G100E MPD | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

292 Page Street

Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Low Cost, 1W MiniDIP Single & Dual Output DC/DC Con vert ers Key Features:

  • 1W Output Power
  • Compact “MiniDIP” Case
  • UL Approved (File E245422)
  • Single & Dual Outputs
  • 1,000 VDC Isolation
  • >3.5 MHour MTBF
  • 24 Standard Models
  • LOWEST COST!! L C t 1W Mi iDIP G100ESeries Input Parameter Conditions Min. Typ. Max. Units Input Voltage Range 5 VDC Input 4.5 5.0 5.5 VDC12 VDC Input 10.8 12.0 13.2 24 VDC Input 21.6 24.0 26.4 Input Filter Internal Capacitor Reverse Polarity Input Current 0.3 A Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy ±1.0 ±3.0 % Output Voltage Balance Dual Output , Balanced Loads ±0.1 ±1.0 % Line Regulation For Vin Change of 1% ±1.2 % Load Regulation (Note 1) See Model Selection Guide Ripple & Noise (20 MHz) (Note 2) 50 75 mV P - P Output Power Protection 120 % Temperature Coeffi cient ±0.02 ±0.03 %/ºC Output Short Circuit Momentary (1.0 Sec.) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 1,000 VDC Isolation Resistance 500 VDC 1,000 MΩ Isolation Capacitance 100 kHz, 1V 60 pF Switching Frequency 100 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -40 +25 +85 ºC Storage Temperature Range -55 +125 ºC Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Black Plastic (UL94-V0) Weight 0.07 Oz (2.1g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 25ºC, Gnd Benign 3.5 MHours Safety Standards UL 1950, EN 60950, IEC 60950 Safety Approvals UL, cUL; File No. E245422 Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 5 VDC Input -0.7 9.0 VDC12 VDC Input -0.7 18.0 24 VDC Input -0.7 30.0 Lead Temperature 1.5 mm From Case For 10 Sec 300 ºC Internal Power Dissipation All Models 450 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. RoHS Compliant Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice.

(%, Max) Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load Derating Curve Model Selection Guide Mechanical Dimensions Notes:

  • All dimensions are typical in inches (mm)
  • Tolerance x.xx = ±0.01 (±0.25)
  • Pin 1 is marked by a “dot” or indentation on the top of the unit Notes: 1. Output load regulation is specifi ed for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capaci- tor be placed from the +Vout pin to the -Vout pin for single output units and from each out- put to common for dual output units. An input capacitor will enhance stability over tempera- ture and input line variations. Recommended capacitor values are given in the table above. For applications requiring very low output noise levels, a simple LC fi lter should be effective. 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and fl oat the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Vin Input Capacitor Vout Output Capacitor Single Dual 5 VDC 4.7 μF 5 VDC 10.0 μF 4.7 μF 12 VDC 2.2 μF 9 VDC 4.7 μF 2.2 μF 24 VDC 1.0 μF 12 VDC 2.2 μF 1.0 μF 15 VDC 1.0 μF 0.47 μF Other input/output combinations are available (i.e. 3.3 VDC). Contact the factory for details at: sales@micropowerdirect.com Pin Single Dual Pin Single Dual 1 -Vin -Vin 9 +Vout +Vout

7 NC NC 11 -Vout -Vout

8 No Pin Common 14 +Vin +Vin

NC = No Connection Pin Connections MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com