TFS133C

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Filename: tfs 133c.doc Version 1.2 29.07.2009 Vectron International Filter specification TFS 133C 1/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of the ir use or application. No rights under any patent accompany the sale of any such product(s) or information. Measurement condition Ambient temperature: 25 ° C Input power level: 0 dBm Terminating impedance: * Input: 1090 Ω || -1,12 pF Output: 1090 Ω || -1,12 pF External Coil: 420 nH Characteristics Remark: The reference level for the relative attenuation a rel of TFS 133C is the minimum of the pass band attenu ation a min . This value is defined as the insertion loss a e. The centre frequency f c is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level r elative to the insertion loss a e. The temperature coefficient of frequency Tc f is valid for both the reference frequency f c and the frequency response of the filter in the op erating temperature range. The variation of the filter band width in the operating temperature range (OTR) is included in the production tolerance scheme. D a t a typ. value tolerance / limit Insertion loss ae 3,2 dB max. 6,0 dB (reference level) Centre frequency at ambient temperature fC 133,2 MHz ± 10,0 kHz Passband PB f C ± 50,0 kHz Pass band ripple p-p 0,9 dB max. 2,0 dB Relative attenuation arel fC … fC ± 50 kHz 1,3 dB max. 2,0 dB fC ± 50 kHz f C ± 70 kHz 2,3 dB max. 3,0 dB fC ± 180 kHz … fC ± 1,2 MHz 37 dB min. 35 dB fC - 128,2 MHz … fC - 1,2 MHz 60 dB min. 50 dB fC + 1,2 MHz … fC + 66,8 MHz * 61 dB min. 50 dB Absolute group delay within PB 7,5 µs max. 12 µs Group delay ripple within PB 2,8 µs max. 6 µs Input power level - max. 10 dBm Permissible DC voltage - max. 5 V Operating temperature range OTR - - 40 ° C ... + 90 ° C Storage temperature range - - 40 ° C ... + 90 ° C Frequency inversion temperature 10 ° C - Temperature coeffici ent of frequency TC f **** -0,036 ppm/K 2 - *) The terminating impedances depend on parasitics and q-values of matching elements and the board use d, and are to be understood as reference values only. Should there be additional questions do not h esitate to ask for an application note or contact our design team. ) The attenuation of coupling coil resonance can be down to 40 dB. The exact position will be define d. *) 2 narrow band distortions below 35 dB are acce ptable. ****) ∆ f(Hz) = TC f(ppm/K²) x (T-T0)² x f To (MHz) Generated: Checked / Approved:

Filename: tfs 133c.doc Version 1.2 29.07.2009 Vectron International Filter specification TFS 133C 2/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of the ir use or application. No rights under any patent accompany the sale of any such product(s) or information. Filter characteristic -27 -24 -21 -18 -15 -12 frequency in MHz magnitude in dB 1.2 2.4 3.6 4.8 7.2 8.4 9.6 10.8 frequency in MHz delay in µs -63 -56 -49 -42 -35 -28 -21 -14 frequency in MHz magnitude in dB insertion loss: -3.18 dB Construction and pin connection (All dimensions in mm) 2 Max. 5,2 Max. 7,2 Max. 0,80 2,54 ± 0,2 2,54 ± 0,2 Date code

50 Ohm Test circuit

• X31

1 Output

2 Output

3 Ground

4 External Coil

5 Ground

6 Ground

7 Input RF Return

8 Input

9 Ground

10 Ground

11 Ground

12 Ground

Date code: Year + week X 2009 A 2010 B 2011 ... SAW 3, 5, 6, 9, 10, 11, 12

Filename: tfs 133c.doc Version 1.2 29.07.2009 Vectron International Filter specification TFS 133C 3/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of the ir use or application. No rights under any patent accompany the sale of any such product(s) or information. Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respe ctively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: -55 ° C to 125° C / 30 min. each / 1 0 cycles DIN IEC 68 part 2 – 14 Test N 4. Resistance to solder heat (reflow): reflow possible: three ti mes max.; for temperature conditions refer to the attached " Air reflow temperature conditions" on page 4; 5. ESD MIL-STD-883E using coupling network of ISO 1 0605 and EN 6100-4-2 HBM:250V; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value f or N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 3000 reel of empty components at start: min. 300 mm reel of empty components at start including leader : min. 500 mm trailer: min. 300 mm G Do W Ct F E G P o Bo Ao P ull Off Direction PIN Marker T yp Date Code K o t A C N W 1 W 2 The minimum bending radius is 45 mm. Tape (all dimensions in mm) Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 7,50 ± 0,1 G(min) : 0,75 P2 : 2,00 ± 0,1 P1 : 8,00 ± 0,1 D1(min) : 1,50 Ao : 5,40 ± 0,1 Bo : 7,60 ± 0,1 Ct : 13,5 ± 0,1 Reel (all dimensions in mm) A : 330 W1 : 16,4 +2/-0 W2(max) : 22,4 N(min) : 50 C : 13,0 +0,5/-0,2

Filename: tfs 133c.doc Version 1.2 29.07.2009 Vectron International Filter specification TFS 133C 4/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of the ir use or application. No rights under any patent accompany the sale of any such product(s) or information. Air reflow temperature conditions Conditions Exposure Average ramp-up rate (30° C to 217° C) less than 3° C/ second > 100° C between 300 and 600 seconds > 150° C between 240 and 500 seconds > 217° C between 30 and 150 seconds Peak temperature max. 260° C Time within 5° C of actual peak temperature between 10 and 30 seconds Cool-down rate (Peak to 50° C) less than 6° C/second Time from 30° C to Peak temperature no greater than 300 seconds Temperature / ° C Time / s max. 260° C 217° C 10 ... 30 s 30 ... 150 s max. 300 s Chip-mount air reflow profile

Filename: tfs 133c.doc Version 1.2 29.07.2009 Vectron International Filter specification TFS 133C 5/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of the ir use or application. No rights under any patent accompany the sale of any such product(s) or information. History Version Reason of Changes Name Date 1.0 - Generation of development specification Strehl 12.01.2009 1.1 - Change pin connection Strehl 10.02.2009 - Add 50 Ω test circuit 1.2 - Generation of Filter specification Martens 29.07.2009 - Added typical values - Added filter impedance - Added group delay requirement