TFS210C

TFS210C VECTRON | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

VI TELEFILTER Vectron International, Inc. Potsdamer Straße 18 267 Lowell Road D 14 513 TELTOW / Germany Hudson, NH 03051 / USA Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 Tel: (603)598-0070Fax:(603) 598-0075 E-Mail: tft@telefilter.com E-Mail: vti@vtinh.com Measurement Condition Ambient temperature: 23 C Input power level: 0dBm Terminating impedances * Input: 295 || 1,15 pF Output: 295 || 1,15 pF Characteristics Remark: Reference level for the relative attenuation a rel of the TFS 210 C is the minimum of the pass band attenuation a min. The minimum of the pass band attenuation a min is defined as the insertion loss a e. The centre frequency f c is the arithmetic mean valueof the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss a e. The nominal frequency f N is fixed on 210,38 MHz without tolerance. The given values for the relative attenuation a rel and for the group delay ripple have to be reached at the frequencies given belowalso if the centre frequency fc is shifted due to the temperature coefficient of frequency TC f in the operating temperature range and due to a productiontolerance for the centre frequency f c. Data typ. Value Variation/ Limitation Insertion Loss ae = amin 6,6 dB max.8,0dB (Reference level) Nominal Frequency fN - 210,38MHz 3 dB - Band Width BW 54 kHz min.30 kHz Relative Attenuation arel fN ± 0kHz ... f N ± 13kHz - max. 1,5 dB fN ± 13kHz ... f N ± 15kHz - max. 3 dB fN ± 60 kHz 23 dB min.20dB fN ± 60kHz ... f N ±120kHz - min. 20 dB fN ± 120kHz ... f N ± 420kHz - min. 40 dB fN + 420kHz ... f N +1,25MHz - min.50 dB fN + 1,25MHz ... f N +2,05 MHz - min. 55 dB fN - 420kHz ... f N -2,05 MHz - min. 60 dB Group Delay Distortion GDD fN ± 0kHz ... f N ± 11 kHz - max. 9 µs Temperature Coefficient of Frequency TCf ** - 0,036 ppm/K2 - Frequency Inversion Temperature T0 + 25 °C - Operating Temperature Range - 10 °C ... + 60°C *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) f(Hz) = TCf(ppm/K²) x (T-T0)² x fTo(MHz) Generated: Checked / approved: VI TELEFILTER reserves the right to makechanges to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

VI TELEFILTER Vectron International, Inc. Potsdamer Straße 18 267 Lowell Road D 14 513 TELTOW / Germany Hudson, NH 03051 / USA Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 Tel: (603)598-0070Fax:(603) 598-0075 E-Mail: tft@telefilter.com E-Mail: vti@vtinh.com Construction and Pin Configuration (All dimensions in mm) S 210 C N32

1 Output

2 Ground

3 Ground

4 Ground

5 Ground

6 Ground

7 Input

8 Ground

9 Ground

10 Ground

... 50 test circuit 1 C1 C2 1 7 2,3,4,5,6,8, 9,10,11,12 50 test circuit 2 C1 C2 2,3,4,5,6,8, 9,10,11,12 VI TELEFILTER reserves the right to makechanges to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

VI TELEFILTER Vectron International, Inc. Potsdamer Straße 18 267 Lowell Road D 14 513 TELTOW / Germany Hudson, NH 03051 / USA Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 Tel: (603)598-0070Fax:(603) 598-0075 E-Mail: tft@telefilter.com E-Mail: vti@vtinh.com Stability Characteristics After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 18 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 1,5 mm or 20g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: -55 °C to 125°C / 30 min. each. / 10 cycles DIN IEC 68 part 2 – 14 Test N 4. Resistance to solder heat (reflow): max. 2 times reflow process; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; Packing Tape & Reel: IEC 286 - 3, with exception of value for N and minimum bending radius; tape type II,embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 3000 Reel of empty components at start: min 300 mm Reel of empty components at start including leader: min 500 mm Trailer min 300 mm Do Po E F W EMBOSSED CARRIER TAPE COVER TAPE G Bo Ao 13,4 ± 0,1 D 1 Tape (all dimensions in mm) W :16 ± 0,3 Po : 4 ± 0,1 Do : 1,5 + 0,5 E : 1,75 ± 0,1 F : 7,5 ± 0,1 G (min) : 0,6 P2 : 2 ± 0,05 P1 : 8 ± 0,1 D1(min) : 1,5 Ao : 5,5 ± 0,1 Bo : 7,5 ± 0,1 D1 : 1,5 + 0,5 A C N W 1 W 2 Reel (all dimensions in mm): A : 330 W1 : 16,4 +2 W2 (max) : 22,4 N (min) : 50 The minimum bending radius is 45 mm. The mounting surface of the filters faces the bottom side of the embossed carrier tape. The marking of the filters is able to read if the view is directed on the upper side of the carrier tape with the sprocket holes on the right side of the tape. VI TELEFILTER reserves the right to makechanges to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

VI TELEFILTER Vectron International, Inc. Potsdamer Straße 18 267 Lowell Road D 14 513 TELTOW / Germany Hudson, NH 03051 / USA Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 Tel: (603)598-0070Fax:(603) 598-0075 E-Mail: tft@telefilter.com E-Mail: vti@vtinh.com Air reflow Temperature Conditions 1st and 2nd air reflow profile Name: pre-heatingperiods main-heating periods peak temperature Temperature: 150 °C - 170 °C over 200 °C 255 °C ± 5 °C Time: 60 sec. - 90 sec. 20 sec. - 25 sec. Chip-mount air reflow profile time / sec. temperature / °C 100 120 140 160 180 200 220 240 260 0 20 40 60 80100120140160180200220240 Table for temperature vs. time during the air reflow process Tolerance of temperatures: ± 5 °C time / sec.temperature / °C time / sec.temperature / °C 0 23 140 160 10 34 150 161 20 46 160 164 30 60 170 170 40 80 180 180 50 103 190 205 60 121 195 230 70 134 200 255 80 143 205 230 90 150 210 205 100 154 215 180 110 156 220 165 120 158 230 140 130 159 240 120 VI TELEFILTER reserves the right to makechanges to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

VI TELEFILTER Vectron International, Inc. Potsdamer Straße 18 267 Lowell Road D 14 513 TELTOW / Germany Hudson, NH 03051 / USA Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 Tel: (603)598-0070Fax:(603) 598-0075 E-Mail: tft@telefilter.com E-Mail: vti@vtinh.com History VersionReason of Changes Name Date 1.6 Add “History” Herrler 09.08.2001 Add “50 test circuit” Correct “Tape and reel” information VI TELEFILTER reserves the right to makechanges to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.