TLE4208G

TLE4208 INFINEON | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 14

Technical content

Features

• Driver for up to 3 motors  Delivers up to 0.8 A continuous  Optimized for DC motor management applications  Very low current consumption in stand-by (Inhibit) mode  Low saturation voltage; typ.1.2 V total @ 25°C; 0.4 A  Output protected against short circuit  Error flag diagnosis  Overvoltage lockout and diagnosis  Undervoltage lockout  CMOS/TTL compatible inputs with hysteresis  No crossover current  Internal clamp diodes  Overtemperature protection with hysteresis and diagnosis  Enhanced power P-DSO-Package

Description

The TLE 4208 is a fully protected Quad-H alf-B ridge-D river designed specially for automotive and industrial motion control applications. The part is built using the Siemens bipolar high voltage power technology DOPL. In a cascade configuration up to three actuators (DC motors) can be connected between the four half-bridges. These four half-bridges are configured as 2 dual-half-bridges, which are supplied and controlled separately. Operation modes forward (cw), reverse (ccw), brake and high impedance are invoked from a standard interface. The standard enhanced power P-DSO-28 package meets the application requirements and saves PCB-board space and costs. Furthermore the built-in features like diagnosis, over- and undervoltage-lockout, short- circuit protection, over-temperature protection and the very low quiescent current in stand-by mode will open a wide range of automotive and industrial applications. Type Ordering Code Package TLE 4208 G Q67007-A9335 P-DSO-28-18

Figure 1 Pin Configuration (top view) 12 8 AEP02349 TLE 4208 G 21 GND GND GND OUT1 N.C. N.C. OUT3 GND IN1 GND IN3 N.C. IN4 EF OUT4 GND GND GND GND OUT2 IN2 GND V S34 S12V 12INH N.C. 34INH EF 12

Pin Definitions and Functions Pin No. Symbol Function 1, 6, 7, 8, 9, 14, 20, 21, 22, 23 GND Ground; negative reference potential for blocking capacitor 2E F

12 Error Flag output of half-bridges 1and 2;

open collector; low = error 3I N 1 Input channel of half-bridge 1; controls OUT1 4, 11, 15, 28 N.C. Not connected 5O U T 1 Power output of half-bridge 1; full short circuit protected; with integrated clamp diodes

10 OUT3 Power output of half-bridge 3;

full short-circuit protected; with integrated clamp diodes

12 IN3 Input channel of half-bridge 3;

13 INH 34 Inhibit input of half-bridges 3 and 4;

low = half-bridges 3 and 4 in stand-by

16 EF 34 Error Flag output of half-bridges 3 and 4;

open collector; low = error

17 IN4 Input channel of half-bridge 4;

18 VS34 Power supply voltage of half-bridges 3 and 4;

positive reference potential for blocking capacitor

19 OUT4 Power output of half-bridge 4;

full short circuit protected; with integrated clamp diodes

24 OUT2 Power-output of half-bridge 2;

full short circuit protected; with integrated clamp diodes

25 VS12 Power supply voltage of half-bridges 1 and 2;

positive reference potential for blocking capacitor

26 IN2 Input channel of half-bridge 2;

27 INH 12 Inhibit input of half-bridges 1and 2;

low = half-bridges 1 and 2 in stand-by

Fault-Detection 1,2 IN1 IN2 OUT1 OUT2 ZXZ X L0 L0 H0 L1 L1 H0 H1 H11 Inhibit 1,2 OUT4 Inhibit 3,4 Fault-Detection 3,4 X IN3 OUT3 X IN4 LH H H H L L Z L Z TLE 4208 G 9,14, 20,21, DRV1 DRV2 DRV3 DRV4 OUT4 OUT3 OUT2 OUT1 GND IN1 IN2 IN3 IN4 V S12 S34V INH AEB02350 22,23 EF 12 INH EF 34 1,6,7,8, 34INH INH 12

Note: Half-Bridge 1 and 2 connected to a full-bridge IN: 0 = Logic LOW OUT: Z = Outp ut in tristate condition 1 = Logic HIGH L = Output in sink condition X = don’t care H = Output in source condition Note: Half-Bridge 3 and 4 connected to a full-bridge Input Logic Functional Truth Table of Halfbridge 1 and 2 INH12 IN1 IN2 OUT1 OUT2 Mode

0 X X Z Z Stand-By

L L H H L H L H Brake LL CW CCW Brake HH Functional Truth Table of Half-Bridge 3 and 4 INH

34 IN3 IN4 OUT3 OUT4 Mode

L L H H L H L H Brake LL CW CCW Brake HH Diagnosis EF 12 EF 34 Error no error over temperature of half-bridge 1 and 2 or over voltage of half-bridge 1 and 2 over temperature of half-bridge 3 and 4 or over voltage of half-bridge 3 and 4 over temperature of all half-bridges or over voltage of all half-bridges

Electrical Characteristics

Note: Maximum ratings are absolute ratings; exceeding any one of these values may cause irreversible damage to the integrated circuit. Absolute Maximum Ratings Parameter Symbol Limit Values Unit Remarks min. max. Voltages Supply voltage VS12, VS34 – 0.3 45 V – Supply voltage VS12, VS34 – 1 – V t < 0.5 s; IS12, IS34 > – 2 A Logic input voltages (IN1; IN2; INH12; IN3; IN4; INH34) VI – 5 20 V 0V < VS12, VS34 < 45 V Logic output voltage (EF12; EF34) VEF12 , VEF34 – 0.3 20 V 0 V < VS12, VS34 < 45 V Currents Output current (cont.)IOUT1-4 – – A internally limited Output current (peak)IOUT1-4 – – A internally limited Output current (diode)IOUT1-4 –1 1 A – Output current (EF) IEF12-34 –2 5 mA – Temperatures Junction temperature Tj – 40 150 °C– Storage temperature Tstg – 50 150 °C– Thermal Resistances Junction pin Rthj-pin – 25 K/W measured to pin 7 Junction ambient RthjA –6 5 K / W –

Note: In the operating range the functions given in the circuit description are fulfilled. Operating Range Parameter Symbol Limit Values Unit Remarks min. max. Supply voltage VS12, VS34 VUV OFF 18 V After VS12, VS34 rising above VUV ON Supply voltage increasingVS12, VS34 – 0.3 VUV ON V Outputs in tristate Supply voltage decreasingVS12, VS34 – 0.3 VUV OFF V Outputs in tristate Logic input voltages (IN1; IN2; INH12; IN3; IN4; INH34) VI – 2 18 V – Junction temperature Tj – 40 150 °C–

8 V < VS12 = VS34 < 18 V; INH12 = INH34 = HIGH; IOUT1-4 = 0 A; – 40 °C < Tj < 150 °C;

unless otherwise specified Parameter Symbol Limit Values Unit Test Condition min. typ. max. Current Consumption INH12 = INH34 = LOW Quiescent current IS –– 1 0 0 µA IS = IS12 + IS34 Quiescent current IS –2 0 4 0 µA IS = IS12 + IS34; VS12 = VS34 =1 3 . 2V ; Tj = 25°C INH12 = HIGH and INH34 = LOW or INH12 = LOW and INH34 = HIGH Supply current IS12, IS34 –1 0 2 0 m A – Supply current IS12, IS34 –– 3 0 m A IOUT1/3 = 0.4 A IOUT2/4 = – 0.4 A Supply current IS12, IS34 –– 5 0 m A IOUT1/3 = 0.8 A IOUT2/4 = – 0.8 A Over- and Under Voltage Lockout UV Switch ON voltage VUV ON –6 . 5 7 . 5 V VS12, VS34 increasing UV Switch OFF voltage VUV OFF 56 – V VS12, VS34 decreasing UV ON/OFF hysteresis VUV HY –0 . 5 – V VUV ON – VUV OFF OV Switch OFF voltage VOV OFF –2 0 2 4 V VS12, VS34 increasing OV Switch ON voltage VOV ON 18 19.5 – V VS12, VS34 decreasing OV ON/OFF hysteresis VOV HY –0 . 5 – V VOV OFF – VOV ON

Outputs OUT1; OUT2; OUT 3; OUT 4 Saturation Voltages Source (upper) IOUT12 , IOUT34 = – 0.2 A VSAT U – 0.85 1.15 V Tj = 25 °C Source (upper) IOUT12 , IOUT34 = – 0.4 A VSAT U – 0.90 1.20 V Tj = 25 °C Sink (upper) IOUT12 , IOUT34 = – 0.8 A VSAT U – 1.10 1.50 V Tj = 25 °C Sink (lower) IOUT12 , IOUT34 = 0.2 A VSAT L – 0.15 0.23 V Tj = 25 °C Sink (lower) IOUT12 , IOUT34 = 0.4 A VSAT L – 0.25 0.40 V Tj = 25 °C Sink (lower) IOUT12 , IOUT34 = 0.8 A VSAT L – 0.45 0.75 V Tj = 25 °C Total Drop IOUT12 , IOUT34 = 0.2 A VSAT –1 1 . 4 V VSAT = VSAT U + VSAT L Total Drop IOUT12 , IOUT34 = 0.4 A VSAT –1 . 2 1 . 7 V VSAT = VSAT U + VSAT L Total Drop IOUT12 , IOUT34 = 0.8 A VSAT –1 . 6 2 . 5 V VSAT = VSAT U + VSAT L Clamp Diodes Forward voltage; upper VFU –1 1 . 5 V IF = 0.4 A Upper leakage current ILKU –– 5 m A IF = 0.4 A1) Forward voltage; lower VFL –0 . 9 1 . 4 V IF = 0.4 A Notes see page 11. Electrical Characteristics (cont’d) unless otherwise specified Parameter Symbol Limit Values Unit Test Condition min. typ. max.

Logic Inputs IN1; IN2; IN3; IN4 H-input voltage VIH –2 . 0 3 . 0 V – L-input voltage VIL 1.0 1.5 – V – Hysteresis of input voltageVIHY –0 . 5 – V – H-input current IIH –2 – 1 0 µA VI = 5 V L-input current IIL –1 0 0 –2 0 –5 µA VI = 0 V Logic Inputs INH12; INH34 H-input voltage VIH –2 . 7 3 . 5 V – L-input voltage VIL 1.0 2.0 – V – Hysteresis of input voltageVIHY –0 . 7 – V – H-input current IIH – 100 250 µA VINH = 5 V L-input current IIL –1 0 – 1 0 µA VINH = 0 V Error-Flags EF12; EF34 L-output voltage level VEFL –0 . 2 0 . 4 V IEF =2 m A Leakage current IEFLK – – 1 0 µA0 V < VEF < 7 V Electrical Characteristics (cont’d) unless otherwise specified Parameter Symbol Limit Values Unit Test Condition min. typ. max.

Note: The listed characteristics are ensured over the operating range of the integrated circuit. Typical characteristics specify mean values expected over the production spread. If not otherwise specified, typical characteristics apply at TA = 25°C and the given supply voltage. Thermal Shutdown Thermal shutdown junction temperature TjSD 150 175 200 °C– Thermal switch-on junction temperature TjSO 120 – 170 °C– Temperature hysteresis ∆T –3 0 – K – 1) Guaranteed by design. Electrical Characteristics (cont’d) unless otherwise specified Parameter Symbol Limit Values Unit Test Condition min. typ. max.

Figure 3 Application Circuit 1 (Device is Used as Dual-Full-Bridge-Driver) Fault-Detection 1,2 IN1 IN2 OUT1 OUT2 ZXZ X L0 L0 H0 L1 L1 H0 H1 H11 Inhibit 1,2 OUT4 Inhibit 3,4 Fault-Detection 3,4 X IN3 OUT3 X IN4 LH H H H L L Z L Z TLE 4208 G 20,21, DRV1 DRV2 DRV3 OUT4 OUT3 OUT2 OUT1 GND IN1 IN2 IN3 IN4 V S12 S34V EF34 INH34 EF12 INH12 AES02351 Cµ TLE 4278 G 3,4,5,10,11,12 769 Q Reset Out Watchdog Out Watchdog In 13 Watchdog Adjust Input V CCRWDIWDO 1N4001 C 22 F S µ100 nF C Ι 100 k R WA Ω Reset Adjust GNDD 100 nF C D 22 Fµ C Q Ω10 k QBR10 kΩ QAR VS = 12 V DRV4 INH12 INH34 22,23 1,6,7, 8,9,14

Saturation Voltage of Sink V SAT L over Temperature -50 0 A 15050 Ι S C AED02352 100 T j SV = 18 V = 13.2 VV S = 8 VV S µ AED02309 -50 mV SAT LV ˚C0 50 100 150 = 800 mAOUTΙ = 14 VSV 250 500 750 1000 = 400 mAOUTΙ = 200 mAOUTΙ Tj Saturation Voltage of Source V SAT U over Temperature Total Drop at outputs V SAT over Temperature AED02308 -50 mV SAT UV Ι OUT = 800 mA ˚C0 50 100 150 250 500 750 1000 1250 1500 = 400 mAOUTΙ = 200 mAOUTΙ = 14 VSV Tj AED02310 -50 mV SAT V ˚C0 50 100 150 = 14 VSV 500 1000 1500 2000 = 800 mAOUTΙ = 400 mAOUTΙ = 200 mAOUTΙ Tj

0.35 x 45˚ -0.2 Index Marking -0.418.1 141) 0.35 1.27 +0.152) 0.2 28x0.2 2.65 MAX. 0.1 2.45 -0.1 -0.2 7.6 1) 10.3±0.3 0.23 +0.09 MAX.8˚ +0.80.4 Does not include dambar protrusion of 0.05 max. per side Does not include plastic or metal protrusion of 0.15 max. per side P-DSO-28-18 (Plastic Dual Small Outline Package) Sorts of Packing Package outlines for tubes, trays etc. are contained in our Data Book “Package Information”. Dimensions in mmSMD = Surface Mounted Device