TFS115F

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Filename: tfs 115f.doc Version 1.3 16.8.2010 Vectron International Filter specification TFS 115F 1/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under an y patent accompany the sale of any such product(s) or information. Measurement condition Ambient temperature: 20 °C Input power level: 0 dBm Terminating impedance: * Input: 339 Ω || -24,5 pF Output: 295 Ω || -30,5 pF Characteristics Remark: The nominal frequency fN is fixed at 115,2 MHz. The insertion loss ae is defined as loss value determined at fN. Reference level for the relative attenuation arel of the TFS 115F is the insertion loss ae. All specified data are met within the operating temperature range. D a t a typ. value tolerance / limit Insertion loss ae 8 dB max. 10 dB (reference level) Nominal frequency fN 115,2 MHz Passband 1 PB 1 fN ± 1,92 MHz Passband 2 PB 2 fN ± 1,72 MHz Ripple in PB 1 p-p 0,3 dB max. 1 dB Relative attenuation arel fN ... fN ± 1,72 MHz 2 dB max. 2,5 dB fN ± 1,72 ... fN ± 1,92 MHz 2,5 dB max. 3 dB fN ± 4,2 MHz ... fN ± 7,5 MHz 40 dB min. 25 dB fN ± 7,5 MHz ... fN ± 12,5 MHz 48 dB min. 35 dB fN ± 12,5 MHz ... fN ± 25 MHz 60 dB min. 38 dB Absolute Group delay in PB 1 p-p 0,8 µs max. 0,85 µs Group delay ripple in PB 1 p-p 100 ns max. 150 ns Input power level - max. 10 dBm Temperature coefficient of frequency TCf * -22 ppm/K - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. ) Maximum value for 10 years operation. *) ∆fc(Hz) = TCf(ppm/K) x (T - To) x fTo (MHz). Generated: Checked / Approved:

Filename: tfs 115f.doc Version 1.3 16.8.2010 Vectron International Filter specification TFS 115F 2/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under an y patent accompany the sale of any such product(s) or information. Filter characteristic -90 -80 -70 -60 -50 -40 -30 -20 -10 frequency in MHz magnitude in dB frequency in MHz magnitude in dB 0.69 0.81 0.93 1.05 1.17 1.29 1.41 1.53 1.65 1.77 frequency in MHz delay in µs Construction and pin connection (All dimensions in mm)

1 Ground

2 Ground

3 Ground

4 Output RF Return

5 Output

6 Ground

7 Ground

8 Ground

9 Input RF Return

10 Input

• W04 Date code: Year + week W 2008 X 2009 A 2010 ... 50 Ω Test circuit SAW 9 4 5 10 1, 2, 3, 6, 7, 8

Filename: tfs 115f.doc Version 1.3 16.8.2010 Vectron International Filter specification TFS 115F 3/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under an y patent accompany the sale of any such product(s) or information. Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N 4. Resistance to solder heat (reflow): reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 3000 reel of empty components at start: min. 300 mm reel of empty components at start including leader: min. 500 mm trailer: min. 300 mm G Do W Ct F E G Po Bo Ao Pull Off Direction PIN MarkerTyp Date Code Ko t Tape (all dimensions in mm) W : 16,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 7,50 ± 0,1 G(min) : 0,60 P2 : 2,00 ± 0,1 P1 : 8,00 ± 0,1 D1(min) : 1,50 Ao : 5,50 ± 0,1 Bo : 7,50 ± 0,1 Ct : 13,5 ± 0,1 A C N W 1 W 2 Reel (all dimensions in mm) A : 330 W1 : 16,4 +2/-0 W2(max) : 22,4 N(min) : 50 C : 13,0 +0,5/-0,2 The minimum bending radius is 45 mm.

Filename: tfs 115f.doc Version 1.3 16.8.2010 Vectron International Filter specification TFS 115F 4/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under an y patent accompany the sale of any such product(s) or information. Air reflow temperature conditions Conditions Exposure Average ramp-up rate (30°C to 217°C) less than 3°C/second > 100°C between 300 and 600 seconds > 150°C between 240 and 500 seconds > 217°C between 30 and 150 seconds Peak temperature max. 260°C Time within 5°C of actual peak temperature between 10 and 30 seconds Cool-down rate (Peak to 50°C) less than 6°C/second Time from 30°C to Peak temperature no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C Time / s max. 300 s 10 ... 30 s 30 ... 150 s

Filename: tfs 115f.doc Version 1.3 16.8.2010 Vectron International Filter specification TFS 115F 5/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under an y patent accompany the sale of any such product(s) or information. History Version Reason of Changes Name Date 1.0 Generate development specification Strehl 14.06.2006 1.1 2 passbands introduced Strehl 28.07.2006 1.2 Generate filter specification Chilla 24.01.2008 terminating impedances added typical values added filter characteristics added test circuit added 1.3 pinning typo corrected Chilla 16.8.2010