SR11 LUMEL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 4

Technical content

Export department: Tel.: +48 68 45 75 139 / /276/ 386 Fax: +48 68 32 54 091 e-mail: export@lumel.com.pl lumel s.a. ul. sulechowska 1 65-022 Zielona Góra Poland WWW.LUMEL.COM.PL SR11 system for injection moulds with heated channels GALVANIC ISOLATION: OUTPUTS: RS 485Supply INPUTS: Digital interface Type of interface Properti es Remarks RS-485 Modbus ASCII (8N1, 7E1, 7O1) and RTU (8N1, 8N2, 8E1, 8O1) baud rate up to 19 200 bit/s Input Input type Range Error FE-CuNi (J) 0 .. 537 °C  0.2% of range +/- 1 digit logic 24 V d.c. PID Aalgorithm Password protection RS 485 FEATURES: Fuzzy Logic Auto- tuning Outputs Output type Properti es Remarks SSR relay 15 A, 230 V a.c./ heati ng zone up to 8 control outputs voltageless relay 1 A maximum 50 V a.c./d.c., NO contact signaling of control deviati on overfl ow Soft Start

  • Complete set for temperature control in injecti on moulds with heated channels.
  • System equiped with 1 or up to 8 controllers in one housing (depending on the version).
  • Built-in 15 A SSR output for each control zone (output resoluti on: 0.1 A).
  • PID control wit autotuning and Fuzzy logic algorithm ensuring a high temperature control accuracy and opti mal energy consumpti on.
  • “Soft start” functi on enables the mould preheati ng.
  • Monitoring of the leakage current of heater.
  • Signalling of breaks, short-circuits and inverse polari- zati on of the sensor.
  • Measurement of the heater leakage current and detecti on of the maximal current exceeding.
  • Measurement of the load current, detecti on and damage signalling.
  • Emergency work mode aft er the thermocouple damage with a mean power delivered before the damage with a mean power delivered before the damage or with the output turned off .
  • RS-485 interface with MODBUS protocol (ASCII and RTU modes) for connecti on with PC, recorders or other Modbus devices.
  • Decreased temperature mode (remote acti vati on with logic input or local acti vati on using the butt ons).
  • Relay output to signal the alarm states. Example of application SR11 set SR11-3 SR11-6 SR11-8

Export department: Tel.: +48 68 45 75 139 / /276/ 386 Fax: +48 68 32 54 091 e-mail: export@lumel.com.pl LUMEL S.A. ul. Sulechowska 1 65-022 Zielona Góra POLAND WWW.LUMEL.COM.PL Safety and compatibility requirements Electromagnetic compatibility noise immunity acc. to EN 61000-6-2 noise emissions acc. to EN 61000-6-4 Pollution level 2 Installation category III Maximal operating phase-to-earth voltage for supply circuit and output circuit:

300 V for other circuits: 50 V

Altitude a.s.l. 2000 m E l e m e n t s o f t h e sy st e m Fig.1. Completion of the SR11 system with ZP11 connections sets SR11 system for injection moulds with heated channels Rated operating conditions Supply voltage 1 zone system: 230 V a.c. +/- 10% 2 .. 8 zone system: frequency 50/60 Hz +/- 10% Relative humidity < 85% inadmissible condensation Operating position vertical External magnetic field < 400 A/m External features Overall dimensions of the housing: SR11-1XXXX R11-3XXXX SR11-6XXXX SR11-8XXXX Heihgt [mm] 200 197 Width [mm] 77.5 215 365 465 Depth [mm] 355 Weight of the SR11 system[kg], ca. 2 7 10 12 Readout field 14 mm LED, 2 x 3 digits Protection grade (acc. to EN 60529) IP30

Export department: Tel.: +48 68 45 75 139 / /276/ 386 Fax: +48 68 32 54 091 e-mail: export@lumel.com.pl lumel s.a. ul. sulechowska 1 65-022 Zielona Góra Poland WWW.LUMEL.COM.PL Acc es so r i es 1 - ZP11-1 connection set 2 - ZP11-2 connection set 3 - ZP11-3 connection set 4 - ZP11-4 connection set SR11 system for injection moulds with heated channels V i e o f t h e sy st e m p l at e Fig.3. Lay-out of SR11-6XX1X system connectors. Indicators of alarm states Indicators informing about displayed parameters Display of measured value Display of set point value, output power or current intensity Indicators of controller operati ng mode Push-butt ons to set parameters and the operati ng mode selecti on Supply swith Holder to pull the module out Fig.2 Frontal plate Signaling connector Main power-switch Supply cableG2 socket G1 socket   For more information about LUMEL’s products please visit our website: www.lumel.com.pl

Export department: Tel.: +48 68 45 75 139 / /276/ 386 Fax: +48 68 32 54 091 e-mail: export@lumel.com.pl LUMEL S.A. ul. Sulechowska 1 65-022 Zielona Góra POLAND WWW.LUMEL.COM.PL Ordering System SR11 - X X X X X Housing dimensions: housing width 77.5 mm number of controllers: 1 1 housing width 215 mm number of controllers: 2, 3 3 housing width 365 mm number of controllers: 4, 5, 6 6 housing width 465 mm number of controllers: 7, 8 8 Number of controllers: 1 controller 1 2 controllers 2 3 controllers 3 4 controllers 4 5 controllers 5 6 controllers 6 7 controllers 7 8 controllers 8 RS-485 interface: without RS-485 interface with RS-485 interface 1 Connection for moulds: common connectors for thermocouples and heaters 1 separate connectors for thermocouples and heaters1) 2 Acceptance tests: without extra quality requirements 0 with an extra quality inspection certificate 1 acc. to customer’s request2) X Connection set ZP11 - X X X Kind of system: SR11 with 1 controller one common cable for thermocouples and heaters 1 SR11 with 2,3,4,5,6,7,8 controllers one common cable for thermocouples and heaters 1) 2 SR11 with 4, 5, 6 controllers one cable for thermocouples 3 SR11 with 4, 5, 6 controllers one cable for heaters 4 SR11 with 7, 8 controllers one cable for thermocouples 5 SR11 with 7, 8 controllers one cable for heaters 6 Cable length: 3 m 1 6 m 2 Acceptance tests: without extra quality requirements 8 with an extra quality inspection certificate 7 acc. to customer’s request 2) X Set of sockets for moulds GP11 - X Kind of socket: one male socket for mould and ZP11-1XX connection set 1 one male socket for mould and ZP11-2XX1), ZP11-4XX and ZP11-6XX 2) 2 one female socket for mould and ZP11-3XX and ZP11-5XX 3) connection set 3 ORdeRiNg exAmple: The code: SR11-6 5 0 1 8 - means: system for moulds with heated channels, in a housing of 365 mm width, with 5 controllers, without RS-485 interface, with common connectors for thermocouples and heaters, without extra quality requirements. ORdeRiNg exAmple: The code: Zp11-1 2 8 - means: connection set of ZP11 type for the SR11 system, with 1 controller for mould with heated channels, with a cable of 6 m long, without extra quality requirements. 1) For cables with common wires for heaters and thermocouples, one male socket for one cable is required. 2) For cables with separated wires for heaters and thermocouples, one male socket for one heater cable is required. 3) For cables with separated heater and thermocouple wires, for one thermocouple cable, one female socket is required. 1) concerns only versions with 365 mm and 465 mm housing width 2) after agreeing with the manufacturer 1) for SR11 systems with 5, 6, 7, 8 controllers, 2 cables are required 2) after agreeing with the manufacturer ORdeRiNg exAmple: The code: gp11- 3 - means: set of sockets for moulds of GP11 type, with one female socket for mould, for the thermocouple wire of the connection set with separated heater and ther- mocouple wires. SR11 system for injection moulds with heated channels For more information about LUMEL’s products please visit our website: www.lumel.com.pl