SR7820 MPD | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Key Features:  Effi ciency to 92%  2A Output Current  Compact SIP Case  LM78xx Replacement  Wide Input Range  Short Circuit Protected  Thermal Shutdown  Low Noise  Low Low Cost SR7820 Low Cost, 2A Output Non-isolated POL Switching Regulators Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy ±2.0 ±3.0 % Line Regulation Vin = Min to Max ±0.5 ±0.75 % Load Regulation Iout = 10% to 100% ±0.5 ±1.0 % Ripple & Noise (20 MHz) 25 45 mV P - P Thermal Shutdown See Note 2 150 °C Quiescent Current See Note 3 5 10 mA Temperature Coeffi cient 0.03 %/°C Maximum Capacitive Load 1,000 µF Output Current Limit 5,000 mA Short Circuit Input Power 0.5 1.8 W Output Short Circuit Continuous (Autorecovery) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage Not Isolated Switching Frequency 280 330 450 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -40 +25 +85 °C Operating Temperature Range Case +100 °C Storage Temperature Range -55 +125 °C Lead Temperature 1.5 mm From Case For 10 Sec 300 °C Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Black Plastic (UL-94V0) Weight 0.13 Oz (3.7g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F , 25°C, Gnd Benign 2.0 MHours Series MicroPower Direct

292 Page Street

Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Typical Application Circuit Notes: 1. C1 is a low ESR ceramic capacitor used to minimize noise at the regulator. A tantalum or low ESR electrolytic capacitor may also be used. 2. C1 & C2 are required and should be mounted as close to the regulator pins as possible. Component Values Model Number Capacitors C1, C3 (µF/V) C2, C4 (µF/V) SR7820-015W 10 /25 22 / 6.3 SR7820-018W 10 /25 22 / 6.3 SR7820-02W 10 /25 22 / 6.3 SR7820-03W 10 /25 22 / 6.3 SR7820-05W 10 /25 22 / 16 SR7820-06W 10 /25 22 / 16 Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. www.micropowerdirect.com

Notes: 1. Load regulation is specifi ed for an output load change of 10% to 100%. 2. Measured at an internal IC junction. 3. Quiescent current is specifi ed at 0% load for Vin = min to max. 4. This regulator is not designed to be used in parallel with another unit to increase output power. 5. The input should not exceed the range given in the model selection chart. Exceeding this limit could damage the unit. For right-angle pin option, add suffi x “L” to model number (i.e. SR7820-05WL) Model Selection Guide Mechanical Dimensions Pin 1 2 3 Function +Vin Gnd +Vout Pin Connection Model Number Input Voltage Range (VDC) Output Effi ciency (%, Typ) Voltage (VDC) Current (mA, Max) Min Vin Max Vin SR7820-015W(L) 4.75 - 18.0 1.5 2,000.0 79 76 SR7820-018W(L) 4.75 - 18.0 1.8 2,000.0 81 79 SR7820-02W(L) 4.75 - 18.0 2.5 2,000.0 85 83 SR7820-03W(L) 4.75 - 18.0 3.3 2,000.0 87 86 SR7820-05W(L) 7.00 - 18.0 5.0 2,000.0 91 88 SR7820-06W(L) 8.50 - 18.0 6.5 2,000.0 92 91 Derating Curve Characteristic Curves (Effi ciency & Ripple) Effi ciency vs Input Voltage (Full Load) Ripple vs Input Voltage (Full Load) Ripple vs Load (Vin = Nom) Effi ciency vs Load (Vin = Nom) www.micropowerdirect.com MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072  TEL: (781) 344-8226  FAX: (781) 344-8481  E-Mail: sales@micropowerdirect.com Notes:

  • All dimensions are typical in inches (mm)
  • Tolerance x.xx = ±0.01 (±0.25)
  • Pin 1 is marked by a “dot” or indentation on the side of the unit