TA32

TA32 TIMOTION | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 6

Technical content

TA32 is a head tilt motor for recliner applications. It can help with adjusting the top head position which will make the end users with more pleasant using experience. General Features Voltage of motor 24V DC, 24V DC (PTC) Maximum load in push 500N Maximum speed at full load 8.8mm/s (with 300N in a push condition) Stroke 050 / 044 / 040 / 034 / 031 / 025 / 015mm Minimum installation dimension 143mm Color Black or grey Certificate UL962 Product Segments

• Comfort Motion TA32 series

1 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 2 The current & speed in table are tested when the actuator is extending under push load. Load and Speed CODE Load (N) Typical Current (A) Typical Speed (mm/s) Push Pull No Load 32V DC With Load 24V DC No Load 32V DC With Load 24V DC Motor Speed (5000RPM, duty cycle 10%) A 500 300 0.1 0.8 11.0 4.8 B 300 300 0.1 0.6 16.0 8.8 TA32 series Standard Dimensions (mm) Drawing ø21 44.5 49.7 91 .5 Retracted Length 102.6 14.514.4 49.7

Motor Speed (5000RPM, Duty cycle 10%) Performance Data (24V DC Motor) TA32 series 6.0 16.0 8.0 10.0 12.0 14.0 1000 200 300 400 500 A B 4.0 Speed (mm/s) Speed vs. Load Load (N) 0.1 0.0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0 200100 400300 500 A B Current (A) Current vs. Load Load (N)

Version: 20170718-B Load and Speed Voltage IP Rating Color Direction of Rear Attachment (Counterclockwise) See page 5 2 = 24V 5 = 24V, PTC 1 = Without 1 = Black 2 = Grey (Pantone 428C) 1 = 0° 2 = 90° Stroke (mm) Retracted Length (mm) See page 2 143 Stroke limitation 050 / 044 / 040 / 034 / 031 / 025 / 015 Rear Attachment (mm) See page 5 Front Attachment (mm) See page 5 1 = Plastic, U clevis, width 6.6, depth 18.6, hole 10.0 1 = Plastic, U clevis, width 6.6, depth 18.6, hole 10.0 Cable Length (mm) Output Signals Connector See page 6 1 = Straight, 500 2 = Straight, 750 3 = Straight, 1000 4 = Straight, 1250 5 = Straight, 1500 6 = Straight, 2000 7 = Curly, 200 8 = Curly, 400 B~H = For direct cut system See page 6 0 = Without 4 = One Hall sensor 5 = Two Hall sensors 1 = DIN 6P , 90° plug 2 = Tinned leads 3 = Small 01P , plug B = Y cable (direct cut, no water proof, no anti - pull) Functions for Limit Switches See page 6 1 = Two switches at full retracted / extended positions to cut current 3 = Two switches at full retracted / extended positions to send signal Special Functions for Spindle Sub- Assembly 0 = Without (Standard)

Rear Attachment (mm) 1 = Plastic, U clevis, width 6.6, depth 18.6, hole 10.0 1 = Plastic, U clevis, width 6.6, depth 18.6, hole 10.0 Front Attachment (mm) 18.6 ø10 ø21 6.6 21 .8 18.6 ø10 ø21 6.6 1 = 0° 2 = 90° Direction of Rear Attachment (Counterclockwise)

Functions for Limit Switches Wire Definitions CODE Pin 1 (Green) 2 (Red) 3 (White) 4 (Black) 5 (Yellow) 6 (Blue) 1 extend (VDC+) N/A N/A N/A retract (VDC+) N/A 3 extend (VDC+) common upper limit switch N/A retract (VDC+) lower limit switch 1 = DIN 6P , 90° plug 2 = Tinned leads 3 = Small 01P , plug Connector B = Y cable (direct cut, no water proof, no anti - pull) Cable length for direct cut system (mm) CODE L1 L2 L3 B 100 100 100 C 100 1000 400 D 100 2700 500 E 1000 100 100 F 100 600 1000 G 1500 1000 1000 H 100 100 1200 L2 L1 Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice.