TFS282A1 VECTRON | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Tfs282a1.doc version 1.0 16.03.2000 VI TELEFILTER Filter Specification TFS 282 A1 1/4 VI TELEFILTER Vectron International, Inc. Potsdamer Straße 18
267 Lowell Road
Hudson, NH 03051 / USA Tel: (+49) 3328 4784-52 / Fax: (+49) 3328 4784-30 Tel: (603) 598-0070 Fax: (603) 598-0075 E-Mail: tft@telefilter.com E-Mail: vti@vtinh.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Measurement condition Ambient temperature: Input power level: dBm Terminating impedances for input: 420 Ω // - 1,3 pF for output: 420 Ω // - 1,3 pF External coil: 89 nH Construction and pin configuration see page 2 Characteristics Remark: Reference level for the relative attenuation arel of the TFS 282 A1 is the minimum of the pass band attenuation amin. The minimum of the pass band attenuation amin is defined as the insertion loss ae. The centre frequency fo is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed on 282 MHz without tolerance. The given values for the relative attenuation arel and for the group delay ripple have to be reached at the frequencies given below also if the centre frequency fo is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fo. D a t a typ. value tolerance/limit Insertion loss ae = amin 3,7 dB max 5 dB (Reference level) Nominal frequency fN 282,000 MHz Pass band ripple 282,0 MHz ± kHz max 1,5 dB Relative attenuation arel 282,0 MHz ± kHz 1,5 dB max 3 dB 282,0 MHz ± 400 kHz ... 282,0 MHz ± 600 kHz dB min 25 dB 282,0 MHz ± 600 kHz ... 282,0 MHz ± 800 MHz dB min 40 dB 282,0 MHz + 800 kHz ... 282,0 MHz + 1,4 MHz dB min 50 dB 282,0 MHz + 1,4 kHz ... 282,0 MHz + 3,0 MHz dB min 45 dB 282,0 MHz + 3,0 MHz ... 282,0 MHz + 30,0 MHz dB min 50 dB 282,0 MHz - 800 kHz ... 282,0 MHz - 30,0 MHz dB min 50 dB Group delay distortion GDD 282,0 MHz ± 100 kHz 0,7 µs max 2,0 µs Input power max 10 dBm DC voltage max 5 V Operating temperature range Storage temperature range Temperature coefficient of frequency TCf - 0,036 ppm/K² Frequency inversion temperature + 25 Generated: Checked / approved:
Tfs282a1.doc version 1.0 16.03.2000 VI TELEFILTER Filter Specification TFS 282 A1 2/4 VI TELEFILTER Vectron International, Inc. Potsdamer Straße 18 Hudson, NH 03051 / USA Tel: (+49) 3328 4784-52 / Fax: (+49) 3328 4784-30 Tel: (603) 598-0070 Fax: (603) 598-0075 E-Mail: tft@telefilter.com E-Mail: vti@vtinh.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Construction, pin configuration and 50 ΩΩΩΩ - matching network (All dimensions in mm) 282 A M28 Pin 1 Sym. Output Pin 5 Sym. Input Pin 2 Sym. Output Pin 6 Sym. Input Pin 3 External Coil Pin 7 Ground Pin 4 Package Ground Pin 8 Package ground
50 Ohm Test circuit 1
4, 7, 8 LB-IN LB-OUT SAW
50 Ohm Test circuit 2
4, 7, 8 LB-IN LB-OUT SAW
Tfs282a1.doc version 1.0 16.03.2000 VI TELEFILTER Filter Specification TFS 282 A1 3/4 VI TELEFILTER Vectron International, Inc. Potsdamer Straße 18 Hudson, NH 03051 / USA Tel: (+49) 3328 4784-52 / Fax: (+49) 3328 4784-30 Tel: (603) 598-0070 Fax: (603) 598-0075 E-Mail: tft@telefilter.com E-Mail: vti@vtinh.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Stability Characteristics After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 18 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration:
10 Hz to 500 Hz, 0,35 mm or 5g respectively, 1 octave per min, 10 cycles per plan, 3 plans;
- Damp heat: 25 °C to 55°C / 95% r.H. / 10 cycles (cycle) DIN IEC 68 - 2 – 30 Db 4. Resistance to solder heat (reflow): max. 2 times reflow process; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; Packing Tape & Reel: IEC 286 - 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 3000 Real of empty components at start: min 300 mm Real of empty components at start including leader: min 500 mm Trailer min 300 mm D o P o E F W P 1 EMBOSSED CARRIER TAPE COVER TAPE G P 2 B o A o 13,4 ± 0,1 D 1 Tape (all dimensions in mm) W : 16 ± 0,3 Po : 4 ± 0,1 Do : 1,5 + 0,5 E : 1,75 ± 0,1 F : 7,5 ± 0,1 G (min) : 0,75 P2 : 2 ± 0,05 P1 : 8 ± 0,1 D1(min) : 1,5 Ao : 5,4 ± 0,1 Bo : 5,4 ± 0,1 D1 : 1,5 + 0,5 A C N W 1 W 2 Reel (all dimensions in mm): A : 330 W1 : 16,4 +2 W2 (max) : 22,4 N (min) : >= 90 C : 13 ± 0,25 The minimum bending radius is 45 mm. The mounting surface of the filters faces the bottom side of the embossed carrier tape. The marking of the filters is able to read if the view is directed on the upper side of the carrier tape with the sprocket holes on the right side of the tape.
Tfs282a1.doc version 1.0 16.03.2000 VI TELEFILTER Filter Specification TFS 282 A1 4/4 VI TELEFILTER Vectron International, Inc. Potsdamer Straße 18 Hudson, NH 03051 / USA Tel: (+49) 3328 4784-52 / Fax: (+49) 3328 4784-30 Tel: (603) 598-0070 Fax: (603) 598-0075 E-Mail: tft@telefilter.com E-Mail: vti@vtinh.com VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Air reflow temperature conditions 1st and 2nd air reflow profile Name: pre-heating periods main-heating periods peak temperature Temperature: 150 °C - 170 °C over 200 °C 255 °C ± 5 °C Time: 60 sec. - 90 sec. 20 sec. - 25 sec. Chip-mount air reflow profile time / sec. temperature / °C 100 120 140 160 180 200 220 240 260 100 120 140 160 180 200 220 240 Table for temperature vs. time during the air reflow process Tolerance of temperatures: ± 5 °C time / sec. temperature / °C time / sec. temperature / °C 140 160 150 161 160 164 170 170 180 180 103 190 205 121 195 230 134 200 255 143 205 230 150 210 205 100 154 215 180 110 156 220 165 120 158 230 140 130 159 240 120