TFS110AB

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Filename: TFS110AB.doc Version 1.3 22.03.2011 Vectron International Filter specification TFS 110AB 1/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Vectron International GmbH & Co. KG reserves the right to ma ke changes to the product(s) and/or information contained herein without Measurement condition Ambient temperature: 23 °C Input power level: 0 dBm Terminating impedance: * Input: 1083 Ω || -11,4 pF Output: 1144 Ω || -10,6 pF Characteristics Remark: The nominal frequency fN is fixed at 110,6 MHz. The insertion loss ae is defined as loss value determined at fN. Reference level for the relative attenuation arel of the TFS 110AB is the insertion loss a e. The centre frequency fc is the arithmetic mean v alue of the upper and low er frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. All specified data are met within the operating temperature range. D a t a typ. value tolerance / limit Insertion loss ae 7,5 dB max. 10 dB (reference level) Nominal frequency fN - 110,6 MHz Centre frequency fC 110,6 MHz - Passband PB - fN ± 0,5 MHz Amplitude ripple within PB 2,5 dB max. 3 dB Relative attenuation arel fN … fN ± 0,5 MHz 2,5 dB max. 3 dB fN ± 1 MHz … fN ± 1,05 MHz 43 dB min. 35 dB fN ± 1,05 MHz … fN ± 10 MHz 44 dB min. 40 dB Group delay ripple within fN ± 0,4 MHz p-p 400 ns max. 700 ns Group delay ripple within fN ± 0,5 MHz p-p 800 ns max. 1000 ns Operating temperature range OTR - - 20 °C ... + 70 °C Storage temperature range - - 40 °C ... + 85 °C Frequency inversion temperature - - Temperature coefficient of frequency TCf ** -0,04 ppm/K *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) ∆f(Hz) = TCf(ppm/K2) x (T-T0)2 x fcat(MHz). Generated: Checked / Approved: notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

Filename: TFS110AB.doc Version 1.3 22.03.2011 Vectron International Filter specification TFS 110AB 2/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Filter characteristic -60 -50 -40 -30 -20 -10 frequency in MHz magnitude in dB frequency in MHz magnitude in dB 0.5 1.5 2.5 3.5 4.5 frequency in MHz delay in µs Construction and pin connection (All dimensions in mm) Date code 11,5 +/-0,2 5,1 +/-0,2 1,8 +/-0,2 5,08 +/-0,2 0,8 +/-0,2 1,0 +/-0,2 2,54 +/-0,2 1 23 678 Date code: Year + week B 2011 C 2012 D 2013 ...

1 Ground

2 Ground

3 Ground

4 Output

5 Output RF Return

6 Ground

7 Ground

8 Ground

9 Input

10 Input RF Return

• B13

50 Ohm Test circuit

VECTRON reserves the right to make changes to the product(s) and/or information contained herein w ithout notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

Filename: TFS110AB.doc Version 1.3 22.03.2011 Vectron International Filter specification TFS 110AB 3/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N 4. Resistance to solder heat (reflow): reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; 5. ESD ANSI/ESD S20.20-1999, class 1A for HBM This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 3000 reel of empty components at start: min. 300 mm reel of empty components at start including leader: min. 500 mm trailer: min. 300 mm G Do W Ct F E G Po Bo Ao Pull Off Direction PIN MarkerTyp Date Code Ko t Tape (all dimensions in mm) W : 24± 0,3 Po : 4 ± 0,1 Do : 1,5 + 0,1 E : 1,75 ± 0,1 F : 11,5 ± 0,1 G (min) : 0,6 P2 : 2 ± 0,1 P1 : 8 ± 0,1 D1(min) : 1,5 Ao : 5,5 ± 0,1 Bo : 11,9 ± 0,1 CT : 21,5 ± 0,1 Reel (all dimensions in mm): A : 330 W1 : 24,4 +2 W2 (max) : 30,4 N (min) : 60 C : 13 +0,5/-0,2 A C N W 1 The minimum bending radius is 45 mm. VECTRON reserves the right to make changes to the product(s) and/or information contained herein w ithout notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

Filename: TFS110AB.doc Version 1.3 22.03.2011 Vectron International Filter specification TFS 110AB 4/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com Air reflow temperature conditions Conditions Exposure Average ramp-up rate (30°C to 217°C) less than 3°C/second > 100°C between 300 and 600 seconds > 150°C between 240 and 500 seconds > 217°C between 30 and 150 seconds Peak temperature max. 260°C Time within 5°C of actual peak temperature between 10 and 30 seconds Cool-down rate (Peak to 50°C) less than 6°C/second Time from 30°C to Peak temperature no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C Time / s max. 300 s 10 ... 30 s 30 ... 150 s VECTRON reserves the right to make changes to the product(s) and/or information contained herein w ithout notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.

Filename: TFS110AB.doc Version 1.3 22.03.2011 Vectron International Filter specification TFS 110AB 5/5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: tft@vectron.com History Version Reason of Changes Name Date 1.0 - development specification Pfeiffer 04.02.2010 1.2 - Adjust rejection levels as agreed with the customer A. Jaffer 13.07.2010 1.3 - Change from development spec to filter spec Molke 22.03.2011 - Typical values added - Filter characteristic added VECTRON reserves the right to make changes to the product(s) and/or information contained herein w ithout notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.