SPUBC24120 CARLOGAVAZZI | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Smart Power Supply and UPS Type SPUBC 24V 5A Output Data Ordering KeyApprovals Power supply UPS battery charger Battery and Output Voltage Vdc Output power W SPUBC 24 120 Output voltage 24Vdc Nominal current 5A Rated output current 5A Efficiency (@50% of rated current) ≥90% Turn on delay 1S (Max) Max Capacitive load startup Unlimited Power dissipation @ Max. Load 17W Short circuit protection Yes Over load protection Yes Overvoltage output protection Yes (typ. 35Vdc) Thermal protection Yes 1 Specifications are subject to change without notice. Pictures are just an example. For special features and/or customization, please ask to our sales network. 17/06/2015
- Single phase input 115Vac / 230Vac / 277Vac
- Smart power management
- Rated output 5A with permanent 10A overboost
- Max battery charging current 5A
- Suitable for Lead Acid open or sealed, Lead gel
- Automatic Battery diagnostic and battery care
- Boost, Trikle/float and recovery charging cycles.
- Battery reversed polarity, element short circuit or disconnection
- 2 relay outputs for remote status and operation indication
- cURus recognized and CE approved Product Description The new Carlo Gavazzi SPUBC puts you in the driving seat of your power management requirements, allocating power, in the most efficient way, between the load and the battery.The maximum available current for battery charging is set by means of a front trimmer. It can go from 20% to 100%, which means that it possible to charge with up to 5A. The priority though is always the load. If the load requires 80% of current, the current available for the battery is only the remaining 20% regardless of the setting. On the SPUBC24120 the rated output current is 5A, although, after the battery is charged, the power supply can provide 10A. SPUBC implements a comprehensive process called “Battery Care” that applies algorithms to obtain rapid and automatic charging, battery charge optimization over time, flat battery recovery and real time diagnostic during installation and operation. The Real Time auto- diagnostic system, monitors battery faults such as battery sulphatation, elements in short circuit, accidental reverse polarity connection and battery disconnection or bad connection. All these can be easily detected and removed during installation and operation by the “diagnostic LED” Blinking Code. Continuous battery efficiency monitoring, reduces battery damage risk and allows safe operation in permanent connection. This device is suitable for a selection of most common battery types. By means of built in jumpers it is possible to set preset curves. They are programmed for two charging levels, boost and float/trikle, but can be changed to single charging level by the user. In addition to the SPUBC, Carlo Gavazzi, also provides a selection of Racks for DIN rail mounting of the battery, with battery included upon request from 1.2Ah up to 12Ah capable of providing, depending upon load, from a few minutes to several hours of charge reserve.
2 Specifications are subject to change without notice. Pictures are just an example. For special features and/or customization, please ask to our sales network. 17/06/2015 Smart Power Supply and UPS Type SPUBC 24V 5A Input Data Frequency 47 ÷ 63Hz Input current (115 - 230Vac) 2.8 ~ 1.3A Internal fuse (not replaceable) 4A External fuse MCB curve B 10A Nominal input voltage 115 ~ 230 ~ 277Vac Voltage range 90 ÷ 305Vac Inrush current (Vn - In nom. Load) I2t ≤ 11A ≤ 5ms General Data Dimensions W x H x D 65 x 115 x 135mm Weight 0.6Kg approx. Operating temperature -25°C ~ 70°C Derating Ta >50°C -2.5% (In)/°C Storage temperature -40°C ~ +85°C Ambient Humidity RH 95% not condensing Cooling Natural air flow, convection Insulation voltage IN / OUT 3000Vac IN / GND 1605Vac OUT / GND 500Vac Protection Degree EN/IEC 60529 IP20 Pollution degree 2 Connection wires size 2.5mm (24-14AWG) Protection class I (IEC61140) (with PE connected) Battery Charger (@ 25°C Ambient, Inom) Charging current Adjustment 20 ~ 100% Inom Reverse battery protection Yes Sulfated battery check Yes Detection of battery element in short circuit Yes Quiescent current ≤ 5mA Charging Profile 3 stage Remote input control Boost / Trickle Boost charge 28.8Vdc Max. Boost charge duration 15h Min. duration boost charge 1min. Trickle charge 27.5Vdc MTBF IEC 61709 > 300.000h Recovery charge 2 ~ 16Vdc Max. Charging current 5A ± 5% Power Supply Output (@ 25°C Ambient, Inom) Max current output load 15A x 4s Max Total discharge protection 19 ~ 20Vdc batt Flat battery alarm 20 ~ 21Vdc batt Output voltage 22 ~ 28.8Vdc Output Current 1.1 x In A ±5% Continuos current (without battery) 5A Continuos current (with battery) 10A Signal Outputs Mains or backup power Yes Low battery Yes Battery fault Yes Relay outputs Type 2 x SPDT Max. AC Load AC1 1A @ 60Vac Max. DC Load DC1 1A @ 30Vdc Min. Load 1mA @ 5Vdc Signal Port RJ45 (RJ 45 Auxiliary Output behind the label; remove the window label to find the connector) Can Bus NoBattery temp. Compensation Yes. It is possible connect a temperature sensor, for ambient temperature charging compensation. Remote monitoring display Yes. It is possible connect an external display to remote N° 3 led of the internal device.
+ - BUSDC Battery DC AC Battery DC AC DC BUS -SPD24RM20 / SPM2RM2410 DC AC Battery Battery Battery Battery Smart Power Supply and UPS Type SPUBC 24V 5A + - BUSDC Battery DC AC Battery DC AC DC BUS -SPD24RM20 / SPM2RM2410 DC AC Battery Battery Battery Battery DC Aux2 AC DC MASTER BUS Battery Battery DC Aux2 AC DC AC DC BUS Battery Battery Battery Battery DC AC Specifications are subject to change without notice. Pictures are just an example. For special features and/or customization, please ask to our sales network. 17/06/2015 3 Output Power Connections Signals and Terminals Normal connection A: Mains Terminals (input) B: Battery and load terminals C: Backup mode output D: Battery status output E: Backup mode LED F: Battery status LED G: Diagnosis LED H: Battery configuration jumpers J: Charging level adjustment (from 20 to 100%) K: Fast charge enabling jumper L: Remote battery start M: Local battery start Parallel connection “Redundancy” Parallel connection “Double Power” Series connection M G F E J B D A H L K C
Buffering Time / Battery Capacity Accessories 4 Specifications are subject to change without notice. Pictures are just an example. For special features and/or customization, please ask to our sales network. 17/06/2015 Smart Power Supply and UPS Type SPUBC 24V 5A Battery capacity Load 1.2Ah SPUBATxx1A2 3.2Ah SPUBATxx3A2 7.2Ah SPUBATxx7A2 12Ah SPUBATxx12 100Ah 1.5A 20’ 60’ 200’ 400’ - 3A 8’ 30’ 120’ 240’ - 5A 3’ 15’ 55’ 100’ - 10A no 7’ 20’ 45’ 20h Ordering Code Description Type Voltage Battery Capacity Max. Charging current Weight Width mm Height mm Depth mm SPUBAT241A2 DIN Rail Rack with 1.2Ah Battery Lead Acid VRLA 24V 1.2Ah 0.3A 1.5Kg 62 185 120 SPUBAT243A2 DIN Rail Rack with 3.2Ah Battery Lead Acid VRLA 24V 3.2Ah 0.8A 3Kg 82 200 160 SPUBAT247A2 DIN Rail Rack with 7.2Ah Battery Lead Acid VRLA 24V 7.2Ah 1.7A 5.5Kg 145 210 130 SPUBAT1A2 Empty DIN Rail Rack for 1.2Ah Battery - 12V or 24V Designed for 1.2Ah - ? 62 175 120 SPUBAT3A2 Empty DIN Rail Rack for 3.2Ah Battery - 12V or 24V Designed for 3.2Ah - ? 82 200 160 SPUBAT7A2 Empty DIN Rail Rack for 7.2Ah Battery - 12V or 24V Designed for 7.2Ah - ? 145 210 130 SPUBAT12 Empty DIN Rail Rack for 12Ah Battery - 12V or 24V Designed for 12Ah - ? 210 210 210