate driver charge pump output. 24 In (D) HALL_1 Hall sensor 1 input. 25 In (D) HALL_2 Hall sensor 2 input. 26 In (D) HALL_3 Hall sensor 3 input. 27 In (D) ENC_N Encoder N (index) input. 28 In (D) ENC_B Encoder B input. 29 In (D) ENC_A Encoder A input. 30 Out (D) MOSI_SPI0 SPI0 serial output (EEPROM master). 31 In (D) MISO_SPI0 SPI0 serial input (EEPROM master). 32 Out (D) SCLK_SPI0 SPI0 serial clock output (EEPROM master). 33 Out (D) CSN_SPI0 SPI0 chip select output (low active) (EEPROM master). 34 IO (D) ENABLE Motor driver enable (high active). ENABLE signal is also connected to the internal µC. Please connect ENABLE pin only to open drain outputs. 35 Out XTAL Crystal oscillator output. 36 In EXTAL Crystal oscillator input. 37 Out (D) CAN_TXD CAN interface output. Connect to CAN transceiver.

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com Package Pin Description Pad Number Type Name Function 38 In (D) CAN_RXD CAN interface input. Connect to CAN transceiver. 39 Out (D) TXD UART output. Connect to RS232/RS485 transceiver. 40 In (D) RXD UART input. Connect to RS232/RS485 transceiver. 41 In (D) SWDCLK Please do not connect. 42 IO (D) SWDIO Please do not connect. 43 VM Motor supply voltage. 44 In VCC 3.3V digital supply voltage. 45 GND System ground connection. 46 GND System ground connection. 47 Out LS2 Low side N-channel MOSFET gate output phase 2 (V). 48 In BM2 MOSFET bridge output phase 2 (V). 49 Out HS2 High side N-channel MOSFET gate output phase 2 (V).

50 In (A) RS+ Positive current sense input for single shunt

measurement.

51 In (A) RS- Negative current sense input for single shunt

measurement. Table Key: (D): digital IO, (A): analog IO

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

2.3 Wide Range of Control Algorithms

The TMCC160 is a ready to use PMSM/ BLDC motor controller in a miniaturized 12x 17mm² package. It integrates a powerful programmed micro controller with efficient state of the art commutation algorithm, gate driver, measurement and diagnostic features, different interface options as well as a step down converter which generates the digital power supply. TMCC160 supports state of the art field oriented control algorithm (FOC) using hall or encoder signals for PMSM motors as well as block hall commutation (six step mode) for BLDC motors . Current-, velocity - and position controller are implemented for all commutation modes. They can be parameterized via the installed TMCL protocol. Only few external hardware components are needed to build a complete servo drive without spending time developing complicated control and communication software. With the programmed operating system, TMCL, it is possible to directly connect a host PC to the TMCC160 via one of the supported interface connections. All parameters for motion control and global functions can be configured by only reading or writing registers. i Software customization and custom package labeling are available upon request. TMCC supports FOC and six-step mode Scope of TMCL Operating System

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

3 System Overview

3.1 Block Diagram

Ref. Switches I_U, I_V DC/DC (3.3V) Power Supply VM Power Bridge Motor V ABN HALL I_U, I_V U W Figure 2: TMCC160 System Block Diagram

3.2 System Architecture

Only a few external components are ne eded to build a complete closed -loop system with maximum flexibility. To interconnect TMCC160 with a host PC or microcontroller , the following interfaces are available : UART(RS232, RS485), CAN, SPI. An analog input supports simple standalone applications. To avoid power supply overshoots during deceleration/ energy feedback from the motor, TMCC160 provides a brake chopper output which can be connected to a low side N -channel MOSFET. The brake chopper duty cycle will be automatically controlled depending on the supply voltage. TMCL programs can be stored in an external EEPROM. Programs can be automatically executed after power up or triggered from the host system. Avoiding Power Overshoots TMCL storage in external EEPROM

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

3.3 Hall-Sensor Configuration

For applications with reduced requirements concerning positioning accuracy and low speed behavior a hall-sensor configuration is the most cost efficient option. Most BLDC/ PMSM motors already include hall-sensors for commutation. Microcontroller UART CAN SPI1 AIN Gatedriver PWM DIAG Current TMCC160 Ref. Switches DC/DC (3.3V) VM VM Motor V HALL U W HSx, LSx, BMx Power Bridge EEPROM SPI0 3.3V 3.3V Host PC or microcontroller VM R Optional Brake Circuit I_U, I_V or RS+, RS- 35 36 11 12 10 22 23 43 21 15/16/17 18/19/20 47/48/49 24/25/26441314 30/31/32/33 2/3/4/5 Figure 3: TMCC160 Hall-Sensor Block Diagram Depending on the used m otor, the customer can use a direct coil current measurement with external curre nt sensors for field oriented control; typically used for Permanent Magnet Synchronous Motors (PMSM) or single shunt measurement if block hall/ six step mode is configured in TMCC160 software (typical used for Brushless DC motors, BLDC). TMCC160 Block Diagram in Hall-Sensor Configuration Special Areas of Concern

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

3.4 Encoder Configuration

For applications which requires high positioning accuracy and a smooth run at low speed a motor with encoder is mandatory. TMCC160 supports incremental ABN encoders with a resolution of up to 16000 lines. Additional hall- sensors or encoder N -channel can be used for encoder initialization after power up. TMCC160 Block Diagram in Encoder Configuration Microcontroller UART CAN SPI1 AIN Gatedriver PWM DIAG Current TMCC160 Ref. Switches DC/DC (3.3V) VM VM Motor V Optional HALL U W HSx, LSx, BMx Power Bridge EEPROM SPI0 3.3V 3.3V Host PC or microcontroller VM R Optional Brake Circuit 35 36 11 12 10 22 23 43 21 15/16/17 18/19/20 47/48/49 24/ 25/ 441314 30/31/32/33 2/3/4/5 Encoder 27/ 28/ Figure 4: TMCC160 Encoder Block Diagram i If encoder configuration is used motor will be controlled by field oriented control, FOC.

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

4 External Components

4.1 Gate Driver Charge Pump (TMC6130)

For the external N-channel power MOSFET bridge, TMCC160 generates a 12V gate source voltage for high and low side MOSFETs (N-channel). The gate source voltage will also be maintained if the supply voltage falls below 12V. External component example is shown in schematic below. Buffer capacitor for charge pump linear regulator (C3) should not be smaller than 4.7µF. If the supply voltage does not fall below 12V charge pump circuitry can be left away without performance loss (connect VCP to VM, omit D1, D2, C2, VCP_SW not connected). C1 C2 D1 D2 VM VREG VM VCP_SW VCP TMCC160 VM 40V 1µF/25V 1µF/25V VCP_REG HSx BMx LSx GND Trickle Charge Pump Figure 5: Charge Pump Example Schematic i A component list example is provided on the next page.

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com Charge Pump Component List Example COMPONENT DESCRIPTION VENDOR ORDER CODE C1 2 X 4.7µF/35V ceramic capacitor Murata Electronics GRM219R6YA475MA73D TDK C2012X7R1V475K125AC C2 33nF/50V ceramic capacitor Multicomp MC0603B333J500CT AVX Corporation 06035C333JAT2A C3 4.7µF/25V ceramic capacitor Kemet C0805C475K3PACTU Murata Electronics GRM21BR61E475KA12L TDK CGA4J1X7R1E475K125AC D1, D2 60V/1A Vishay MSS1P6 (assembled on EVAL board) Table 1: Charge Pump Component List Example

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com 4.2 DC/DC Converter (3.3V) The 3.3V digital supply is generated with an internal step down switch regulator from VM. The step down converter works with a PWM f requency of 2.2MHz and supports a maximum output current of 500mA. A collection of external components like coils and diodes are listed below. Equivalent components can be used. The 3.3V can also be used to supply further external components like current-, hall sensors etc. if the consumption does not exceed 400mA. NOTE: → Place D1, L1, C1-C2 close to the TMCC160 pins SW, DA and VCC C1 C2 3.3V TMCC160 SW DA VCC DC/DC Figure 6: DC/DC Converter Example Schematic

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com DC/DC Component List Example COMPONENT DESCRIPTION VENDOR Series C1 100nF/16V ceramic capacitor C2 10µF/16V ceramic capacitor L1 6.8µH/700mA Murata Electronics LQH43C (assembled on EVAL board) Würth Elektronik WE-TPC, WE-PD2 Toko A916CY D1 40V/500mA low capacitance Vishay MSS1P6 (assembled on EVAL board) Diodes Inc. SBR1U40LP ON Semi MBRM140 Diodes Inc. DFLS140 Table 2:DC/DC Component List Example

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

4.3 CORTEX M4 Crystal

For system clock generation an external crystal is mandatory. As default, a crystal with 16MHz frequency and a frequency stability of ±5 0ppm should be used. Crystal frequency can be modified for customized firmware versions. Load capacitors C1, C2 depends on the used crystal. Values are typically in a range of 8-22pF. NOTE: → Place C1-C2, Q1 close to the TMCC160 pins TMCC160 C2C1 Microcontroller XTAL EXTAL Figure 7: Crystal Example Schematic Crystal Component List Example COMPONENT DESCRIPTION VENDOR Series C1 15pF/50V ceramic capacitor C2 15pF/50V ceramic capacitor Q1 16MHz crystal NDK NX3225SA Table 3: Crystal Component List Example

4.4 Supply Filter

To ensure proper operation VM and 3.3V supply voltage must be stable. TMCC160 already includes small buffer capacitors to stabilize the supply voltages . Nevertheless are additi onal capacitors mandatory. NOTE:

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com → Place C1 –C4 close to the TMCC160 pins VCC and VM. For a step down converter output current of 500mA a minimal total capacity of 10µF (C1 + C2) should be selected. i VM should be stabilized with minimum 2pcs. 4.7µF ceramic capacitors. Configuration for step down converter output TMCC160 VCC VM C3 C4 3.3V Output SW VM Microcontroller Gate DriverDC/DC 2X100nF 100nF 470nF Figure 8: Supply Filter Example Schematic

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com Supply Filter Component List Example COMPONENT DESCRIPTION VENDOR Series C1 100nF/16V ceramic capacitor C2 10µF/16V ceramic capacitor C3 4.7µF/35V ceramic capacitor Murata Electronics GRM219R6YA475MA73D TDK C2012X7R1V475K125AC C4 4.7µF/35V ceramic capacitor Murata Electronics GRM219R6YA475MA73D TDK C2012X7R1V475K125AC Table 4: Supply Filter Component List Example

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

4.5 Power MOSFET Bridge

TMCC160 provides a powerful gate driver for a three phase bridge using N-channel MOSFETs only. The system is capable to drive MOSFETs with up to 350nC gate charge. The gates of the MOSFETs will be charged with a current of ±1A. This helps to reduce dynamic losses and to building high efficient systems in a wide power range. A power MOSFET schematic including two phase direct coil current amplifier (e.g. AD8418) is shown below. The coil current measurement amplifiers can be powered by the 3.3V supply of the TMCC160. NOTE: → Integrate coil current amplifiers in motor coil connection U and V. C1 C2 C3 C4 C5 C6 HS1 HS2 HS3 LS1 LS2 LS3 VM BM3 BM2 BM1 R R W I_U BLDCV U I_V + Figure 9: Direct Coil Current Measurement Schematic i Direct coil current measurement is recommended for field oriented control (FOC) in hall- or encoder mode. It can also be used in block hall commutation (six step mode). NOTE: → Please note that the current amplifier has to be configured for bidirectional measurement. A sample schematic for direct coil current measurement with AD8418 is published in the TMCC160-EVAL board schematic. The input voltage range of the TMCC160 current sense inputs I_U, I_V is 0.. VCC. Both signals will be routed to the TMCC160 microcontroller and converted with a resolution of 12 bits. For a symmetric motor current measurement in positive and negative direct ion, the current amplifier must output VCC/2 at zero motor current to meet the TMCC160 offset configured. NOTE: 4.5.1 Direct Coil Current Measurement 4.5.2 Recommended Schematic for Direct Coil Measurement Current Sense Inputs

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com → Keep a safety margin for the current control of about 10% in order to avoid reaching the internal TMCC160 ADC limits. This margin shall be res pected for the current limit setting. Safety Margin Safety Margin 4095 2048 TMCC160 ADC Value I_U, I_V Input Voltage Vcc/2 (1.65V) Vcc (3.3V) Motor Current U, V +I target_peak 3890 205-I target_peak Figure 10: Direct Coil Current Signal Example Use formula below to calculate the sense resistors for direct coil current measurement. 𝑅𝑅𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆 = 1.48𝑉𝑉 𝐺𝐺 𝐼𝐼𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑆𝑆𝑡𝑡𝑝𝑝𝑝𝑝𝑝𝑝𝑝𝑝 1.48𝑉𝑉 𝐺𝐺 √2 ∗𝐼𝐼𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑆𝑆𝑡𝑡𝑅𝑅𝑅𝑅𝑅𝑅 (𝐺𝐺 = 𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶 𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐶𝐶𝐶𝐶 𝐺𝐺𝐺𝐺𝐴𝐴𝐶𝐶) G=20 (AD8418) Formulae 1: Direct Coil Current Sense Resistor Calculation TMCC160 Direct Coil Current Signal Example 4.5.3 Sense Resistor Selection

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com The power losses which are generated in the sense resistor can be calculated with formula below. 𝑃𝑃𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆 = 𝐼𝐼𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑆𝑆𝑡𝑡_𝑅𝑅𝑅𝑅𝑆𝑆 2 ∗𝑅𝑅𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆 = 𝐼𝐼𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑆𝑆𝑡𝑡_𝑝𝑝𝑆𝑆𝑡𝑡𝑝𝑝/√2 ∗𝑅𝑅𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆 Formulae 2: Direct Coil Current Sense Resistor Losses

4.5.5 Current Amplifier

COMPONENT DESCRIPTION VENDOR Series AD8418 ANALOG DEVICES AD8206 ANALOG DEVICES The single shunt measurement uses only one resistor in the bottom GND connection of the power MOSFET bridge . TMCC160 supports a high speed, high bandwidth, and low offset current sense amplifier with configurable input range for signal conditioning. NOTE: → Single shunt measurement is only possible for block hall (six step mode) commutation. 4.5.4 Calculating Power Losses 4.5.6 Single Shunt Measurement C1 C2 C3 C4 C5 C6 HS1 HS2 HS3 LS1 LS2 LS3 VM BM3 BM2 BM1 R W BLDCV U 100Ω 100Ω 100pF 100pF RS+ RS- Figure 11: Single Shunt Measurement Schematic

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com → A low pass with cut off frequency of approximately 16MHz should be placed on TMCC160 input RS+, RS- to filter high frequency. → Place RC low pass close to the TMCC160. Gain of the internal current sense amplifier can be configured by software. Following gain values are available: The accuracy of the amplifier is ±3%. The maximum input voltage between RS+ and RS- depends on the configured amplifier gain: 𝑈𝑈𝑅𝑅𝑡𝑡𝑀𝑀 = 1.48𝑉𝑉 𝐺𝐺𝐺𝐺𝐴𝐴𝐶𝐶 Formulae 3: Maximum Input Voltage Calculation With the given 𝑈𝑈𝑅𝑅𝑡𝑡𝑀𝑀 it is possible to calculate the sense resistor for a given maximum target current. Calculation formula for 𝑅𝑅𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆 is given below. The maximum current can be measured in both directions depending on the power MOSFET state. 𝑅𝑅𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆𝑆 = 1.48𝑉𝑉 𝐺𝐺𝐺𝐺𝐴𝐴𝐶𝐶 𝐼𝐼𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑆𝑆𝑡𝑡_𝑝𝑝𝑆𝑆𝑡𝑡𝑝𝑝 Formulae 4: Single Shunt Sense Resistor Calculation To protect each half bridge against cross-conduction during switching high- and low-side MOSFETs, TMCC160 includes a programmable dead time delay between high- and low-side MOSFET of the same phase. During the dead time high - and low-side MOSFETs are off. The dead time can be configured in software. Dead time: i To avoid high losses during switch event a proper dead time adaption is needed. A value of 1.1µS is a good start value for further tuning. TMCC160 provide s an integrate d 3 -phase gate driver for pure N -channel MOSSFET bridge. The gate driver is capable to drive the high - and low-side gate with up to 1A source, sink. This allows fast and high efficient switching of power MOSFETs with a gate charge up to 350nC. To drive the high- and low -side MOSFETs down to a supply voltage of 7V a charge pump is integrated. Gate - source voltage of high- and low-side gate driver output is 12V. The duration of the switching event depends on the total gate charge of the MOSFET and can be calculated with the formula below. 4.5.7 Sense Resistor Selection 4.5.8 Dead Time Logic 4.5.9 Power MOSFET Selection

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com 𝐶𝐶𝑆𝑆𝑆𝑆𝑆𝑆𝑝𝑝𝑆𝑆 = 𝑄𝑄𝑅𝑅𝑀𝑀𝑆𝑆𝑆𝑆𝑆𝑆𝑡𝑡 ±1𝐴𝐴 Formulae 5: MOSFET Switch Slope Calculation To avoid that negative voltage spikes (high frequency oscillation) reach the TMCC160 gate driver output pins during switch event s, high- and low-side gate series resistors (R) as well as optional clamp diodes (D) on low-side gate output are recommend. The negative voltage oscillation roots from the recovery effect of the MOSFET s body diodes during switching. A clamp circuit for BMx pins is integrated in the TMCC160. Gate Charge Resistors Table GATE CHARGE: MIN GATE SERIES RESISTOR [Ω]: LOW SIDE CLAMP DIODE: <50nC 10R optional 50..100nC 4.7R recommended >100nC 2.2R required Table 5: Gate Charge Resistor and Clamp Diode Recommendation NOTE: → Values in table above have to be validated in layout. Diagram: MOSFET Parameters During Switch Event Qg gate charge [nC] Vgs gate to source voltage [V] Rdson drain source resistance [R] Rdson QMiller Figure 12: MOSFET Parameters During Switch Event 4.5.10 Gate Driver Clamp Diodes Depending on the gate charge, the following gate series resistors are recommended:

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com → It is important to place the clamp diode close to LSx pin.

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com To ensure stable power supply voltage, please ensure that enough power supply filtering capacitors are available in the system to absorb kinetic energy during deceleration and load control . Additional a regulated power supply is recommended, especially if the system is operated close to the maximum supply voltage or a long power supply line is used. For power supply filtering capacitor value, the following rule of thumb can be used to calculate the system capacity (depending on the motor velocity 𝑰𝑰𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺 varies between 10% to 100% of the motor current): 𝐶𝐶𝐹𝐹𝑀𝑀𝑆𝑆𝑡𝑡𝑆𝑆𝑡𝑡 = 1000µ𝐹𝐹 ∗𝐼𝐼𝑆𝑆𝑆𝑆𝑝𝑝𝑝𝑝𝑆𝑆𝑆𝑆 i To reduce power losses in the capacitors and increase voltage stability use low ESR-capacitor type.

4.6 Interface

The TMCC160 system in a package supports RS232, RS485 , CAN and SPI interface as well as an analog input which can be used for control and parameterization. For easy intercommunication with a microcontroll er or a host PC TMCC160 system i n a package provides a 3.3V UART interface which can be directly connected to a microcontroller UART (3.3V TTL level) or connected to an external RS232 transceiver supporting a full RS232 signal interface. Diagram VREG VCP TMCC160 40V 1µF/25V VCP_REG HSx BMx LSx 2R2 R R VM 40V D U, V, W Figure 13: Gate Charge Resistor and Clamp Diode Example Schematic 4.5.11 Power Supply Filtering Capacitors 4.6.1 RS232

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com VCC C2- MAX3232CSE 3.3V RS232 TXD RS232 RXD TMCC160RXD TXD 100nF 100nF 100nF GND C2+ C1- C1+ 100nF Figure 14: RS232 Interface Example Schematic NOTE: → Circuit above shows an example of a RS232 interface configuration with external transceiver powered by the TMCC160 i nternal generated 3.3V supply voltage. Circuit above only shows an example , many other RS232 transceivers are available. For remote control and host communication the TMCC160 provides a two wire RS485 bus interface. A n external RS485 transceiver is required to integrate the TMCC160 into a RS485 bus structure. An example circuit is shown below, several other RS485 transceivers are available. NOTE: → TMCC160 is capable to supply a RS485 transceiver with the internal 3.3V power supply. → For a proper RS485 operation following items should be taken into account when setting up an RS485 network: 4.6.2 RS485

5 GND

B A VCC DE D R REN SN65HVD1781D 3.3V RS485+ RS485- TMCC160TXD RXD 100nF RS485_DIR Figure 15: RS485 Interface Example Schematic

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com The network topology should foll ow a bus structure as closely as possible. That is, the connection between each node and the bus itself should be as short as possible. Basically, it should be short compared to the length of the bus. Especially for longer busses and/or multiple nodes connected to the bus and/or high communication speeds, the bus should be pr operly terminated at both ends. Therefore, a 120 Ohm termination resistors at both ends of the bus have to be added. Avoid floating bus lines while neither the host/master nor one of the slaves along the bus line is transmitting data (all bus nodes switched to receive mode). Floating bus lines may lead to communication errors. In order to ensure valid signals on the bus it is recommended to use a resistor network connecting both bus lines in order to define logic levels appropriately. Two configuration options can be recommended. They are explained on the next page. Add resistor (Bias) network on one side of the bus, only (120R termination resistor still at both ends): Or add resistor (b ias) network at both ends of the bus (like Profibus™ termination): 4.6.3 RS485 Bus Structure c:> node node n - 1 node n Host Slave Slave Slave RS485 termination resistor (120 Ohm) termination resistor (120 Ohm) keep distance as short as possible Figure 16: RS485 Bus Interface Structure 4.6.4 RS485 Bus Termination 4.6.5 No Floating Bus Lines Configuration Option 1 node n - 1 node n Slave Slave termination resistor (120R) +5V GND pull-up (680R) pull-down (680R) RS485- / RS485B termination resistor (220R) RS485+ / RS485A Bus lines with resistor (Bias) network on one side, only Configuration Option 2

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com Certain RS485 interface converters available for PCs already include these additional resistors (e.g. USB-2-485 with bias network at one end of the bus). TMCC160 supports a full CAN 2.0B interface with up to 1Mbit/s. An external CAN transceiver is needed to integrate TMCC160 into a CAN bus network. It is possible to use TMCC160 internal generated 3.3V supply to power the IO voltage of a CAN transceiver like in picture below. NOTE: → The network topology should follow a bus structure as closely as possible. The connection between each node and the CAN bus itself should be as short as possible to avoid signal reflections. node n - 1 node n Slave Slave termination resistor (220R) +5V GND pull-up (390R) pull-down (390R) RS485- / RS485B RS485+ / RS485Atermination resistor (220R) +5V GND pull-up (390R) pull-down (390R) Figure 17: Bus lines with resistor (Bias) network at both ends 4.6.6 CAN 2.0B Interface

2 GND

S RXD TXD VIO TJA1051T/3 5V 3.3V CANL CANH TMCC160CAN_RXD CAN_TXD 100nF100nF Figure 18: CAN Interface Example Schematic 4.6.7 CAN Bus Structure c:> node node n - 1 node n Host Slave Slave Slave CAN termination resistor (120 Ohm) termination resistor (120 Ohm) keep distance as short as possible Figure 19: CAN Bus Structure

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com CAN bus must be properly terminated at both ends with a resistor of 120R between CANH, CANL signal. TMCC160 software supports CAN addresses up to 0x7FF (2047) but t he maximum number of nodes highly depends on the used transceiver and the bus structure itself. i Please see datasheet of used CAN transceiver for maximum number of CAN nodes. 4.6.8 CAN Bus Termination 4.6.9 Number of Nodes

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

4.6.10 Analog Input

The analog input signal of the TMCC160 can be used as a target value to e.g. control torque, velocity or other parameters. The analog input voltage is routed directly to the TMCC160 µC and will be converted with a resolution of 12 bit. AIN is designed for a voltage range between 0 and Vcc (3.3V). For higher voltages use a voltage divider plus optional protection diode as in example below. TMCC160AIN 3.3V 10k 22k 0..10V

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

4.7 EEPROM

To store and execute TMCL programs a EEPROM is needed. Interconnection between TMCC160 and EEPROM is done via SPI_ 0 interface. To ensure compatibility between TMCC160 default firmware and EEPROM , please use dedicated Atmel EEPROM listed below. It is possible to use TMCC160 internal generated 3.3V supply to power the EEPROM. EEPROM Connection Schematic 3.3V CS WP HOLD 7 SCK SI SO GND 3.3V 100nF

8 VCC

TMCC160SCLK_SPI0 32 MOSI_SPI0 30 MISO_SPI0 31 CSN_SPI0 33 IC1 Figure 20: EEPROM Connection Schematic COMPONENT DESCRIPTION VENDOR Series AT25128B-SSHL Atmel

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

4.8 Brake Chopper

A servo system feeds back energy to the power supply line during deceleration and load control. The energy can lead to a voltage ris e on the power supply system if it is not dissipated . The voltage overshoot of a system without brake chopper depends on the motor deceleration time, kinetic energy and the servo module buffer capacity. The brake chopper dissipates this energy from the system, and thus avoids system damage. TMCC160 provides a continuous motor voltage monitoring (20kHz) as well as a brake chopper output. The brake chopper output pin is controlled from a comparator implemented in TMCC160 software. Voltage threshold, hysteresis, enable/ disable is configurable via software. Motor voltage should be limited to 90% - 95% of the maximum possible operation voltage. For a full speed ramp stop, t he brake resistor should be able to dissipate the complete kinetic energy which is fed back during deceleration ramp (𝐶𝐶𝑑𝑑𝑆𝑆𝑑𝑑.). Kinetic energy: 𝐸𝐸𝐾𝐾𝑀𝑀𝑆𝑆 = 2 ∗𝐽𝐽∗𝜔𝜔𝑚𝑚𝑡𝑡𝑀𝑀. 2 [𝐽𝐽 = 𝐴𝐴𝑚𝑚𝐴𝐴𝐶𝐶𝐶𝐶𝐶𝐶 𝑚𝑚𝐴𝐴 𝐴𝐴𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐴𝐴𝐺𝐺𝐴𝐴, 𝜔𝜔 = 𝐺𝐺𝐶𝐶𝑎𝑎𝐶𝐶𝐴𝐴𝐺𝐺𝐶𝐶 𝑠𝑠𝐴𝐴𝐶𝐶𝐶𝐶𝑠𝑠] Deceleration time: 𝐶𝐶𝑑𝑑𝑆𝑆𝑑𝑑. Electrical energy: 𝐸𝐸𝐸𝐸𝑆𝑆𝑆𝑆𝑑𝑑. = 𝑃𝑃 ∗𝐶𝐶𝑑𝑑𝑆𝑆𝑑𝑑. = 𝑈𝑈𝑠𝑠𝑠𝑠𝑝𝑝𝑝𝑝𝑠𝑠𝑠𝑠2 𝑅𝑅 ∗𝐶𝐶𝑑𝑑𝑆𝑆𝑑𝑑. Brake resistor: 𝑅𝑅𝐵𝐵𝑡𝑡𝑡𝑡𝑝𝑝𝑆𝑆 = 𝑈𝑈𝑠𝑠𝑠𝑠𝑝𝑝𝑝𝑝𝑠𝑠𝑠𝑠2∗𝑡𝑡𝑑𝑑𝑝𝑝𝑑𝑑. 𝐸𝐸𝐾𝐾𝐾𝐾𝐾𝐾 Formulae 6: Brake Chopper Resistor Calculation Brake Chopper Output Brake Chopper Example Schematic R VM Gate Driver Brake (10) VM Software voltage threshold TMCC160 Software hysteresis Figure 21: Brake Chopper Example Schematic 4.8.1 Brake resistor selection

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com The figure below shows brake chopper in operation . The supply voltage threshold is configured at approximately 26V. The y ellow line represent s the supply voltage of the TMCC160. 4.8.2 Brake Chopper Example Start decceleration Activate brake chopper Figure 22: Supply Voltage Monitoring (Activated Brake Chopper)

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

4.9 Absolute Maximum Ratings

NOTE: → The maximum values must NOT be exceeded; under no circumstance. Absolute Maximum Ratings Parameter SYMBOL MIN TYP MAX U ni t Supply voltage, t<200ms VM -0.3 35 V Logic supply voltage VCC -0.3 3.8 V Table 6: TMCC160 Absolute Maximum Ratings

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

5 Operational Ratings

The operational ratings show the intended - or the characteristic - ranges and should be used as design values. NOTE: → The maximum values must NOT be exceeded; under no circumstance. Operational Ratings Parameter SYMBOL MIN TYP MAX Unit Supply voltage VM 7V 24 28 V Logic supply voltage VCC 3.0 3.3 3.6 V Logic Logic input voltage VI -0.3 VCC+0.3 V Logic input high VIH 0.7*VCC V Logic input low VIL 0.35*VCC Analog input voltage (pin: I_V, I_U, TEMP, AIN) VIA -0.3 VCC+0.3 V Gate Driver Gate driver supply (internal generated) VCP_REG 10 12 13 V Voltages on low side driver pins high (LSx) VOLSH 10 12 13 V Voltages on low side driver pins low (LSx) VOLSL -0.3 0 V Voltages on high side driver pins high (HSx) VOHSH VM+10 VM+12 VM+13 V Voltages on high side driver pins low (HSx) VOHSL VBM Pull-up ON resistance high-side gate driver RONHS 2.0 4.0 9.2 Ω Pull-up ON resistance low-side gate driver RONLS 2.4 4.0 7.0 Ω Pull-down ON resistance high -side gate driver (excluding 2R2 BM resistor) ROFFHS 2.0 5.0 9.2 Ω Pull-down ON resistance low-side gate driver ROFFLS 1.5 4.0 5.7 Ω Turn ON gate driver peak current IONP -1 -1.4 A Turn OFF gate driver peak current IOFFP 1 1.6 A Rise time (C=1nF, output 20% to 80%) tr 6 7 15 ns Fall time (C=1nF, output 20% to 80%) tf 4 7 15 ns Programmable dead time: DEAD_TIME [2:0]: [011] = 1.10µs default value. [000] [001] [010] [011] [100] [101] [110] [111] tdead -25% 0.00 0.51 0.80 1.10 1.67 2.30 3.40 6.90 +25% µs Gate Driver, continued Programmable drain-source voltage used for short to GND detection: VDSMON [2:0]: [111] = 2V default value. VVDS_MON V

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com Operational Ratings [000] [001] [010] [011] [100] [101] [110] [111] 0.40 0.60 0.85 1.05 1.25 1.50 1.70 dis. 0.50 0.75 1.00 1.25 1.50 1.75 2.00 0.60 0.90 1.15 1.45 1.75 2.00 2.30 Programmable drain-source voltage monitor blanking time: VDS_BLANK_TIME [1:0]: [10] = 3,4µs default value. [00] [01] [10] [11] TVDS_BL 0.60 1.28 2.55 5.10 0.80 1.70 3.40 6.80 1.00 2.13 4.25 8.50 µs 3.3V Switch Regulator Switch regulator output voltage U3.3VOUT 3.14 3.3 3.47 V 3.3V switch regulator output current I3.3VOUT 500 mA 3.3V switch regulator frequency f 1.8 2.25 2.8 MHz Temperature Ambient temperature (limited by CPU Flash memory upper die junction temperature limit of 95°C) TJ -40 85 °C Storage temperature TSTG -40 95 °C ESD-Protection (Human body model, HBM) VESD 2 (tbd) kV Table 7: Operational Ratings

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

6 Mechanical Dimensions

6.1 TMCC160 Package Footprint

The TMCC160 uses a special LGA package (similar to QFNs) with 51 leads.

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com Figure 23: TMCC160 LGA51 Package Drawing Table 8 Package Dimensions Attribute SYMBOL DIMENSION [mm] MIN TYP MAX Total Thickness A - - 1.4 Body Size D 17 E 12 Lead Width W 0.38 0.43 0.48 Lead Length L 0.38 0.43 0.48

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com Lead Pitch e 1 Lead Count n 51 Edge Ball Center to Center D1 16 E1 5 Body Center to Contact Ball SD - SE 0.5 Package Edge Tolerance aaa 0.1 Mold Flatness bbb 0.2 Coplanarity ddd 0.08 Package Code Type Package Temperature range Code & marking TMCC160-LC LGA-51 (RoHS) -40°C … +85°C TMCC160-LC Table 9: Package Code Marking Code Type Picture Date code Lot number TMCC160-LC WW: week YY: year LLLL: Lot number Table 10 Marking Code

6.1.1 Soldering Profile

TMCC160 system in a package is compatible with the JESD22 reflow soldering profile. Package Code Marking Code

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

7 SUPPLEMENTAL DIRECTIVES

Read the entire documentation before you make use of this product: Keep this manual and all other applicable and related documents complete, legible and accessible to the specified user at all times. Failure to observe the Supplemental Directives could result in damage to product and things; to property or persons; or economic loss. i TRINAMIC is not liable for damages incurred as a result of improper use or disregard of the instructions provided in this document. In case you encounter difficulties or need additional advice, please contact our support team via: www.trinamic.com. Thank you.

7.1 ESD Sensitive Device

This product is an ESD -sensitive CMOS device. It is sensitive to electrostatic discharge.

• Provide effective grounding to protect personnel and machines.
• Ensure work is performed in a non-static environment.
• Use personal ESD control footwear and ESD wrist straps, if necessary. Failure to do so can result in defects, damages and decreased reliability.

7.2 Disclaimer

TRINAMIC Motion Control GmbH & Co. KG does not authorize or warrant any of its products for use in life support systems, without the specific written consent of TRINAMIC Motion Control GmbH & Co. KG. Life support systems are equipment intended to support or sustain life, and whose failure to perform, when properly used in accordance with instructions provided, can be reasonably expected to result in personal injury or death. Information given in this data sheet is believed to be accura te and reliable. However no responsibility is assumed for the consequences of its use nor for any infringement of patents or other rights of third parties which may result from its use. Specifications are subject to change without notice. All trademarks used are property of their respective owners.

TMCC160 motionCookie™ (Rev. 1.00 / 2015-Nov-16) © 2015 TRINAMIC Motion Control GmbH & Co. KG, Hamburg, Germany Read entire DATASHEET USER MANUAL before use of product. Terms of delivery and rights to technical change reserved. Download newest version at: www.trinamic.com

8 Revision History

8.1 Document Revision

0.90 2015-APRIL- 09 JM Initial version. 0.91 2015-APRIL- 10 JM Add periphery sample schematics. 0.92 2015-MAY-26 JM 0.93 2015-JULY-15 JM Add brake chopper, revise gate driver parameters 0.94 2015-AUG-15 JM Add chapter soldering profile Add chapter software revision Add chapter ESD Sensitive Device Add chapter Disclaimer Add chapter Package Code 0.95 2015-SEPT-03 JM Add chapter Clamp Diode 0.96 2015-OCT-30 JP Formatting and Short Specification 1.00 2015-NOV-11 BD, JM Final Edits Table 11 Document revision

8.2 Hardware Revision

TMCC160-ES V1.0 2015-APRIL Initial Prototype Lot Table 12 Hardware revision

8.3 Software Revision

V2.07 2015-JUN-11 Initial TMCC160 Firmware V2.08 2015-SEPT-21 Changes Brake Chopper Algorithm Table 13 Hardware revision